1996 TOYOTA LAND CRUISER Throttle position

DI−12
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
(b) TOYOTA Enhanced Signals.
TOYOTA hand−held tester displayMeasurement ItemNormal Condition*
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 2.0 − 3.5 ms
IAC STEP POSIntake Air Control Valve step position
Opening position step motor type IAC valveIdling: 10 − 50 step
STARTER SIGStarter SignalCranking: ON
CTP SWClosed Throttle Position Switch SignalThrottle Fully Closed: ON
A/C SIGA/C Switch SignalA/C ON: ON
PNP SWPark/Neutral Position Switch SignalP or N Position: ON
STOP LIGHT SWStop Light Switch SignalStop light switch ON: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL#1 − CYL#6Ratio of revolution variation for each cylinder
when variation is large0%
IGNITIONIgnition rate for all cylinders every 1,000 revolu-
tions0 − 3,000 rpm
EGRT GASEGR Gas Temp. Sensor V alueEGR not operating: Temp. between intake air
temp. and engine coolant temp.
EGR SYSTEMEGR System Operating ConditionIdling: OFF
FUEL PRES UP VSVFuel Pressure Up VSV SignalHigh temp. restarting: ON
FUEL PUMPFuel Pump SignalIdling: ON
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 − 1.2 V
O2 LR B1, S1
Oxygen Sensor Lean Rich Bank 1, Sensor 1
Response time for oxygen sensor output to
switch from lean to rich
Idling after warmed up: 0 − 1,000 msec.
O2 RL B1, S1
Oxygen Sensor Rich Lean Bank 1, Sensor 1
Response time for oxygen sensor output to
switch from rich to lean
Idling after warmed up: 0 − 1,000 msec.
∗: If no conditions are specifically stated for ”ldling”, it means t\
he shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OV−03
−
DIAGNOSTICS ENGINE
DI−13
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to \
the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, che\
ck the circuit for that code listed
in the table below. For details of each code, turn to the page referred to under the ’’See page ’’ for the respe-
cire ’’DTC No.’’ in the DTC chart.
DTC No.
(See Page)Detection ItemTrouble AreaMILMemory
P0100
( DI−20 )Mass Air Flow Circuit
MalfunctionOpen or short in mass air flow meter circuit
 Mass air flow meter
 ECM
 *1
P0101
( DI−25 )Mass Air Flow Circuit
Range/Performance
Problem
Mass air flow meter *1
P0110
( DI−26 )Intake Air Temp. Circuit
MalfunctionOpen or short in intake air temp. sensor circuit
 Intake air temp. sensor
 ECM
 *1
P0115
( DI−30 )Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
 Engine coolant temp. sensor
 ECM
 *1
P0116
( DI−34 )Engine Coolant Temp. Circuit
Range/Performance ProblemEngine coolant temp. sensor
 Cooling system *1
P0120
( DI−35 )Throttle/Pedal Position
Sensor/Switch ”A” Circuit
MalfunctionOpen or short in throttle position sensor circuit
 Throttle position sensor
 ECM
 *1
P0121
( DI−39 )Throttle/Pedal Position
Sensor/Switch ”A” Circuit
Range/Performance Problem
Throttle position sensor *1
P0125
( DI−40 )Insufficient Coolant Temp. for
Closed Loop Fuel Control Open or short in heated oxygen sensor circuit
 Heated oxygen sensor *1
P0130
( DI−43 )Heated Oxygen Sensor Circuit
Malfunction (Bank 1 Sensor 1)Heated oxygen sensor
 Fuel trim malfunction *1
P0133
( DI−46 ) Heated Oxygen Sensor Circuit
Slow Response
(Bank 1 Sensor 1)
Heated oxygen sensor *1
P0135
( DI−47 ) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 1)Open or short in heater circuit of heated oxygen sensor
 Heated oxygen sensor heater
 ECM
 *1
P0136
( DI−49 )Heated Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Heated oxygen sensor *1
P0141
( DI−47 ) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 2)
Same as DTC No. P0135 *1
*1: MIL lights up
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−15
1996 LAND CRUISER (RM451U)
DTC No.
(See Page)
Detection ItemTrouble Area*MILMemory
P0420
( DI−84 )Catalyst System Efficiency
Below Threshold Three− way catalytic convertor
 Open or short in heated oxygen sensor circuit
 Heated oxygen sensor

P0500
( DI−87 )Vehicle Speed Sensor
Malfunction
Combination meter
 Open or short in speed sensor circuit
 ECM
 Vehicle speed sensor

P0505
( DI−89 )Idle Control System
Malfunction
IAC valve is stuck or closed
 Open or short in IAC valve circuit
 Open or short A/C signal circuit
 Air intake (hose loose)

