1996 TOYOTA LAND CRUISER Replace battery terminals

CH0EO−02
CH0712
BlueRed
White
Charging
Necessary
OK
Add Distilled
Water
CH−2
−
CHARGING CHARGING SYSTEM
1996 LAND CRUISER (RM451U)
CHARGING SYSTEM
ON−VEHICLE INSPECTION
1. CHECK BATTERY ELECTROLYTE LEVEL AND VOLT-
AGE
(a) Check the electrolyte quantity of each cell.
If under the lower level, replace the battery (or add distilled wa-
ter if possible). check the charging system.
(b) Measure the battery voltage between the negative ( −)
and positive (+) terminals of the battery.
Standard voltage: At 20° C (68°F): 12.7 − 12.9 V
HINT:
Before measuring the voltage, turn the ignition switch
OFF and turn off the electrical systems (headlight, blower
motor, rear defogger etc.).
If the vehicle has been running, wait 20 minutes or more
after the vehicle stops before measuring the battery volt-
age.
If the voltage is less than specification, charge the battery.
HINT:
Check the indicator as shown in the illustration.
2. CHECK BATTERY TERMINALS, FUSIBLE LINK AND FUSES
(a) Check that the battery terminals are not loose or cor-
roded.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00203
CloseOpen Battery
Battery
B1
S1
S2 B2S4
S3
B1
S1 S2 B2S4S3
P24670
P24671
DI−92
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
4 Check operation of the IAC valve .
PREPARATION:
Remove IAC valve (See page SF−51).
CHECK:
(a) Connect the positive (+) leak from the battery to terminals
5 (B1) and 2 (B2), and the negative ( −) lead to terminals
4 (S1), −1 (S2), −6 (S3), −3 (S4) in that order.
(b) Connect the positive (+) lead from the battery to terminals
5 (B1) and 2 (B2), and the negative ( −) lead to terminals
3 (S4), − 6 (S3), −1 (S2), − 4 (S1) in that order.
OK:
(1) The valve moves to close direction.
(2) The valve moves to open direction.
HINT:
The ACTIVE TEST mode of the T OYOTA hand−held tester can
be used to change the step of the IAC valve as desired.
NG Repair or replace IAC valve.
OK
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24681
DI−11 2
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
4 Check IGN fuse from fuse block.
NG Check for short in all the harness and
components connected to IGN fuse.
OK
5 Check ignition switch.
PREPARATION:
(a) Remove instrument lower finish panel.
(b) Remove instrument cluster finish center panel No.2.
CHECK:
Check continuity between terminals.
OK:
Shift PositionTerminal No. to continuityTerminal No. to continuity
LOCK−−
ACC3 − 4−
ON2 − 3 − 46 − 11
START1 − 2 − 45 − 6 − 11
NG Replace ignition switch.
OK
Check for open and short in harness and
connector between battery and ignition
switch and ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00193
Continuity ContinuityOpen
Open (+) (−) 1
2
3
4
5
6
1
2
3
6
54
P24685
P24686
P24687
FPR
(+)
(−)
−
DIAGNOSTICS ENGINE
DI−11 9
1996 LAND CRUISER (RM451U)
5 Check operation of fuel pump relay.
PREPARATION:
(a) Disconnect fuel pump relay connector.
(b) Remove fuel pump relay.
CHECK:
Check continuity between terminals of fuel pump relay.
OK:
Terminals 3 and 5Continuity
Terminals 2 and 5Open
Terminals 1 and 5Continuity
(Reference value 80 Ω)
CHECK:
(a) Apply battery voltage between terminals 1 and 5.
(b) Measure voltage between terminals 1 and 2.
OK:
Terminals 1 and 2Battery voltage
NG Replace fuel pump relay.
OK
6 Check voltage between terminal FPR of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Start the engine.
CHECK:
Measure voltage between terminal FPR of ECM and body
ground while racing the engine.
OK:
Time after engine startedVoltage
60 seconds or more0 − 3 V
Less than 60 seconds9 − 14 V
OK Check and replace ECM (See page IN−28 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08235
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−181
1996 LAND CRUISER (RM451U)
3 Check PWR mode switch.
PREPARATION:
Disconnect the pattern select switch connector.
