1996 TOYOTA LAND CRUISER BAT

SF06G−11
P05668
OhmmeterContinuity
No Continuity Ohmmeter
1
2
43
P05667
Ohmmeter Continuity
Battery
1
2
4 3
SF−54
−
SFI EFI MAIN RELAY
682
Author: Date:
1996 LAND CRUISER (RM451U)
EFI MAIN RELAY
INSPECTION
1. REMOVE EFI MAIN RELAY
LOCATION: In the engine compartment relay box.
2. INSPECT EFI MAIN RELAY CONTINUITY
(a) Using an ohmmeter, check that there is continuity be-
tween terminals 1 and 3.
(b) Check that there is no continuity between terminals 2 and
4.
If continuity is not as specified, replace the relay.
3. INSPECT EFI MAIN RELAY OPERATION
(a) Apply battery voltage across terminals 1 and 3.
(b) Using an ohmmeter, check that there is continuity be-
tween terminals 2 and 4.
If operation is not as specified, replace the relay.
4. REINSTALL EFI MAIN RELAY
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1F5−01
P05668
OhmmeterContinuity
Ohmmeter
No Continuity
1
2
43
P05667
Ohmmeter 1
2
3
4 Battery
SF−56
−
SFI CIRCUIT OPENING RELAY
1996 LAND CRUISER (RM451U)
INSPECTION
1. REMOVE CIRCUIT OPENING RELAY
2. INSPECT CIRCUIT OPENING RELAY CONTINUITY
(a) Using an ohmmeter, check that there is continuity be- tween terminals 1 and 3.
(b) Check that there is no continuity between terminals 2 and
4.
If continuity is not as specified, replace the relay.
3. INSPECT CIRCUIT OPENING RELAY OPERATION
(a) Apply battery voltage across terminals 1 and 3.
(b) Using an ohmmeter, check that there is continuity be- tween terminals 2 and 4.
If operation is not as specified, replace the relay.
4. REINSTALL CIRCUIT OPENING RELAY
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1F7−01
P09134
OhmmeterContinuity
Ohmmeter Ohmmeter
Continuity
No Continuity FP
PR
FPR
+B1
+B2
P09135
Ohmmeter
No
Continuity
Battery
Ohmmeter
Continuity +B1
+B2 FP
PR
FPR
−
SFI FUEL PUMP RELAY
SF−57
685
Author: Date:
1996 LAND CRUISER (RM451U)
FUEL PUMP RELAY
INSPECTION
1. REMOVE FUEL PUMP RELAY
(a) Disconnect the fuel pump relay connector.
(b) Remove the bolt and fuel pump relay.
2. INSPECT FUEL PUMP RELAY CONTINUITY
(a) Using an ohmmeter, check that there is continuity be-
tween terminals +B1 and FPR.
(b) Check that there is continuity between terminals +B2 and
FP.
(c) Check that there is no continuity between terminals +B2
and PR.
If continuity is not as specified, replace the relay.
3. INSPECT FUEL PUMP RELAY OPERATION
(a) Apply battery voltage across terminals +B1 and FPR.
(b) Using an ohmmeter, check that there is no continuity be- tween the +B2 and FP.
(c) Check that there is continuity between terminals +B2 and
PR.
If operation is not as specified, replace the relay.
4. REINSTALL FUEL PUMP RELAY
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1F9−01
−
SFI VSV FOR FUEL PRESSURE CONTROL
SF−59
687
Author: Date:
1996 LAND CRUISER (RM451U)
VSV FOR FUEL PRESSURE
CONTROL
INSPECTION
1. REMOVE AIR INTAKE CHAMBER (See page EM−28 )
2. DISCONNECT VACUUM HOSES AND CONNECTOR
3. INSPECT VSV FOR OPEN CIRCUIT
Using an ohmmeter, check that there is continuity between the
terminals. Resistance: 37 − 44 Ω at 20° C (68°F)
If there is no continuity, replace the VSV.
