1996 TOYOTA LAND CRUISER Fuse spec

Q08584
ECM
Pattern Select Switch*
(PWR Mode Switch)
PWR
E7
P−B
B−W
PWR Indicator Light
(Combination Meter)
ID2
63
C12
13
16
20
15
B
J6
EGU−IG
Fuse Block
Ignition Switch
EA2
AM1
IG1
Fuse Block
AM1
P−B
P−B
6 B
B B ID2
B−W
B−W
3
1
B−Y
2
4
222
1 FL AM1
F6
Battery
2
2
3
4
WB −L
R/B No. 2
R/B No. 2
Pattern Select Switch (PWR Mode Switch)
When the PWR mode switch is pushed in, the switch is contacted and
the PWR mode is celected.
To cancel the PWR mode, push the PWR mode switch onec again.
*:
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−179
1996 LAND CRUISER (RM451U)
Pattern Select Switch Circuit (PWR Mode Switch)
CIRCUIT DESCRIPTION
The ECM memory contains the shift programs for the NORMAL and POWER pattern\
s, 2 position, L position
and the lock −up patterns. Following the programs corresponding to the signals from th\
e pattern select
switch, the park/neutral position switch and other various sensors, the ECM swi\
tches the solenoid valves
ON and OFF, and control the transmission gear change and the lock −up clutch operation.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check operation of PWR indicator light.
PREPARATION:
Check if the PWR indicator light normally when the PWR mode switch is set to NORM and PWR position.
NG Check and repair PWR indicator light.
OK
DI5L6−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE3840
Q08229D00094
PWR
ON
DI−180
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
2 Check PATTERN SEL SW signal.
When using TOYOTA hand −held tester:
PREPARATION:
(a) Remove the fuse box cover.
(b) Connect a TOYOTA hand−held tester to the DLC3.
(c) Turn the ignition switch ON and TOYOTA hand−held tes-
ter main switch ON.
CHECK:
Read the PWR signal on the TOYOTA hand −held tester.
OK:
PWR Mode SwitchPATTERN SEL SW Signal
PWRON
NORMOFF
When not using TOYOTA hand −held tester:
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between terminal PWR of the ECM con-
nector and body ground when the PWR mode switch is set to
the PWR (POWER) position and NORM (NORMAL) position.
OK:
PWR Mode SwitchVoltage
PWR7.5 − 14 V
NORMBelow 1.5 V
HINT:
The ECM uses the normal pattern signal if the power signal is
not input.
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−147 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−226
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Is DTC output?
Check DTC on page DI−190 .
YES Repair circuit indicated by code output.
NO
2 Is normal code displayed?
YES Check ABS solenoid relay. Check for short in harness and connector between ABS solenoid
relay and DLC1 (See page IN−28 ).
NO
3 Is ABS warning light go off?
YES Check for open or short in harness and connec-
tor between ECU−IG fuse and ECU (See page
IN−28 ).
NO
4 Check battery positive voltage.
PREPARATION:
Start the engine.
CHECK:
Check the battery positive voltage.
OK:
Voltage: 10 − 16 V NG Check and repair charging system.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N14677
Fuse
DI−276
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
SRS Warning Light System Malfunction (Does not light up, when
ignition switch is turned to ACC or ON.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the \
ignition switch is
turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to\
inform the driver of the abnormality.
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking\
of the SRS warn-
ing light.
WIRING DIAGRAM
Refer to page DI−274 for the WIRING DIAGRAM.
INSPECTION PROCEDURE
1 Check ECU−B Fuse.
PREPARATION:
Remove ECU−B fuse.
CHECK:
Check continuity of ECU −B fuse.
OK:
Continuity
HINT:
Fuse may be burnt out even if it appears to be OK during
visual inspection.
If fuse is OK, install it.
NG Go to step 5.
OK
2 Preparation. (See step 1 on page DI−271)
DI5QE−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE4032
BE4033I00021
Normal Code
0.25 sec.
0.25 sec.
ON
OFF
ON
OFF
4 sec. 1.5 sec.
0.5 sec.
2.5 sec.0.5 sec.1.5 sec.
Malfunction codes 11 and 21
Code 11 Code 21
N09348
TOYOTA hand-held tester
TOYOTA Break-out-box
N18670
Instrument Panel Junction Block ECU- B
Fuse
DI-287
-
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
HINT:
If the DTC is not output, inspect the diagnosis circuit (See page
DI-333 )
As an example, the blinking patterns for codes; normal, 11 and
21 are shown in the illustration.
