1996 TOYOTA LAND CRUISER Cruise control

SF1F9−01
−
SFI VSV FOR FUEL PRESSURE CONTROL
SF−59
687
Author: Date:
1996 LAND CRUISER (RM451U)
VSV FOR FUEL PRESSURE
CONTROL
INSPECTION
1. REMOVE AIR INTAKE CHAMBER (See page EM−28 )
2. DISCONNECT VACUUM HOSES AND CONNECTOR
3. INSPECT VSV FOR OPEN CIRCUIT
Using an ohmmeter, check that there is continuity between the
terminals. Resistance: 37 − 44 Ω at 20° C (68°F)
If there is no continuity, replace the VSV.
4. INSPECT VSV FOR GROUND
Using an ohmmeter, check that there is no continuity between
each terminal and the body.
If there is continuity, replace the VSV.
5. INSPECT VSV OPERATION
(a) Check that the air flows from pipe E to pipe G.
(b) Apply battery voltage across the terminals.
(c) Check that the air does not flows from pipe E to the filter.
If operation is not as specified, replace the VSV.
6. RECONNECT VACUUM HOSES AND CONNECTOR
7. REINSTALL AIR INTAKE CHAMBER (See page EM−54 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0Q0−07
−
SFI ENGINE CONTROL MODULE (ECM)
SF−65
693
Author: Date:
1996 LAND CRUISER (RM451U)
ENGINE CONTROL MODULE (ECM)
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0Q1−07
SF−66
−
SFI ENGINE CONTROL MODULE (ECM)
1996 LAND CRUISER (RM451U)
INSPECTION
1. REMOVE ECM
2. INSPECT ECM (See page DI−17 )
3. REINSTALL ECM
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR−12
−
STEERING TILT STEERING COLUMN
1996 LAND CRUISER (RM451U)
3. REMOVE INSTRUMENT LOWER FINISH PANEL
(a) Disconnect the hood lock control cable and fuel lid control
cable.
(b) Remove the 4 panel set screws.
4. REMOVE NO.2 HEATER TO REGISTER DUCT
5. REMOVE UPPER AND LOWER COLUMN COVERS
Remove the 5 screws.
6. REMOVE COMBINATION SWITCH WITH SPIRAL CABLE
(a) Disconnect the 2 connectors.
(b) Disconnect the airbag connector.
(c) Remove the 4 screws.
NOTICE:
Do not disassemble the cable or apply oil to it.
7. REMOVE 4 COLUMN HOLE COVER SET BOLTS
8. REMOVE LINK JOINT PROTECTOR
Remove the 2 bolts.
9. DISCONNECT SLIDING YOKE SUB−ASSEMBLY
(a) Place matchmarks on the yoke sub −assembly and worm
gear valve body shaft.
(b) Loosen bolt A and remove bolt B.
10. REMOVE SLIDING YOKE SUB−ASSEMBLY
Remove the bolt A.
11. REMOVE TILT STEERING COLUMN ASSEMBLY
(a) Disconnect the 3 connectors.
(b) Remove the 2 column assembly set nuts and 2 set bolts.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR16E−03
−
STEERING TILT STEERING COLUMN
SR−19
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL STEERING COLUMN ASSEMBLY
(a) Torque the 2 column assembly set nuts and 2 set bolts.
Torque:25 N·m (250 kgf·cm, 18 ft·lbf)
(b) Connect the 3 connectors.
2. INSTALL SLIDING YOKE SUB −ASSEMBLY
Temporarily tighten the bolt A.
3. CONNECT SLIDING YOKE SUB−ASSEMBLY
(a) Align the matchmarks on the yoke sub−assembly and
worm gear valve body shaft.
(b) Torque the bolt B. Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
(c) Torque the bolt A.
Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
4. INSTALL LINK JOINT PROTECTOR
Torque the 2 bolts. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
5. TORQUE 4 COLUMN HOLE COVER SET BOLTS Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
6. INSTALL COMBINATION SWITCH WITH SPIRAL CABLE
(a) Tighten the 4 screws.
(b) Connect the airbag connector.
(c) Connect the 2 connectors.
7. INSTALL UPPER AND LOWER COLUMN COVERS
Tighten the 5 screws.
8. INSTALL NO.2 HEATER TO REGISTER DUCT
9. INSTALL INSTRUMENT LOWER FINISH PANEL
(a) Tighten the 4 panel set screws.
(b) Connect the hood lock control cable and fuel lid control cable.