4. INSPECT VSV FOR GROUND
Using an ohmmeter, check that there is no continuity between
each terminal and the body.
If there is continuity, replace the VSV.
5. INSPECT VSV OPERATION
(a) Check that the air flows from pipe E to pipe G.
(b) Apply battery voltage across the terminals.
(c) Check that the air does not flows from pipe E to the filter.
If operation is not as specified, replace the VSV.
6. RECONNECT VACUUM HOSES AND CONNECTOR
7. REINSTALL AIR INTAKE CHAMBER (See page EM−54 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1F2−04
−
SERVICE SPECIFICATIONS CHARGING
SS−21
144
Author: Date:
1996 LAND CRUISER (RM451U)
CHARGING
SERVICE DATA
BatteryVoltage at 20°C (68° F)12.7 − 12.9
Drive beltTension New belt
Used belt400 − 580 N (41.0 − 59.1 kgf, 90.4 − 130.2 lbf)
200 − 390 N (20.4 − 40.0 kgf, 45.0 − 88.2 lbf)
GeneratorRated output
Rotor coil resistance at 20 °C (68° F)
Slip ring diameter STD Minimum
Brush exposed length STD
Minimum12 V 80 A
2.8 − 3.0 Ω
14.2 − 14.4 mm (0.559 − 0.567 in.)
12.8 mm (0.504 in.)
10.5 mm (0.413 in.)
1.5 mm (0.059 in.)
Voltage regulatorRegulating voltage at 25°C (77° F)
at 115 °C (239° F)14.0 − 15.1 V
13.5 − 14.3 V
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

ST08H−03
P23047
Terminal CBattery
Terminal 50
P23049
Disconnect
Battery
P23048
DIsconnect
Battery
P23050
Terminal 30 AmmeterBattery
Terminal 50
ST−16
−
STARTING STARTER
1996 LAND CRUISER (RM451U)
TEST
NOTICE:
These tests must be performed within 3 to 5 seconds to
avoid burning out the coil.
1. DO PULL−IN TEST
(a) Disconnect the field coil lead wire from terminal C.
(b) Connect the battery to the magnetic switch as shown.
Check that the clutch pinion gear moves outward.
2. DO HOLD−IN TEST
With battery connected as above with the clutch pinion gear
out, disconnect the negative ( −) lead from terminal C. Check
that the pinion gear remains out.
3. INSPECT CLUTCH PINION GEAR RETURN
(a) Disconnect the negative ( −) lead from the switch body.
(b) Check that the clutch pinion gear returns inward.
4. DO NO−LOAD PERFORMANCE TEST
(a) Connect the battery and ammeter to the starter as shown.
(b) Check that the starter rotates smoothly and steadily with
the pinion gear moving out. Check that the ammeter
shows the specified current.
Specified current:
1.4 kW type
At 11.5V: 90 A or less
2.0 kW type
At 11.5V: 100 A or less
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q02622
Light upGoes off
L
NH
DIFF LOCK
DIFF LOCK
TR0BM−03
Z15367
Relay Side
V01699
V06651
−
TRANSFER MOTOR SHIFT CONTROL SYSTEM
TR−37
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SHIFT LEVER POSITION
(a) Start the engine, and turn the center diff lock switch to
OFF.
(b) Check that the center diff indicator light comes on when the transfer shift lever shifted to the ”L” position. Check
that the light goes off when the lever is shifted to the ”N”
or ”H” position.
2. INSPECT CENTER DIFF LOCK CONTROL RELAY
(a) Check that there is continuity between the terminals, as shown in the chart.
HINT:
There is a diode between the terminals 6 and 7. If the circuit
shown no continuity, change the positive (+) and negative ( −)
probes and recheck the circuit.
(b) Apply battery positive voltage between the terminals and check that there is continuity between the terminals, as
shown in the chart.
If continuity is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010