Page 286 of 1399
BO38Q−01
BO−46
−
BODY WINDSHIELD
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE HOOD
2. REMOVE WIPER ARMS
3. REMOVE COWL LOUVER
4. REMOVE INNER REAR VIEW MIRROR
5. REMOVE PERSONAL LIGHT ASSEMBLY
6. REMOVE PERSONAL LIGHT COVER
7. REMOVE SUN VISORS AND HOLDERS
8. REMOVE ASSIST GRIPS
9. REMOVE FRONT PILLAR GARNISHES
10. LOOSEN ROOF HEADLINING
11. REMOVE WINDSHIELD GLASS
(a) From the outside of the vehicle , cut off the weatherstrip.
NOTICE:
Do not damage the body and the glass.
(b) Push piano wire through between the body and glass from the interior.
(c) Tie both wire ends to the wooden blocks or equivalent.
NOTICE:
When separating, take care not to damage the paint or inte-
rior ornaments.
To prevent scratching the safety pad when removing the
windshield, place a plastic sheet between the piano wire
and safety pad.
(d) Cut the adhesive by pulling the piano wire around it.
(e) Remove the glass.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 289 of 1399
−
BODY WINDSHIELD
BO−49
1996 LAND CRUISER (RM451U)
(b) Clean off the sealer oozing out from the masking tape with
a clean rag saturated in cleaner.
6. INSPECT FOR LEAKS AND REPAIR
(a) Do a leak test.
(b) Seal any leaks with auto glass sealer.
Part No. 08833−00030 or equivalent
7. INSTALL ROOF HEADLINING
8. INSTALL FRONT PILLAR GARNISHES
9. INSTALL ASSIST GRIPS
10. INSTALL SUN VISORS AND HOLDERS
11. INSTALL PERSONAL LIGHT COVER
12. INSTALL PERSONAL LIGHT ASSEMBLY
13. INSTALL INNER REAR VIEW MIRROR
14. INSTALL COWL LOUVER
15. INSTALL WIPER ARMS Torque: 20 N·m(205 kgf·cm, 15 ft·lbf)
16. INSTALL HOOD Torque: 18 N·m(185 kgf·cm, 13 ft·lbf)
17. ADJUST HOOD (See page BO−6)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 291 of 1399
BO38T−01
−
BODY QUARTER WINDOW GLASS
BO−51
1996 LAND CRUISER (RM451U)
REMOVAL
1. w/ No. 2 rear seat:
NO. 2 REAR SEAT
2. REMOVE BACK DOOR SCUFF PLATE
3. REMOVE QUARTER TRIM
4. REMOVE REAR SEAT SIDE GARNISH
5. REMOVE REAR DOOR SCUFF PLATE
6. REMOVE QUARTER PILLAR GARNISH
7. REMOVE REAR PILLAR GARNISH
8. REMOVE ASSIST GRIPS
9. LOOSEN ROOF HEADLINING
10. REMOVE VENT LOUVER AND QUARTER BELT MOULDING
(a) Remove the nut from the vent louver.
(b) Insert a screwdriver between the retainers and body to pry it loose.
HINT:
Tape the screwdriver tip before use.
(c) Pull out the vent louver.
(d) Pull out the clips from the edge of the panel, and remove the moulding.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 295 of 1399

BO38W−01
−
BODY QUARTER WINDOW GLASS
BO−55
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL WEATHERSTRIP ON GLASS
(a) Attach the weatherstrip to the glass.
NOTICE:
If the weatherstrip has hardened, it may develop leaks. Use
a new one if possible.
(b) Insert a cord into the groove of the weatherstrip all the way
around with the ends overlapping.
2. INSTALL QUARTER WINDOW GLASS
(a) Apply soapy water to contact surface of the weatherstrip lip and to the body flange.
HINT:
Begin installation in the middle of the lower part of the quarter
window glass.
(b) Hold the glass in position on the body.
(c) From the inside, pull on one cord at an angle so it pulls the
lip over the flange. From the outside, press the glass
along the weatherstrip until the glass is installed.
3. FIX IN GLASS
To make the glass fix snugly, tap from the outside with your
open hand.
4. INSPECT FOR LEAKS AND REPAIR
(a) Do a leak test.
(b) Seal any leak with auto glass sealer.
5. INSTALL ROOF HEADLINING
6. INSTALL ASSIST GRIPS
7. INSTALL REAR PILLAR GARNISH
8. INSTALL QUARTER PILLAR GARNISH
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 300 of 1399
BO390−01
BO−60
−
BODY SLIDING ROOF
1294
Author: Date:
1996 LAND CRUISER (RM451U)
SLIDING ROOF
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 301 of 1399
−
BODY SLIDING ROOF
BO−61
1295
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 302 of 1399
BO−62
−
BODY SLIDING ROOF
1296
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 303 of 1399
BO393−01
−
BODY SLIDING ROOF
BO−63
1996 LAND CRUISER (RM451U)
REMOVAL
HINT:
Tape the screwdriver tip before using to pry parts.
1. CHECK OPERATION TO THE SLIDING ROOF
2. REMOVE BACK DOOR SCUFF PLATE
3. w/ No. 2 Rear Seat
REMOVE NO. 2 REAR SEAT
4. REMOVE QUARTER TRIM RH
5. REMOVE QUARTER TRIM LH
6. REMOVE REAR SEAT SIDE GARNISH
7. REMOVE REAR DOOR SCUFF PLATE
8. REMOVE COWL SIDE TRIM
9. REMOVE FRONT AND REAR DOOR OPENING TRIM
10. REMOVE CENTER PILLAR LOWER GARNISH
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010