1996 TOYOTA LAND CRUISER egr temp sensor

−
ENGINE MECHANICAL CYLINDER HEAD
EM−61
1996 LAND CRUISER (RM451U)
14. INSTALL HEATER PIPE
Install a new gasket, the heater pipe and ground cable with the
2 bolts and 2 nuts.
Torque:
20 N·m (200 kgf·cm, 14 ft·lbf) for bolt:
21 N·m (210 kgf·cm, 15 ft·lbf) for nut
15. INSTALL NO. 1 AND NO. 2 EXHAUST MANIFOLDS
(a) Install 2 new gaskets, No. 1 exhaust manifold and No. 2
exhaust manifold with the 13 nuts.
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
(b) Install the No. 1 heat insulator and No. 2 heat insulator with the 6 bolts.
Torque: 19 N·m (195 kgf·cm, 14 ft·lbf)
16. INSTALL FRONT EXHAUST PIPE
(a) Install 2 new gaskets and the front exhaust pipe with the 4 nuts.
Torque: 63 N·m (630 kgf·cm, 46 ft·lbf)
(b) Install the No. 1 support bracket with the 2 bolts. Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
(c) Connect the clamp and tighten the clamp bolt.
Torque: 19.5 N·m (195 kgf·cm, 14 ft·lbf)
(d) Connect the front exhaust pipe to the rear TWC with a new gasket, 2 bolts and 2 nuts.
Torque: 46 N·m (470 kgf·cm, 34 ft·lbf)
17. CONNECT NO. 2 WATER BYPASS PIPE
Connect the bypass pipe to the cylinder head with the 3 bolts.
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
18. CONNECT ENGINE WIRE
(a) Place the engine wire on the intake manifold.
(b) Connect the connectors. (1) Connect the 3 injector connectors.
(2) Connect the EGR gas temp. sensor connector.
(c) Connect the clamp of the No.6 injector wire to the bracket.
(d) Connect the engine wire clamp.
(e) Connect the engine wire clamp.
(f) Connect the connectors. (1) Connect the connector for the emission control
valve set assembly.
(2) Connect the 3 injector connectors.
(g) Install the bolt holding the engine wire to the intake man- ifold.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1EN−01
SF−26
−
SFI INJECTOR
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. DISCONNECT CRUISE CONTROL ACTUATOR CABLE
3. DISCONNECT ACCELERATOR CABLE
4. DISCONNECT THROTTLE CABLE
5. DISCONNECT NO.2 PCV HOSE
6. DISCONNECT AIR CLEANER HOSE
7. REMOVE EGR VACUUM MODULATOR AND VALVE (See page EC−10 )
8. REMOVE BOLT HOLDING HEATER INLET PIPE AND AIR INTAKE CHAMBER
9. DISCONNECT NO.1 PCV HOSE
10. DISCONNECT VACUUM SENSING HOSE
11. DISCONNECT NO.2 WATER BYPASS HOSE
12. DISCONNECT EVAP HOSE
13. DISCONNECT BRAKE BOOSTER HOSE
14. DISCONNECT THROTTLE POSITION SENSOR CON- NECTOR
15. DISCONNECT IDLE AIR CONTROL VALVE CONNEC-
TOR
16. DISCONNECT CONNECTOR FOR EMISSION CON- TROL VALVE SET ASSEMBLY
17. DISCONNECT EGR GAS TEMP. SENSOR CONNEC-
TOR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF−34
−
SFI INJECTOR
1996 LAND CRUISER (RM451U)
7. INSTALL INTAKE MANIFOLD STAY
Install the intake manifold stay with the 2 bolts.
Torque: 36 N·m (360 kgf·cm, 26 ft·lbf)
8. CONNECT GROUND STRAP
9. INSTALL ENGINE OIL DIPSTICK
10. CONNECT PS RESERVOIR TANK
Connect the reservoir tank with the 3 bolts. Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
11. CONNECT EGR GAS TEMP. SENSOR CONNECTOR
12. CONNECT CONNECTOR FOR EMISSION CONTROL VALVE SET ASSEMBLY
13. CONNECT IDLE AIR CONTROL VALVE CONNECTOR
14. CONNECT THROTTLE POSITION SENSOR CONNEC- TOR
15. CONNECT BRAKE BOOSTER HOSE
16. CONNECT EVAP HOSE
17. CONNECT NO.2 WATER BYPASS HOSE
18. CONNECT VACUUM SENSING HOSE
19. CONNECT NO.1 PCV HOSE
20. INSTALL BOLT HOLDING HEATER INLET PIPE AND AIR INTAKE CHAMBER
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
21. INSTALL EGR VALVE AND VACUUM MODULATOR (See page EC−10 )
22. CONNECT THROTTLE CABLE
23. CONNECT ACCELERATOR CABLE
24. CONNECT CRUISE CONTROL ACTUATOR CABLE
25. CONNECT AIR CLEANER HOSE
26. CONNECT NO.2 PCV HOSE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1FA−01
FI6320
Ohmmeter
Oil
−
SFI EXHAUST GAS RECIRCULATION (EGR) GAS
TEMPERATURE SENSORSF−63
691
Author: Date:
1996 LAND CRUISER (RM451U)
EXHAUST GAS RECIRCULATION
(EGR) GAS TEMPERATURE
SENSOR
INSPECTION
1. REMOVE EGR GAS TEMPERATURE SENSOR
2. INSPECT EGR GAS TEMPERATURE SENSOR
Using an ohmmeter, measure the resistance between the ter-
minals.
