1996 TOYOTA LAND CRUISER Starter

S06273
E1
1
G−
2
BR
L
L G1
NE2
NE2−
12
E6
3
2
Distributor
Crankshaft Position Sensor G2
ECM
NE
4
1 L
L
G W
R
E6
E6
E6
E6
E6 11
10 4
56
DI−62
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC P0335 Crankshaft Position Sensor ”A” Circuit Malfunction
CIRCUIT DESCRIPTION
The crankshaft position sensor (NE signal) consists of a signal plate and pick up coil. The NE\
signal plate
has 24 teeth and is built into the distributor. When the camshaft rotates, the protrusion on the signal plate
and the air gap on the pick up coil change, causing fluctuations in the magnetic field and generating an elec-
tromotive force in the pick up coil. The NE signal sensor generates 24 signals fo\
r every engine revolution.
The ECM detects the standard crankshaft angle based on the G1, G2 signals, \
detects the actual crankshaft
angle and the engine speed by the NE signals, and detects misfire by NE2 sign\
als.
DTC No.DTC Detecting ConditionTrouble Area
P0335
No crankshaft position sensor signal (NE signal) to ECM dur-
ing cranking.
(2 trip detection logic) Open or short in crankshaft position sensor circuit for NE
signal.
 Crankshaft position sensor for NE signal
 Starter
 ECM
No crankshaft position sensor signal (NE signal) to ECM with
engine speed 550 rpm or more (2 trip detection logic)
WIRING DIAGRAM
DI5PH−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−102
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC P1335 Crankshaft Position Sensor Circuit Malfunction (during engine running)
CIRCUIT DESCRIPTION
Refer to DTC P0335 (Crankshaft Position Sensor ”A” Circuit Malfunction\
) on page DI−62.
DTC No.DTC Detecting ConditionTrouble Area
P1335No crankshaft position sensor signal (NE signal) to ECM with
engine speed 1,000 rpm or more
Open or short in crankshaft position sensor circuit for NE
signal
 Crankshaft position sensor for NE signal
 Starter
 ECM
WIRING DIAGRAM
See DTC P0335 (Crankshaft Position Sensor ”A” Circuit Malfunction) \
for WIRING DIAGRAM and INSPEC-
TION PROCEDURE.
DI5PR−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A15825
−
DIAGNOSTICS ENGINE
DI−103
1996 LAND CRUISER (RM451U)
DTC P1500 Starter Signal Circuit Malfunction
CIRCUIT DESCRIPTION
When the engine is cranked, the intake air flow is slow, so fuel vaporization is poor. A rich mixture is therefore
necessary in order to achieve good startability. While the engine is being cranked, the battery positive volt-
age is applied to terminal STA of the ECM. The starter signal is mainly used to increase the fuel inj\
ection
volume for the starting injection control and after −start injection control.
WIRING DIAGRAM
DI968−01
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−104
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
HINT:
This diagnostic chart is based on the premise that the engine is cranked normally. If the engine is not
cranked, proceed to the matrix chart of problem symptoms on page DI−19.
1 Connect TOYOTA hand −held tester and check STA signal.
PREPARATION:
(a) Connect the TOYOTA hand−held tester to the DLC3.
(b) Turn ignition switch ON and push TOYOTA hand −held tester main switch ON.
CHECK:
Read STA signal on the TOYOTA hand −held tester while starter operates.
OK:
Ignition Switch PositionONSTART
STA SignalOFFON
OK Proceed to next circuit inspection shown on matrix chart (See page DI−19 ).
NG
2 Check for open in harness and connector between ECM and starter relay (See page IN−28 ).
NG Repair or replace harness or connector.
OK
Check and replace ECM
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22478
Battery
FL AM1
Fusible Link
1F6
B−L
2
2 2
2
3
4
AM1
R/B No.2
Junction
Connector (J4)
Y Y
IG Switch
4 2
1 B−W
B−YFuse Block
GAUGE
Y
B
B 6IH14
B−W Park/Neutral
Position Switch
3
2 G−R G−W
O
O
IH2
To A/T Indicator Light
(Combination Meter)
Starter
1
S1 E7
E7
E7
17
16
22 NSW
E1B+
E1 E1
L
2 ECM
W
EA26
B
B
B−R
65 3
2IH1
21
B−W
IH2
DI−108
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC P1780 Park/Neutral Position Switch Malfunction
CIRCUIT DESCRIPTION
The park/neutral position switch goes on when the shift lever is in the N o\
r P shift position. When it goes on
terminal NSW of the ECM is grounded to body ground via the starter relay, thus the terminal NSW voltage
becomes 0 V. When the shift lever is in the D, 2, L or R position, the park/neutral\
position switch goes off,
so the voltage of ECM, terminal NSW becomes battery voltage, the voltage of the ECM internal power
source. If the shift lever is moved from the N position to the D position, this signal is used for air\
−fuel ratio
correction and for idle speed control (estimated control), etc.
