1996 TOYOTA LAND CRUISER transfer case

Q07126
FIPG
Q08404
FIPG
A
−
TRANSFER TRANSFER ASSEMBLY
TR−7
1996 LAND CRUISER (RM451U)
Thickness:
Dimension C + (0. 014 − 0.039 mm, 0.0006 − 0.0015 in.)
(i) From the following table, select a shim so that its thick-
ness is within the range of the calculation.
MarkThickness mm (in.)MarkThickness mm (in.)
B0.30 (0.0118)H1.80 (0.0709)
C0.45 (0.0177)J2.00 (0.0787)
D1.00 (0.0394)K2.20 (0.0866)
E1.20 (0.0472)L2.40 (0.0945)
F1.40 (0.0551)M2.60 (0.1024)
G1.60 (0.0630)N0.55 (0.0216)
13. REMOVE OIL STRAINER FROM REAR CASE
Remove the 2 set bolts and oil strainer.Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)
14. REMOVE CASE COVER
(a) Remove the 5 bolts.
HINT:
At the time of reassembly, apply liquid sealer to the bolt threads.
Sealant: Part No.08833−00080, THREE BOND 1344,
LOCTITE 242 or equivalent
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
(b) Using a brass bar and hammer, tap the case cover and remove it.
HINT:
At the time of reassembly, apply FIPG to the rear case. FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
15. SEPARATE FRONT CASE AND REAR CASE
(a) Using a snap ring expander, remove the snap ring from the rear case.
(b) Remove the 8 bolts.
HINT:
At the time of reassembly, apply liquid sealer to the ”A” bolt
threads. Sealant: Part No.08833 −00080, THREE BOND 1344,
LOCTITE 242 or equivalent
Torque:37 N·m (380 kgf·cm, 27 ft·lbf)
(c) Using a brass bar and hammer, tap the rear case and sep-
arate it.
HINT:
At the time of reassembly, apply FIPG to the front case.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TF0854
TF0986
TF0857
Q07130
RemovalInstallation
Socket Wrench Socket Wrench
TR−8
−
TRANSFER TRANSFER ASSEMBLY
1996 LAND CRUISER (RM451U)
FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
16. REMOVE 2 BEARING RACES FROM REAR CASE
17. REMOVE INPUT SHAFT ASSEMBLY
Using a plastic hammer, remove the input shaft assembly.
18. REMOVE IDLER GEAR ASSEMBLY, CENTER DIFFER-
ENTIAL ASSEMBLY, SHIFT FORK NO.1 AND SHIFT
FORK NO.1 SHAFT FROM FRONT CASE
19. SEPARATE SHIFT FORK NO.1 AND SHIFT FORK NO.1 SHAFT
(a) Using a pin punch and hammer, drive out the slotted spring pin.
(b) Separate the shift fork No.1 and shift fork No.1 shaft.
20. REMOVE SHIFT OUTER LEVER AND INNER LEVER
(a) Remove the nut and washer from the shift outer lever. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
(b) Using a brass bar, hammer and socket wrench, tap out the lever lock pin.
(c) Remove the shift outer lever, washer and inner lever from
the front case.
21. REMOVE OIL RECEIVER FROM FRONT CASE
Remove the bolt and oil receiver. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07131
SST
TF0867
I19645
Push
Free
−
TRANSFER TRANSFER ASSEMBLY
TR−9
1996 LAND CRUISER (RM451U)
22. REMOVE 2 BEARING RACES FROM FRONT CASE
(a) Using SST, remove the bearing race (for idler gear).
SST 09950−40010, 09950 −60010 (09951−00320)
HINT:
At the time of reassembly, please refer to the following item.
Using SST and a press, install the bearing race (for idler gear).
SST 09316−60011 (09316 −00011, 09316−00041)
(b) Using a brass bar and hammer, remove the bearing race
(for output shaft).
HINT:
At the time of reassembly, please refer to the following item.
Using SST and a press, install the bearing race (for the out put
shaft). SST 09316 −20011, 09316 −60011 (09316 −00011,
09316 −00031)
23. INSPECT TRANSFER INDICATOR SWITCH
Check that there is continuity between the terminals, as shown.
Switch PositionSpecified
PushContinuity
FreeNo continuity
If continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BB−01
Q07134
Front Drive Gear
PieceHigh
Speed Output GearHigh Speed Output
Gear Bushing
Clutch HubHigh and Low
Clutch Sleeve Rear Taper Roller
Bearing
 Snap Ring
Needle Roller Bearing
Thrust Washer
Thrust Washer Rear Side Gear
Straight Pin x 12
Differential Rear Case
Thrust Washer
Pinion
Gear
Pinion Shaft
Front Side Gear
Thrust Washer
Differential Front Case
 Non− reusable part Low Gear
Straight Pin

Snap Ring Front T
aper Roller BearingNeedle Roller Bearing
Pinion Gear
TR−18
−
TRANSFER CENTER DIFFERENTIAL
828
Author: Date:
1996 LAND CRUISER (RM451U)
CENTER DIFFERENTIAL
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BC−01
TF0900
TF0944
Q07101
SST
Q07102
SST
Q07103
SST
−
TRANSFER CENTER DIFFERENTIAL
TR−19
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. INSPECT HIGH SPEED OUTPUT GEAR RADIAL AND
THRUST CLEARANCE
(a) Using a feeler gauge, measure the high speed output gear thrust clearance.
Standard clearance:
0.10−0.25 mm (0.0039 −0.0098 in.)