TemperatureResistance
50 °C (122° F)64 − 97 kΩ
100°C (212° F)11 − 16 kΩ
150 °C (302° F)2 − 4 kΩ
If the resistance is not as specified, replace the sensor.
3. REINSTALL EGR GAS TEMPERATURE SENSOR
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1ES−01
−
SERVICE SPECIFICATIONS SFI
SS−11
134
Author: Date:
1996 LAND CRUISER (RM451U)
SFI
SERVICE DATA
Fuel pressure
regulatorFuel pressure at no vacuum265 − 304 kPa (2.7 − 3.1 kgf/cm2, 38 − 44 psi)
Fuel pumpResistance at 20°C (68° F)0.2 − 3.0 Ω
InjectorResistance at 20°C (68° F)
Injection volume
Difference between each cylinder
Fuel leakage13.4 − 14.2 Ω
69 − 88 cm3 (4.2 − 5.4 cu in.) per 15 sec.
5 cm3 (0.3 cu in.) or less
1 drop or less per 12 min.
MAF meterResistance (THA − E2) at −20° C (− 4°F)
at 0° C (32° F)
at 20° C (68° F)
at 40° C (104° F)
at 60° C (140° F)
at 80° C (176° F)10 − 20 kΩ
4 − 7 kΩ
2 − 3 kΩ
0.9 − 1.3 kΩ
0.4 − 0.7 kΩ
0.2 − 0.4 kΩ
Throttle bodyThrottle body fully closed angle
Dashpot setting speed
Throttle opener setting speed6°
2,200 ± 300 rpm
700 − 1,000 rpm
Throttle position
sensorClearance between stop screw and lever
0 mm (0 in.) VTA − E2
0.50 mm (0.020 in.) IDL − E2
0.75 mm (0.030 in.) IDL − E2
Throttle valve fully open VTA − E2
− VC − E2
0.2 − 5.7 kΩ
2.3 kΩ or less
Infinity
2.0 − 10.2 kΩ
2.5 − 5.9 kΩ
IAC valveResistance (B1 − S1 and S3, B2 − S2 and S4)
at cold (− 10 − 50 ° C (−50 − 122° F))
at hot (50 − 100°C (122 − 212°F))
15 − 25 Ω
20 − 30 Ω
Fuel pump resistorResistance at 20°C (68° F)0.70 − 0.76 Ω
VSV for fuel pres-
sure controlResistance at 20°C (68° F)37 − 44 Ω
ECT sensorResistance at −20° C (− 4°F)
0 °C (32° F)
20 °C (68° F)
40 °C (104° F)
60 °C (140° F)
80 °C (176° F)10 − 20 kΩ
4 − 7 kΩ
2 − 3 kΩ
0.9 − 1.3 kΩ
0.4 − 0.7 kΩ
0.2 − 0.4 kΩ
EGR gas temp
sensorResistance at 50°C (122° F)
at 100° C (212° F)
150 °C (302° F)64 − 97 kΩ
11 − 16 kΩ
2 − 4 kΩ
Heated oxygen
sensorHeater coil resistance at 20°C (68° F)11 − 16 Ω
Fuel cut rpmFuel return rpm1,200 rpm
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1ET−01
SS−12
−
SERVICE SPECIFICATIONS SFI
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Fuel line for union bolt
for flare nut29
30300
31022
22
Second seat x Body3940029
Fuel pump bracket assembly x Fuel tank3.94035 in.·lbf
Fuel inlet hose x Fuel filter2930022
Fuel inlet pipe x Fuel filter2930022
Fuel filter x Intake manifold2121015
Fuel pressure regulator x Delivery pipe2525018
Delivery pipe x Intake manifold2121015
Fuel inlet pipe x Delivery pipe Union bolt
Bolt29
20300
20022
14
Fuel inlet pipe x Fuel filter2930022
Fuel return pipe x Intake manifold2020014
Air intake chamber x Intake manifold2121015
Intake manifold stay x Air intake chamber3636026
Intake manifold stay x Cylinder block3636026
PS reservoir tank x Air intake chamber1818513
Heater inlet pipe x Air intake chamber2020014
Drain plug x Fuel tank6.56557 in.·lbf
Fuel tank breather tube x Fuel tank1.51513 in.·lbf
Fuel tank filler pipe x Fuel tank3.53531 in.·lbf
Fuel tank band x Body3940029
MAF meter x Bracket6.97061 in.·lbf
MAF meter x Air cleaner cap6.97061 in.·lbf
Throttle body x Air intake chamber2121015
Fuel pump resistor x Body1818513
ECT sensor x Cylinder head24.525017.5
EGR gas temperature sensor x Air intake chamber2020014
Knock sensor x Cylinder block4445033
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010