1996 TOYOTA LAND CRUISER batte

AB0117 AB0118 AB0119
R12658H00032
LOCKACCON
or
Airbag Sensor Assembly
Tc
DI−282
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
4 Check airbag sensor assembly.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative ( −) terminal cable from the battery,
and wait at least 90 seconds.
(c) Disconnect airbag sensor assembly connector.
(d) Insert service wire into terminal Tc from back side as shown.
(e) Connect airbag sensor assembly connector with service wire.
(f) Connect negative (−) terminal cable to battery.
(g) Turn ignition switch to ACC or ON, and wait at least 20 se-
conds.
(h) Connect service wire of terminal Tc to body ground.
CHECK:
Check operation of SRS warning light.
OK:
SRS waning light comes on.
NOTICE:
Never make a mistake with the terminal connection posi-
tion as this will cause a malfunction.
OK Check harness between airbag sensor assem- bly and DLC1.
NG
Replace airbag sensor assembly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AB0117
R14303H00033
LOCK
Airbag Sensor Assembly
Tc
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−283
1996 LAND CRUISER (RM451U)
If the DTC is displayed without a DTC check procedure, perform the followi\
ng
troubleshooting.
1 Check resistance between terminal Tc of airbag sensor assembly and body
ground.
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative ( −) terminal cable from the battery,
and wait at least 90 seconds.
(c) Disconnect airbag sensor assembly connector.
CHECK:
Check resistance between terminal Tc of airbag sensor assem-
bly connector and body ground.
OK:
Resistance: 1 MΩ or Higher
NG Repair or replace harness or connector.
OK
Replace airbag sensor assembly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00489
Cruise Control ECUL
L−
W−B
1
5
4 3
2 R
1026
C4 Stop Light Switch
4
R−G
Cruise
Control Actuator
C17
C17
C17
C4S13
S13 S13
S13
G−O G−WF11F11
1
2
STOP
Instrument Panel Fuse Block
W
EA3
W
3
1
F8
Battery Fusible Link
FL MAIN
STP−
DI−298
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
DTC 12 Actuator Magnetic Clutch Circuit
CIRCUIT DESCRIPTION
This circuit turns on the magnetic clutch inside the actuator during cruise \
control operation according to the
signal from the ECU. If a malfunction occurs in the actuator or speed sensor, etc. during cruise control opera-
tion, the rotor shaft between the motor and control plate is released.
When the brake pedal is depressed, the stop light switch turns on, supplying electrical power to the stop light.
Power supply to the magnetic clutch is mechanically cut and the magnetic clut\
ch is turned OFF.
When driving downhill, if the vehicle speed exceeds the set speed by 15 km/h\
(9 mph), the ECU turns the
safety magnet clutch OFF. If the vehicle speed later drops to within 10 km/h (6 mph) above the\
set speed,
then cruise control at the set speed is resumed.
DTC No.Detection ItemTrouble Area
12 Short in actuator magnetic clutch circuit.
 Open (0.8 sec.) in actuator magnetic clutch circuit.
STOP Fuse
 Stop light switch
 Actuator magnetic clutch
 Harness or connector between cruise control ECU and
actuator magnetic clutch, actuator magnetic clutch and body
ground
 Cruise control ECU
WIRING DIAGRAM
DI5OC−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00054
54
(+)
(−)
DI−304
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
DTC 14 Actuator Mechanical Malfunction
CIRCUIT DESCRIPTION
The circuit detects the rotation position of the actuator control plate and\
sends a signal to the ECU.
DTC No.Detection ItemTrouble Area
14
 Open in actuator motor circuit.
 Position sensor signal valve does not change when the
motor operates.
Actuator lock: (motor, arm)
 Actuator motor
 Harness or connector between cruise control ECU and
actuator motor
 Cruise control ECU
WIRING DIAGRAM
See page DI−296 .
INSPECTION PROCEDURE
1 Check cruise control actuator arm locking operation
PREPARATION:
(a) Turn ignition switch OFF.
(b) Disconnect the actuator connector.
CHECK:
(a) Connect the positive (+) lead from the battery to the termi-
nal 5 of actuator and the negative ( −) lead to terminal 4.
NOTICE:
Do not connect the high tension cables to the wrong bat-
tery terminal. You will damage the cruise control actuator.