Maximum clearance:
0.25 mm (0.0098 in.)
(b) Using a dial indicator, measure the high speed output gear radial clearance.
Standard clearance:
0.035−0.091 mm (0.0014 −0.0036 in.)
Maximum clearance:
0.091 mm (0.0036 in.)
2. REMOVE FRONT DRIVE GEAR PIECE
(a) Using a snap ring expander, remove the snap ring.
(b) Using SST and a press, remove the front drive gear piece.
SST 09950−00020, 09950 −60010 (09951−00320)
NOTICE:
Be careful not to drop the center differential assembly.
3. REMOVE FRONT TAPER ROLLER BEARING
Using SST and a press, remove the front taper roller bearing.
SST 09950−00020
4. REMOVE HIGH SPEED OUTPUT GEAR
5. REMOVE NEEDLE ROLLER BEARING
6. REMOVE HIGH AND LOW CLUTCH SLEEVE AS-
SEMBLY
7. REMOVE HIGH SPEED OUTPUT GEAR BUSHING AND CLUTCH HUB
(a) Using SST and a press, remove the high speed output
gear bushing and clutch hub.
SST 09550−00020, 09950 −00030, 09950−60010
(09951 −00320)
(b) Using a magnetic finger, remove the straight pin from the
differential front case.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07113
SST
Q07114
SST
SST
Bearing
TR−20
−
TRANSFER CENTER DIFFERENTIAL
1996 LAND CRUISER (RM451U)
8. REMOVE REAR TAPER ROLLER BEARING
Using SST and a press, remove the rear taper roller bearing.
SST 09950−00020, 09950 −60010 (09951−00320)
9. REMOVE DIFFERENTIAL REAR CASE
Remove the 12 bolts and differential rear case.
10. REMOVE REAR SIDE GEAR AND THRUST WASHER
11. REMOVE PINION SHAFT, PINION GEAR AND THRUST
WASHER
(a) Remove the straight pin from the pinion shaft.
(b) Remove the pinion shaft, 2 pinion gears and thrust wash-
ers.
(c) Remove the front side gear and thrust washer.
12. REMOVE LOW GEAR
Using a plastic hammer, tap and remove the low gear.
NOTICE:
Be careful not to damage the low gear.
13. REMOVE NEEDLE ROLLER BEARING
(a) Using a screwdriver, remove the snap ring.
(b) Using SST and a hammer, remove the needle roller bear-
ing from the differential rear case.
SST 09223 −00010, 09950 −60010 (09951 −00400),
09950 −70010 (09951 −07150)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BD−01
Q07115
SSTStamp
TF1012
TF0913
TF0917
−
TRANSFER CENTER DIFFERENTIAL
TR−21
1996 LAND CRUISER (RM451U)
REASSEMBLY
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.
1. INSTALL NEEDLE ROLLER BEARING
(a) Using SST and a press, install the needle roller bearing
to the differential rear case.
SST 09612−24014 (09612 −10050)
HINT:
Install the bearing to the differential rear case, taking care that
its stamped side comes in contact with SST.
(b) Install the snap ring.
2. INSTALL LOW GEAR
(a) Clean the contact surface of the differential case.
(b) Heat the low gear in boiling water.
(c) Carefully remove the low gear from the water.
(d) After the moisture on the low gear has completely evapo- rated, quickly install the low gear to the differential case.
3. INSTALL PINION SHAFT, PINION GEAR AND THRUST
WASHER
(a) Install the front side gear and thrust washer to the differ- ential front case.
(b) Install the pinion shaft, 2 pinion gears and thrust washers
to the differential front case.
(c) Using a dial indicator, measure the front case backlash.
HINT:
Push the pinion shaft. Minimum backlash: 0.05 mm (0.0020 in.)
If the backlash is not within the specification, replace the thrust
washer with one of the correct size and reinstall the thrust wash-
er.
Thickness mm (in.)Thickness mm (in.)
1.70 (0.0669)2.45 (0.0965)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TF0920
Q00534
SST
Q00547
SST
Q00549
TR−22
−
TRANSFER CENTER DIFFERENTIAL
1996 LAND CRUISER (RM451U) 1.85 (0.0728)
2.60 (0.1024)
2.00 (0.0787)2.75 (0.1083)
2.15 (0.0846)2.90 (0.1
142)
2.30 (0.0906)3.05 (0.1201)
(d) In the same way, measure the rear case backlash.
4. INSTALL STRAIGHT PIN TO PINION SHAFT
5. INSTALL REAR SIDE GEAR AND THRUST WASHER
6. INSTALL DIFFERENTIAL REAR CASE
Install the differential rear case and 12 set bolts.
7. TORQUE REAR CASE SET BOLT
(a) Torque the rear case 12 set bolts.
Torque: 88 N·m (900 kgf·cm, 65 ft·lbf)
(b) Turn the pinion gear.
(c) Loosen the rear case 12 set bolts.
(d) Torque the rear case 12 set bolts. Torque: 98 N·m (1,000 kgf·cm, 72 ft·lbf)
8. INSTALL REAR TAPER ROLLER BEARING
Using SST and a press, install the rear taper roller bearing. SST 09316−12010
9. INSTALL CLUTCH HUB
Using SST and a press, install the clutch hub. SST 09316−12010, 09316 −60011 (09316−00011)
10. INSTALL HIGH SPEED OUTPUT GEAR BUSHING
(a) Apply MP grease to the straight pin.
(b) Install the straight pin, as shown.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010