1996 TOYOTA LAND CRUISER lock

R05896
AB0118
R13006AB0119
W02042
H00007
Spiral
Cable
P Squib
D Squib
ACC ON
or
DLC1 Code 11
E1 Tc Airbag
Sensor
Assembly
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−251
1996 LAND CRUISER (RM451U)
5 Check D squib.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative ( −) terminal cable from the battery,
and wait at least 90 seconds.
(c) Connect steering wheel pad connector.
(d) Connect negative ( −) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory. (See page DI−240 )
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 11 is not output.
HINT:
Codes other than code 11 may be output at this time, but they
are not relevant to this check.
NG Replace steering wheel pad.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R05897
AB0118
R13006AB0119
W02042
H00008
Airbag
Sensor
Assembly
Spiral
Cable
P Squib
D Squib ACC ON
or
DLC1
E1 Tc Code 11
DI−252
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
6 Check P squib.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative ( −) terminal cable from the battery,
and wait at least 90 seconds.
(c) Connect front passenger airbag assembly connector.
(d) Connect negative ( −) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory. (See page DI−240 )
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 11 is not output.
HINT:
Codes other than code 11 may be output at this time, but they
are not relevant to this check.
NG Replace front passenger airbag assembly.
OK
From the results of the above inspection, the malfunctioning part can now be \
considered normal.
To make sure of this, use the simulation method to check.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AB0069
AB0069
AB0118
R13006AB0119W01933
W02043 H00012
Airbag Sensor
Assembly
P+
P−
Spiral
Cable
P Squib
D Squib D− D+ ACC ON
or
DLC1 Code 12
E1 Tc
DI−256
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
4 Check airbag sensor assembly.
PREPARATION:
(a) Connect connector to airbag sensor assembly.
(b) Using a service wire, connect D
+ and D− on spiral cable
side of connector between spiral cable and steering
wheel pad.
(c) Using a service wire, connect P
+ and P− on airbag sensor
assembly side of connector between airbag sensor as-
sembly and front passenger airbag assembly.
(d) Connect negative ( −) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory. (See page DI−240 )
(c) Turn ignition switch to LOCK, and wait at least 20 se- conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1. SST 09843−18020
(f) Check DTC.
OK:
DTC 12 is not output.
HINT:
Codes other than code 12 may be output at this time, but they
are not relevant to this check.
NG Replace airbag sensor assembly.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R13006 R05896
AB0118 AB0019W02043H00013
Airbag
Sensor
Assembly
P Squib
D Squib Spiral
Cable
ACC ON
or
DLC1 Code 12
E1 Tc
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−257
1996 LAND CRUISER (RM451U)
5 Check D squib.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative ( −) terminal cable from the battery,
and wait at least 90 seconds.
(c) Connect steering wheel pad connector.
(d) Connect negative ( −) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory. (See page DI−240 )
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 12 is not output.
HINT:
Codes other than code 12 may be output at this time, but they
are not relevant to this check.
NG Replace steering wheel pad.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R05897
R13006 AB0118AB0119
W02043 H00014
Airbag
Sensor
Assembly
P Squib
D Squib Spiral
Cable
ACC ON
or
DLC1 Code 12
E1 Tc
DI−258
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
6 Check P squib.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative ( −) terminal cable from the battery,
and wait at least 90 seconds.
(c) Connect front passenger airbag assembly connector.
(d) Connect negative ( −) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory. (See page DI−240 )
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 12 is not output.
HINT:
Codes other than code 12 may be output at this time, but they
are not relevant to this check.
NG Replace front passenger airbag assembly.
OK
From the results of the above inspection, the malfunctioning part can now be \
considered normal.
To make sure of this, use the simulation method to check.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R05899
AB0119
R14288
H00015
Airbag Sensor
Assembly
P Squib
D Squib Spiral
Cable
D+
(+)(−) ON
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−259
1996 LAND CRUISER (RM451U)
7 Check spiral cable.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect connector between airbag sensor assembly
and spiral cable.
(c) Turn ignition switch ON.
CHECK:
Measure voltage at D+ on spiral cable side of connector be-
tween spiral cable and steering wheel pad and body ground.
OK:
Voltage: 0 V
NG Repair or replace spiral cable.
OK
Repair or replace harness or connector between airbag sensor assembly an\
d spiral cable.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R05895
AB0118
R13006AB0069
AB0119
W02044
H00017
Airbag
Sensor
Assembly
Spiral
Cable
D Squib P Squib
D+
D− ACC
ON
or
DLC1
E1 Tc Code 14
DI−262
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
3 Check airbag sensor assembly.
PREPARATION:
(a) Connect connector to airbag sensor assembly.
(b) Using a service wire, connect D+ and D− on spiral cable
side of connector between spiral cable and steering
wheel pad.
(c) Connect negative ( −) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory. (See page DI−240 )
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 14 is not output.
HINT:
Codes other than code 14 may be output at this time, but they
are not relevant to this check.
NG Replace airbag sensor assembly.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R05896
AB0118
R13006AB0119
W02044
H00018
Airbag Sensor
Assembly
Spiral
Cable
P Squib
D Squib
ACC ON
or
DLC1
E1 Tc Code 14
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−263
1996 LAND CRUISER (RM451U)
4 Check D squib.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative ( −) terminal cable from the battery,
and wait at least 90 seconds.
(c) Connect steering wheel pad (squib) connector.
(d) Connect negative ( −) terminal cable to battery, and wait
at least 2 seconds.
CHECK:
(a) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(b) Clear malfunction code stored in memory. (See page DI−240 )
(c) Turn ignition switch to LOCK, and wait at least 20 se-
conds.
(d) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(e) Using SST, connect terminals Tc and E1 of DLC1.
SST 09843−18020
(f) Check DTC.
OK:
DTC 14 is not output.
HINT:
Codes other than code 14 may be output at this time, but they
are not relevant to this check.
NG Replace steering wheel pad.
OK
From the results of the above inspection, the malfunctioning part can now be \
considered normal.
To make sure of this, use the simulation method to check.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010