2. ECU TERMINAL VALUES MEASUREMENT BY USING TOYOTA BREAK-OUT-BOX AND TOYOTA HAND-
HELD TESTER
(a) Hook up the TOYOTA break- out- box and TOYOTA hand-held tester to the vehicle.
(b) Read the ECU input/output values by following the prompts on the tester screen.
(c) Please refer to the TOYOTA hand-held tester has a ºSnapshotº function. This records the measured data and
is effective in the diagnosis of intermittent problems.
3. DTC CLEARANCE
(a) After completing repairs, the diagnostic trouble code re- tained in memory can be cleared by removing the ECU-B
fuse for 10 seconds or more, with the ignition switch off.
(b) Check that the normal code is displayed after connecting the fuse.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5O7−02
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−291
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, check the circuit listed for that cod\
e in the table
below and proceed to the appropriate page.
DTC No.
(See Page)Circuit inspectionTrouble Area
11
( DI−296 )Actuator Motor Circuit
Actuator motor
 Harness or connector between cruise control ECU and
actuator motor
 Cruise control ECU
12
( DI−298 )Actuator Magnetic Clutch Circuit
STOP Fuse
 Stop light switch
 Actuator magnetic clutch
 Harness or connector between cruise control ECU and
actuator magnetic clutch, actuator magnetic clutch and body
ground
 Cruise control ECU
13
( DI−301 )Actuator Position Sensor Circuit
Actuator position sensor
 Harness or connector between cruise control ECU and
actuator position sensor
 Cruise control ECU
14
( DI−304 )Actuator Mechanical Malfunction
Actuator motor (actuator lock: motor, arm)
 Harness or connector between cruise control ECU and
actuator motor
 Cruise control ECU
21
( DI−306 )Open in Vehicle Speed Sensor Circuit
Combination meter
 Harness or connector between cruise control ECU and com-
bination meter, combination meter and vehicle speed sensor
 Vehicle speed sensor
 Cruise control ECU
23
( DI−310 )Vehicle Speed Signal AbnormalVehicle speed sensor
 Cruise control ECU
32
( DI−311 )Control Switch Circuit
Cruise control switch
 Harness or connector between cruise control ECU and cruise
control switch, cruise control switch and body ground
 Cruise control ECU
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N18670
Instrument Panel Fuse Block
STOP Fuse
I00133
1
2
43
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−299
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check STOP fuse.
PREPARATION:
(a) Turn ignition switch OFF.
(b) Remove the STOP fuse from instrument panel fuse block.
CHECK:
Check fuse continuity.
OK:
There is continuity.
NG Replace STOP fuse.
OK
2 Check stop light switch.
PREPARATION:
Disconnect the stop light switch connector.
CHECK:
Check continuity between terminals.
Switch positionContinuity
Switch pin free
(Brake pedal depressed)1 − 2
Switch pin pushed in
(Brake pedal released)3 − 4
NG Replace stop light switch.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Input SignalIndicator Light
Blinking Pattern
Stop Light
switch ON
Light ON
OFF SW OFF
SW ON
DI−314
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Stop Light Switch Circuit
CIRCUIT DESCRIPTION
When the brake pedal is depressed, the stop light switch sends a signal to th\
e ECU. When the ECU receives
this signal, it cancels the cruise control.
A fail− safe function is provided so that the cancel functions normally , even if there is a malfunction in the stop
light signal circuit.
The cancel conditions are: Battery positive voltage at terminal STP −
When the brake is on, battery positive voltage normally applies through the S\
TOP fuse and stop light switch
to terminal STP− of the ECU, and the ECU turns the cruise control off.
If the harness connected to terminal STP − has an open circuit, terminal STP − will have battery positive volt-
age and the cruise control will be turned off.
Also, when the brake is on, the magnetic clutch circuit is cut mechanically \
by the stop light switch, turning
the cruise control off (See page DI−298 for operation of the magnetic clutch).
WIRING DIAGRAM
See page DI−298 .
INSPECTION PROCEDURE
1 Check operation of stop light.
CHECK:
Check that stop light comes on when brake pedal is depressed, and turns off when brake pedal is released.
NG Check stop light system (See page BE−24 ).
OK
2 Input signal check.
CHECK:
(a) See input signal check on DI−286.
(b) Check the indicator light when the brake pedal is de-
pressed.
OK:
The indicator light goes off when the brake pedal is
depressed.
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−295 ).
NG
DI5OI−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010