1996 TOYOTA LAND CRUISER Fuse spec

A00484
Intake Air Temp. Sensor
(Inside the mass air flow meter)
3
4 L−Y
BR−B 5V
ECM
E5
E5
THA
E1
E2
P22420
3
9 R
−
DIAGNOSTICS ENGINE
DI−27
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
If DTCs P0110 (Intake Air Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction),
P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction)\
are output simultaneously, E2 (Sen-
sor Ground) may be open.
1 Connect the OBD II scan tool or TOYOTA hand −held tester, and read value of
intake air temperature.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand−held tester to DLC3.
(c) Turn ignition switch ON and OBD II scan tool or TOYOTA hand−held tester main switch ON.
CHECK:
Read temp. value on the OBD II scan tool or TOYOTA hand −held tester.
OK:
Same as actual intake air temp.
HINT:
If there is open circuit, push OBD II scan tool or TOYOTA hand− held tester indicates − 40° C (− 40°F).
If there is short circuit, OBD II scan tool or TOYOTA handheld tester indicates 140° C (284°F) or more.
NG − 40° C (− 40 °F) ....Go to step 2.
140 °C (284°F) or more ....Go to step 4.
OK
Check for intermittent problems
(See page DI−3 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00156
ON
Engine Coolant
Temp. Sensor ECM
5V
4
9
2
1
E2
E1
THW
E5
E5
BE6653
FI7055
−
DIAGNOSTICS ENGINE
DI−31
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
HINT:
If DTC is P0110 (Intake Air Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction),
P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction)\
are output simultaneously, E2 (Sen-
sor Ground) may be open.
1 Connect the OBD II scan tool or TOYOTA hand −held tester, and read value of
engine coolant temperature.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and push the OBD II scan tool or TOYOTA hand−held tester main switch ON.
CHECK:
Read temperature value on the OBD II scan tool or TOYOTA hand −held tester.
OK:
Same as actual engine coolant temperature.
HINT:
If there is open circuit, OBD II scan tool or TOYOTA hand−held tester indicates − 40°C (− 40 °F).
If there is short circuit, OBD II scan tool or T OYOTA hand−held tester indicates 140 °C (284 °F) or more.
NG −40°C ( −40° F) ... Go to step 2.
140 °C (284° F) or more ... Go to step 4.
OK
Check for intermittent problems
(See page DI−3 ).
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect the engine coolant temp. sensor connector.
(b) Connect sensor wire harness terminals together.
(c) Turn ignition switch ON.
CHECK:
Read temp. value on the OBD II scan tool or TOYOTA hand −
held tester.
OK:
Temp. value: 140° C (284°F) or more
OK Confirm good connection at sensor. If OK, replace engine coolant temp. sensor.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00483
2
1 3 4R−G
G−B
G−W
BR−B
Throttle Position Sensor
* Closed Throttle
Position Switch
* E5 E5
E5 E5
10 1
11 9 VTA
E2 VCC
IDL 5V
E1 B+
P22422
ECM
FI7052
DI−36
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
If DTCs P0110 (Intake Air Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction),
P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction)\
are output simultaneously, E2 (Sen-
sor Ground) may be open.
1 Connect the OBD II scan tool or TOYOTA hand −held tester and read the throttle
valve opening percentage.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand−held tester to DLC3.
(c) Turn ignition switch ON and push the OBD II scan tool or TOYOTA hand−held tester main switch ON.
CHECK:
Read the throttle valve opening percentage.
OK:
Throttle valveThrottle valve opening positionexpressed as percentage
Fully openApprox. 75 %
Fully closedApprox. 10 %
OK Check for intermittent problems (See page DI−3 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−42
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Connect the OBD II scan tool or TOYOTA hand −held tester and read value for
voltage output of heated oxygen sensor).
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(c) Warm up engine to normal operating temp.
CHECK:
Read voltage output of heated oxygen sensor (bank 1 sensor 1) when eng\
ine is suddenly raced.
HINT:
Perform quick racing to 4,000 rpm 3 times using accelerator pedal.
OK:
Heated oxygen sensor (bank 1 sensor 1) output a RICH signal (0.45 V o\
r more) at least once.
OK Check and replace ECM (See page IN−28 ).
NG
2 Check for open and short in harness and connector between ECM and heated\
oxygen sensor (bank1 sensor 1) (See page IN−28 ).
NG Repair or replace harness or connector.