CHECK:
Check the resistance between terminals of the pattern select
switch connector when the PWR mode switch is set to PWR and
NORM positions.
OK:
PWR Mode SwitchResistance
PWR0 Ω (continuity)
NORM∞ Ω (open)
NG Replace pattern select switch.
OK
4 Check harness and connector between battery and pattern select switch, a\
nd pattern select switch and ECM (See page IN−28).
NG Repair or replace harness or connector.
OK
Check and replace ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08234
D00096
ONHOLD
HI
DI−184
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
3 Check 2nd start switch.
PREPARATION:
Disconnect the pattern select switch connector.
CHECK:
Check the resistance between terminals 2 and 5 of the pattern
select switch connector when the pattern select switch is set to
2nd start switch ON and OFF.
OK:
2nd Start SwitchResistance
ON0 Ω (continuity)
OFF∞ Ω (open)
NG Replace pattern select switch.
OK
4 Check voltage between terminals HOLD and HI of ECM and body ground.
PREPARATION:
(a) Turn ignition switch ON.
(b) Disconnect the connector from the ECM.
CHECK:
Check the voltage between terminal HOLD of the ECM and
body ground when the select switch is set to 2nd start switch ON
and OFF.
OK:
2nd Start SwitchVoltage
ON9 − 14 V
OFFBelow 1.5 V
CHECK:
Check the voltage between terminal HI of the ECM and body
ground.
OK:
Voltage: 7.5 − 14 V
OK Check and replace ECM.
NG
Check and replace harness and connector between battery and patten select switch, pattern se-
lect switch and ECM, battery and 2nd start indicator light, and 2nd start in\
dicator light and ECM
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08234
D00096
ONHOLD
HI
DI-187
-
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
3 Check 2nd start switch.
PREPARATION:
Disconnect the pattern select switch connector.
CHECK:
Check continuity between terminals 2 and 5 of pattern select
switch connector when pattern select switch is set to 2nd start
switch ON and OFF.
OK:
2nd start switchSpecified condition
Press continuously º2ndº switch0 W (Continuity)
Release º2ndº switch8 W (open)
NG Replace pattern select switch.
OK
4 Check voltage between terminals HOLD and HI of ECM and body ground.
PREPARATION:
(a) Turn ignition switch ON.
(b) Disconnect the connector of ECM.
CHECK:
Check voltage between terminal HOLD of ECM and body
ground when the select switch is set to 2nd start switch ON and
OFF.
OK:
2nd start switchVoltage
ON9 - 14 V
OFFBelow 1.5 V
CHECK:
Check voltage between terminal HI of ECM and body ground.
OK:
Voltage: 7.5 - 14 V
OK Check and replace the ECM.
NG
Check and replace harness and connector between battery and patten select swi\
tch, pattern se-
lect switch and ECM, battery and 2nd start indicator light , 2nd start indic\
ator light and ECM
(See page IN-27 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R14139
ContinuityOpen
Continuity
1
2
5
6
3
A6
A7
R14140
(−) (+)
Continuity
Open
36
51
2
A6 A7
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−203
1996 LAND CRUISER (RM451U)
3 Check ABS control (solenoid) relay.
CHECK:
Check the continuity between each terminal of the ABS control
(solenoid) relay.
OK:
Terminals A7 −1 and A6− 3Continuity
(Reference value aprox. 80 Ω)
Terminals A7 −5 and A7− 6Continuity
Terminals A7 −2 and A7− 5Open
CHECK:
(a) Apply battery positive voltage between terminals A7 −1
and A6−3.
(b) Check the continuity between each terminal of the ABS control (solenoid) relay.
OK:
Terminals A7 −5 and A7− 6Open
Terminals A7 −2 and A7− 5Continuity
NG Replace ABS control relay.
OK
4 Check for open and short in harness and connector between ABS control (\
sole- noid) relay and ABS ECU (See page IN−28).
NG Repair or replace harness or connector.
OK
If same code is still output after DTC is deleted, check contact condition of each connection.\
If
connections are normal, ECU may be defective.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010