P0510
( DI−93 )Closed Throttle Position
Switch MalfunctionOpen in closed throttle position switch circuit
 Closed throttle position switch
 ECM

P1300
( DI−97 )Igniter Circuit Malfunction
Open or short in IGF or IGT circuit from igniter to ECM
 Igniter
 ECM

P1335
( DI−102 )Crankshaft Position Sensor
Circuit Malfunction
(during engine running)
Open or short in crankshaft position sensor circuit for NE sig-
nal
 Crankshaft position sensor for NE signal
 Starter
 ECM
−
P1500
( DI−103 )Stater signal circuit MalfunctionOpen or short in starter signal circuit
 ECM−
P1600
( DI−105 )ECM BATT MalfunctionOpen in back up power source circuit
 ECM
P1605
( DI−107 )Knock Control CPU MalfunctionECM
P1780
( DI−108 )Park/Neutral Position Switch
MalfunctionShort in park/neutral position switch circuit
 Park/neutral position switch
 ECM

*: −  MIL does not light up,   MIL lights up
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OX−03
FI6526
12345678910
11
1213
1415161718192021222324252612345678
910
11
1213141516 123456
78
910
11
12 12345678910
11
1415161718192021221213
E4 E5E6 E7
ECM Terminals
−
DIAGNOSTICS ENGINE
DI−17
1996 LAND CRUISER (RM451U)
TERMINALS OF ECM
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
BATT (E7 − 2) − E1 (E4 − 24)R − Y ↔ BR − BAlways9 − 14
+ B (E7 − 12) − E1 (E4 − 24)Y ↔ BR − BIG switch ON9 − 14
VCC (E5 − 1) − E2 (E5 − 9)R − G ↔ BR − BIG switch ON4.5 − 5.5
IDL (E5 − 11) − E2 (E5 − 9)G − W ↔ BR − B
IG switch ON and apply vacuum to the throttle opener
Throttle valve fully closed0 − 3
IG switch ON
Throttle valve fully open9 − 14
VTA (E5 − 10) − E2 (E5 − 9)G − B↔ BR − B
IG switch ON
Throttle valve fully closed0.3 − 0.8
IG switch ON
Throttle valve fully open3.2 − 4.9
VG (E5 − 2) − E21 (E5 − 16)G − BRIdling, N position, A/C switch OFF1.1 − 1.5
THA (E5 − 3) − E2 (E5 − 9)L − Y ↔ BR − BIdling, Intake air temp. 20° C (68° F)0.5 − 3.4
THW (E5 − 4) − E2 (E5 − 9) R − W↔BR − BIdling, Engine coolant temp. 80 °C (176°F)0.2 − 1.0
STA (E7 − 11) − E1 (E4 − 24)B − R ↔ BR − BCranking6.0 or more
#10 (E4 − 12) − E01 (E4 − 13)W − L ↔ BR
IG switch ON9 − 14
IdlingPulse generation
(See page DI−54)
#20 (E4 − 11) − E01 (E4 − 13)W − R ↔ BR
IG switch ON9 − 14
IdlingPulse generation
(See page DI−54)
#30 (E4 − 25) − E01 (E4 − 13)W − G ↔ BR
IG switch ON9 − 14
IdlingPulse generation
(See page DI−54)
#40 (E4 − 2) − E01 (E4 − 13)Y ↔ BR
IG switch ON9 − 14
IdlingPulse generation
(See page DI−54)
#50 (E4 − 1) − E01 (E4 − 13)Y − R ↔ BR
IG switch ON9 − 14
IdlingPulse generation
(See page DI−54)
#60 (E4 − 15) − E01 (E4 − 13)Y − L ↔ BR
IG switch ON9 − 14
IdlingPulse generation
(See page DI−54)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−25
1996 LAND CRUISER (RM451U)
DTC P0101 Mass Air Flow Circuit Range/Performance
Problem
CIRCUIT DESCRIPTION
Refer to DTC P0100 (Mass Air Flow Circuit Malfunction) on page DI−20.
DTC No.DTC Detecting ConditionTrouble Area
P0101
Conditions (a) and (b) continue with engine speed 900 rpm or
less (2 trip detection logic):
(a) Closed throttle position switch: ON
(b) Mass air flow meter output > 2.2 V
Mass air flow meterConditions (a) and (b) continue with engine speed 1500 rpm
(2 trip detection logic):
(a) Mass air flow meter output < 1 V
(b) VTA  0.72 V
WIRING DIAGRAM
Refer to DTC P0100 (Mass Air Flow Circuit Malfunction) on page DI−20 for the WIRING DIAGRAM.
INSPECTION PROCEDURE
1 Are there any other codes (besides DTC P0101) being output?
YES Go to relevant DTC chart.
NO
Replace mass air flow meter.
DI5P0−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00484
Intake Air Temp. Sensor
(Inside the mass air flow meter)
3
4 L−Y
BR−B 5V
ECM
E5
E5
THA
E1
E2
P22420
3
9 R
−
DIAGNOSTICS ENGINE
DI−27
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
If DTCs P0110 (Intake Air Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction),
P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction)\
are output simultaneously, E2 (Sen-
sor Ground) may be open.
1 Connect the OBD II scan tool or TOYOTA hand −held tester, and read value of
intake air temperature.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand−held tester to DLC3.