DTC No.DTC Detecting ConditionTrouble Area
P1780
2 or more switches are ON simultaneously for ”N”, ”2” and ”\
L”
position (2 trip detection logic)
 Short in park/neutral position switch circuit
 Park/neutral position switch
 ECMWhen driving under conditions (a) and (b) for 30 sec. or more
the park/neutral position switch is ON (N position):
(2 trip detection logic)
(a) Vehicle speed: 70 km/h (44 mph) or more
(b) Engine speed: 1,500 − 2,500 rpm
HINT:
After confirming DTC P1780 use the T OYOTA hand−held tester to confirm the PNP switch signal from ”CUR-
RENT DATA”.
WIRING DIAGRAM
DI5PV−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22480
BatteryStarter
FL MAIN
FL AM2EFI
EFI Main Relay
IG Switch IG
ST
Park/Neutral
Position SwitchCircuit Opening
Relay
Fuel Pump Relay
Fuel Pump
From Crankshaft Position
Sensor Fuel Pump
Resistor
(STA Signal)
(NE Signal) MRLY
FC
STA
NE
Tr1
Tr2
ECM
IGN FPR
−
DIAGNOSTICS ENGINE
DI−11 5
1996 LAND CRUISER (RM451U)
Fuel Pump Control Circuit
CIRCUIT DESCRIPTION
In the diagram below, when the engine is cranked, current flows form terminal ST of the igni\
tion switch to
terminal STA of ECM (STA signal).
When the STA signal and NE signal are input to the ECM, Tr1 is turned ON, current flows to coil of the circuit
opening relay, the relay switches on, power is supplied to the fuel pump and the fuel\
pump operates.
While the NE signal is generated (engine running), the ECM keeps Tr1 ON (circuit opening relay ON) and
the fuel pump also keeps operating.
The fuel pump speed is controlled at 2 levels (high speed or low speed) b\
y the condition of the engine (start-
ing, light load, heavy load). When the engine starts (STA ON), Tr2 in the ECM is OFF, so battery voltage is
applied directry to the fuel pump. Fuel pump operates at high speed.
After the engine starts, during idling or light loads, since Tr2 goes ON, power is supplied to the fuel pump
via the fuel pump resistor.
Fuel pump operates at low speed.
DI5PY−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08577D00180
ECM
Combination Meter
Battery
Park/Neutral
Position Switch
Fuse Block
Starter
From
Battery L
2
R
NSW
E717
16 15
C12
G−W
E7E7
E7
L
R
2
C12
C12
R−B R−B
G−W
O
O
IH2
B−W 22
43
1
2B−W
IG1
ST1 2 4
AM1
2
2
2 2
1
2
AM1
3
J4
EA2 1 8
GAUGE
W
B F6
FLAM1
B+
IH2
IH1 IH1
B−L
B
6
Ignition Switch
4 R/B No. 2
6
6
B
B
Y
Y
15
B−R
B−WO
G−R R−B
S1
S2
10 4
11
2
3
21 7
Y
B−Y 1
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−169
1996 LAND CRUISER (RM451U)
DTC P1780 Park/Neutral Position Switch Malfunction
CIRCUIT DESCRIPTION
The park/neutral position switch detects the shift lever position and sends\
signals to the ECM.
The ECM receives signals (NSW, R, 2 and L) from the park/neutral position switch. When the signal is\
not
sent to the ECM from the park/neutral position switch, the ECM judges th\
at the shift lever is in D position.
DTC No.DTC Detection ConditionTrouble Area
P1780
2 or more switches are ON simultaneously for N, 2 and L posi-
tions (2 trip detection logic)
Short in park/neutral position switch circuit
 Park/neutral position switch
 ECMWhen driving under conditions (a), (b) and (c) for 30 sec. or
more, the park/neutral position switch is ON (N position)
(2 trip detection logic)
(a) Vehicle speed: 70 km/h (44 mph) or more
(b) Engine speed: 1,500 − 2,500 rpm
(c) Engine load: 0.6 g/rev. or more
WIRING DIAGRAM
DI5KY−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Input SignalIndicator Light
Blinking Pattern
Turn PNP switch
OFF (Shift to
except D position)
LightON
OFF SW ON
SW OFF
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−323
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check starter operation.
CHECK:
Check that the starter operates normally and that the engine starts.
NG Proceed to engine troubleshooting (See page DI−1).
OK
2 Input signal check.
PREPARATION:
See input signal check on page DI−286.
CHECK:
Check the indicator light when shifting into except D position.
OK:
The indicator light goes off when shifting into except
D position.
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−295 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010