10. CENTER SPIRAL CABLE
(a) Check that the front wheels are facing straight ahead.
(b) Turn the cable counterclockwise by hand until it becomes harder to turn the cable.
(c) Then rotate the cable clockwise about 3 turns to align the
red mark.
HINT:
The cable will rotate about 3 turns to either left or right of the
center.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR16H−01
R08084
R08066
Soft Jaws
R13187
Press
SST
SST
R08067
Screwdriver
SR−24
−
STEERING POWER STEERING VANE PUMP
1996 LAND CRUISER (RM451U)
DISASSEMBLY
NOTICE:
When using a vise, do not overtighten it.
1. MEASURE POWER STEERING VANE PUMP ROTAT-
ING TORQUE
(a) Check that the pump rotates smoothly without abnormal noise.
(b) Using a torque wrench, check the pump rotating torque. Rotation torque:
0.3 N·m (2.8 kgf·cm, 2.4 in.·lbf) or less
2. REMOVE SUCTION PORT UNION
(a) Remove the bolt.
(b) Remove the O−ring from the union.
3. REMOVE VANE PUMP DRIVE GEAR
(a) Using soft jaws on a vise, clamp the gear in the vise.
NOTICE:
Be careful not to damage the gear.
(b) Remove the gear set nut.
(c) Using SST, press out the gear.
SST 09527−10011
NOTICE:
Be careful not to damage the gear. To avoid dropping the
PS pump assembly, support the pump assembly with your
hand.
(d) Remove the woodruff key from the vane pump shaft.
4. REMOVE PRESSURE PORT UNION, FLOW CONTROL
VALVE AND SPRING
Remove the O−ring from the union.
5. REMOVE REAR HOUSING AND WAVE WASHER
(a) Using 2 screwdrivers, remove the snap ring.
NOTICE:
Take care not to damage the housing.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

V08067
Rotor
markCam ring
mark Vane plate part
number Vane plate length
mm (in.)
14.995 − 14.997
(0.59035 − 0.59043)
44345
−60030
2
None
1 3 44345
−60040 14.993
− 14.995
(0.59027 − 0.59035)
14.991 − 14.993
(0.59020 − 0.59027)
44345
−60050
4
2
R08078
SR3776
Compressed Air
R08702
SR−28
−
STEERING POWER STEERING VANE PUMP
1996 LAND CRUISER (RM451U)
HINT:
There are 3 vane plate lengths for the following rotor and cam
ring marks.
3. INSPECT FLOW CONTROL VALVE
(a) Coat the valve with power steering fluid and check that it
falls smoothly into the valve hole by its own weight.
(b) Check the valve for leakage. Close one of the holes and apply 392 − 490 kPa (4 − 5 kgf/cm
2, 57 − 71 psi) of com-
pressed air into the opposite side, and confirm that air
does not come out from the end holes.
Inscribed mark:
A, B, C, D, E or F
4. INSPECT SPRING
Using calipers, measure the free length of the spring. Minimum free length: 35 − 37 mm (1.38 − 1.46 in.)
If it is not within the specification, replace the spring.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R08069
R08082
R08066
Soft Jaws
−
STEERING POWER STEERING VANE PUMP
SR−31
1996 LAND CRUISER (RM451U)
9. INSTALL WAVE WASHER
Install the washer so that its protrusions fit into the slots in the
side rear plate.
10. INSTALL REAR HOUSING
(a) Coat a new O−ring with power steering fluid and install it
to the housing.
(b) Using a press, apply just enough pressure to compress the wave washer, and install a new snap ring to the front
housing.
11. INSTALL SPRING, FLOW CONTROL VALVE AND PRESSURE PORT UNION
(a) Install the valve facing the correct direction. (See page SR−21 )
(b) Coat a new O −ring with power steering fluid and install it
to the union.
(c) Torque the union. Torque: 69 N·m (700 kgf·cm, 51 ft·lbf)
12. INSTALL VANE PUMP DRIVE GEAR
(a) Install the woodruff key and gear.
(b) Using soft jaws on a vise, clamp the gear in the vise.
NOTICE:
Be careful not to damage the gear.
(c) Torque the gear set nut. Torque: 74 N·m (750 kgf·cm, 54 ft·lbf)
13. MEASURE POWER STEERING PUMP ROTATING
TORQUE (See page SR−24 )
14. INSTALL SUCTION PORT UNION
(a) Coat a new O −ring with power steering fluid and install it
to the union.
(b) Torque the bolt.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010