(c) Turn ignition switch ON and OBD II scan tool or TOYOTA hand−held tester main switch ON.
CHECK:
Read temp. value on the OBD II scan tool or TOYOTA hand −held tester.
OK:
Same as actual intake air temp.
HINT:
If there is open circuit, push OBD II scan tool or TOYOTA hand− held tester indicates − 40° C (− 40°F).
If there is short circuit, OBD II scan tool or TOYOTA handheld tester indicates 140° C (284°F) or more.
NG − 40° C (− 40 °F) ....Go to step 2.
140 °C (284°F) or more ....Go to step 4.
OK
Check for intermittent problems
(See page DI−3 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00156
ON
Engine Coolant
Temp. Sensor ECM
5V
4
9
2
1
E2
E1
THW
E5
E5
BE6653
FI7055
−
DIAGNOSTICS ENGINE
DI−31
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
HINT:
If DTC is P0110 (Intake Air Temp. Circuit Malfunction), P0115 (Engine Coolant Temp. Circuit Malfunction),
P0120 (Throttle/Pedal Position Sensor/Switch ”A” Circuit Malfunction)\
are output simultaneously, E2 (Sen-
sor Ground) may be open.
1 Connect the OBD II scan tool or TOYOTA hand −held tester, and read value of
engine coolant temperature.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and push the OBD II scan tool or TOYOTA hand−held tester main switch ON.
CHECK:
Read temperature value on the OBD II scan tool or TOYOTA hand −held tester.
OK:
Same as actual engine coolant temperature.
HINT:
If there is open circuit, OBD II scan tool or TOYOTA hand−held tester indicates − 40°C (− 40 °F).
If there is short circuit, OBD II scan tool or T OYOTA hand−held tester indicates 140 °C (284 °F) or more.
NG −40°C ( −40° F) ... Go to step 2.
140 °C (284° F) or more ... Go to step 4.
OK
Check for intermittent problems
(See page DI−3 ).
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect the engine coolant temp. sensor connector.
(b) Connect sensor wire harness terminals together.
(c) Turn ignition switch ON.
CHECK:
Read temp. value on the OBD II scan tool or TOYOTA hand −
held tester.
OK:
Temp. value: 140° C (284°F) or more
OK Confirm good connection at sensor. If OK, replace engine coolant temp. sensor.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI6571
Throttle Position
SensorVCCVTA
IDLE2 ECM
5V
B+
−
DIAGNOSTICS ENGINE
DI−35
1996 LAND CRUISER (RM451U)
DTC P0120 Throttle/Pedal Position Sensor/Switch ”A”
Circuit Malfunction
CIRCUIT DESCRIPTION
The throttle position sensor is mounted in the throttle body and
detects the throttle valve opening angle.
When the throttle valve is fully closed, the IDL contacts in the
throttle position sensor are on, so the voltage at the terminal IDL
of the ECM becomes 0 V. At this time, a voltage of approximate-
ly 0.3 − 0.8 V is applied to terminal VTA of the ECM. When the
throttle valve is opened, the IDL contacts go off and thus the
power source voltage of approximately 12 V in the ECM is ap-
plied to the terminal IDL of the ECM. The voltage applied to the
terminal VTA of the ECM increases in proportion to the opening
angle of the throttle valve and becomes approximately 3.2 − 4.9
V when the throttle valve is fully opened. The ECM judges the
vehicle driving conditions from these signals input from termi-
nals VTA and IDL, and uses them as one of the conditions for
deciding the air− fuel ratio correction, power increase correction
and fuel −cut control etc.
DTC No.DTC Detecting ConditionTrouble Area
P0120
Condition (a) or (b) continues
(a) VTA < 0.1 V, and closed throttle position switch is OFF
(b) VTA > 4.9 VOpen or short in throttle position sensor circuit
 Throttle position sensor
 ECM
HINT:
If there is open circuit in IDL line, DTC P0120 does not indicate.
After confirming DTC P0120 use the OBD II scan tool or TOYOTA hand−held tester to confirm the
throttle valve opening percentage and closed throttle position switch condition\
.
Throttle valve opening position
expressed as percentage
Trouble Area
Throttle valve fully closedThrottle valve fully open
0 %0 %VCC line open
VTA line open or short
Approx. 99 %Approx. 100 %E2 line open
DI5P7−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010