(b) Move the control plate by hand.
OK:
Control plate does not move.
NG Replace cruise control actuator.
OK
DI5OE−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00131
I00132I00008
I00010
I00132
Fully open side
Control plate Fully close side
Control Plate 4
5
674
6
5
7
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−305
1996 LAND CRUISER (RM451U)
2 Check cruise control actuator operation.
PREPARATION:
(a) Turn ignition switch OFF.
(b) Disconnect the actuator connector.
CHECK:
Connect the positive (+) lead from the battery to terminals 5 and
6 of actuator, connect the negative (−) lead to terminals 4 and
7 of actuator.
OK:
Control arm moves to full open side
CHECK:
Connect the positive (+) lead from the battery to terminals 4 and
7of actuator, connect the negative ( −) lead to terminals 5 and
6 of actuator.
OK:
Control arm moves to full colse side
NG Replace cruise control actuator.
OK
3 Check harness and connector between cruise control ECU and cruise contro\
l ac- tuator (See page IN−28 ).
NG Repair or replace harness or connector.
OK
Check and replace cruise control ECU (See
page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00491
Cruise Control ECU
C17
Speedometer
(Combination Meter)
C13
C13
4 3
Vehicle Speed Sensor (Combination Meter) R−O
R−O
R−G
R−G 25
1
Ea1EC1
IH1L−W
BR Air Intake Chamber
EC
V1
V1
V13 2
1
1
Ea1 EC1
3 6
Y
Y GAUGE
AM1
Y
Y
BR
BR
EC1
Ea1 IH1
22
Instrument Panel Fuse
Block
Fusible Link BatteryWB
B
I12
I12
Ignition Switch 2
4
1
3
F11
F11Y
B
B
J4
JUNCTION
CONNECTOR
EA1
6
2
2 3
4
B−L
FL MAIN
F6
1 B−Y
39
20
SPD
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−307
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Input SignalIndicator Light
Blinking Pattern
Stop Light
switch ON
Light ON
OFF SW OFF
SW ON
DI−314
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Stop Light Switch Circuit
CIRCUIT DESCRIPTION
When the brake pedal is depressed, the stop light switch sends a signal to th\
e ECU. When the ECU receives
this signal, it cancels the cruise control.
A fail− safe function is provided so that the cancel functions normally , even if there is a malfunction in the stop
light signal circuit.
The cancel conditions are: Battery positive voltage at terminal STP −
When the brake is on, battery positive voltage normally applies through the S\
TOP fuse and stop light switch
to terminal STP− of the ECU, and the ECU turns the cruise control off.
If the harness connected to terminal STP − has an open circuit, terminal STP − will have battery positive volt-
age and the cruise control will be turned off.
Also, when the brake is on, the magnetic clutch circuit is cut mechanically \
by the stop light switch, turning
the cruise control off (See page DI−298 for operation of the magnetic clutch).
WIRING DIAGRAM
See page DI−298 .
INSPECTION PROCEDURE
1 Check operation of stop light.
CHECK:
Check that stop light comes on when brake pedal is depressed, and turns off when brake pedal is released.
NG Check stop light system (See page BE−24 ).
OK
2 Input signal check.
CHECK:
(a) See input signal check on DI−286.
(b) Check the indicator light when the brake pedal is de-
pressed.
OK:
The indicator light goes off when the brake pedal is
depressed.
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−295 ).
NG
DI5OI−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I00495
Cruise Control ECUD
2
Y Y
B
B 4
Instrument Panel Fuse Block B−O
IH1
1 3
6
B−O
GAUGE
9
2 4
Ignition Switch C17
B−Y FL AM1 AM1
EA2 2
1
B
B 6
Battery 2
1 W
2 2
B−L
A/T Indicator Light
(Park/Neutral Position Switch)
IH24
P1
P1
F11 F11 J4
JUNCTION
CONNECTOR
I12 I12 Fusible Link
F6 2
D
Fusible Link
Y
DI−322
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Park/Neutral Position Switch Circuit
CIRCUIT DESCRIPTION
When the shift position is put in except D position, a signal is sent from t\
he park/neutral position switch to
the ECU. When this signal is input during cruise control driving, the EC\
U cancels the cruise control.
WIRING DIAGRAM
DI5OL−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010