OK
Replace heated oxygen sensor
(bank 1 sensor 1).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−44
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check for open and short in harness and connector between ECM and heated
oxygen sensor (bank 1 sensor 1) (See page IN−28 ).
NG Repair or replace harness or connector
(See page IN−28 ).
OK
2 Check for heated oxygen sensor (bank 1 sensor 1) data.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(c) Warm up engine to normal operating temp.
CHECK:
Read the heated oxygen sensor (bank 1 sensor 1) output voltage and sho\
rt −term fuel trim.
RESULT:
PatternHeated o xygen sensor (bank 1 sensor 1) output voltageShort−term fuel trim
1Lean condition (Changes at 0.55 V or less)Changes at about +20 %
2Rich condition (Changes at 0.4 V or more)Changes at about −20 %
3Except 1 and 2
1, 2 Check fuel trim system (See page DI−51 ).
3
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00168
ON
EGR Gas Temp.
Sensor ECM
19 9
1
2
BE6653
FI7055 THG
E2
E4
E5 5V
−
DIAGNOSTICS ENGINE
DI−71
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
TOYOTA hand −held tester
1 Connect the TOYOTA hand −held tester and read value of EGR gas temp. value.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and push the TOYOTA hand −held tester main switch ON.
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: 10° C (50°F) or more
HINT:
If there is and open circuit, the TOYOTA hand−held tester indicates 3.1 °C (37.6° F).
OK Go to step 4.
NG
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect the EGR gas temp. sensor connector.
(b) Connect sensor wire harness terminals together.
(c) Turn ignition switch ON.
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: Approx. 157.5° C (315.5°F)
OK Confirm good connection at sensor. If OK, replace EGR gas temp. sensor.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−80
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC P0402 Exhaust Gas Recirculation Flow Excessive Detected
CIRCUIT DESCRIPTION
Refer to DTC P0401 (Exhaust Gas Recirculation Flow Insufficient Detected) on page DI−69.
DTC No.DTC Detecting ConditionTrouble Area
P0402
EGR gas temp. sensor value is high during EGR cut −off when
engine is cold (Race engine at about 4,000 rpm without load so
that vacuum is applied to port E)
(2 trip detection logic) EGR valve stuck open
 EGR VSV open malfunction
 Open in VSV circuit for EGR
 Short in EGR gas temp. sensor circuit
 ECM
EGR valve is always open (2 trip detection logic)
Refer to DTC P0401 (Exhaust Gas Recirculation Flow Insufficient Detected) for the System Check Driving
Pattern and Wiring Diagram.
INSPECTION PROCEDURE
TOYOTA hand −held tester
1 Connect the TOYOTA hand −held tester and read EGR gas temp. value.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and push the TOYOTA hand −held tester main switch ON.
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: 150° C (302°F) or less (Not immediately after driving)
HINT:
If there is a short circuit, the TOYOTA hand−held tester indicates Approx. 157.5°C (315.5°F).
OK Go to step 4.
NG
DI5PL−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−93
1996 LAND CRUISER (RM451U)
DTC P0510 Closed Throttle Position Switch Malfunction
CIRCUIT DESCRIPTION
Refer to DTC P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit \
Malfunction) on page DI−35.
DTC No.DTC Detecting ConditionTrouble Area
P0510
The closed throttle position switch does not turn ON or OFF
even once when the vehicle is driven
(2 trip detection logic)Open or short in closed throttle position switch circuit
 Closed throttle position switch
 ECM
HINT:
After confirming DTC P0510 use the TOYOTA hand−held tester to confirm the closed throttle position switch
signal from ”CURRENT DATA”.
Throttle ValveClosed Throttle Position Switch SignalMalfunction
Fully closedOFFOpen circuit
Fully openONShort circuit
WIRING DIAGRAM
Refer to DTC P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction) on page DI−35 for WIR-
ING DIAGRAM.
INSPECTION PROCEDURE
HINT:
If DTCs P0110 (Intake Air Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction),
P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction)\
are output simultaneously, E2 (Sen-
sor Ground) may be open.
TOYOTA hand −held tester
1 Connect the TOYOTA hand −held tester and read CTP switch signal.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and OBD II scan tool or TOYOTA hand−held tester main switch ON.
CHECK:
Read CTP switch signal on TOYOTA hand −held tester.
RESULT:
Throttle ValveClosed Throttle Position Switch SignalMalfunction
Fully closedOFFOpen circuit: Go to step 2
Fully openONShort circuit: Go to step 4
DI5PP−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010