1996 TOYOTA LAND CRUISER Oil engine

LU0KE−03
LU−2
−
LUBRICATION OIL AND FILTER
1996 LAND CRUISER (RM451U)
REPLACEMENT
CAUTION:
Prolonged and repeated contact with mineral oil will result
in the removal of natural fats from the skin, leading to dry-
ness, irritation and dermatitis. In addition, used engine oil
contains potentially harmful contaminants which may
cause skin cancer.Care should be taken, therefore, when
changing engine oil to minimize the frequency and length
of time your skin is exposed to used engine oil. Protective
clothing and gloves that cannot be penetrated by oil should
be worn. The skin should be thoroughly washed with soap
and water, or use water−less hand cleaner, to remove any
used engine oil. Do not used gasoline, thinners, or sol-
vents.In order to preserve the environment, used oil and
used oil filters must be disposed of only at designated dis-
posal sites.
1. DRAIN ENGINE OIL
(a) Remove the oil filler cap.
(b) Remove the oil drain plug, and drain the oil into a contain-
er.
2. REPLACE OIL FILTER
(a) Using SST, remove the oil filter. SST 09228−44011
(b) Check and clean the oil filter installation surface.
(c) Apply clean engine oil to the gasket of a new oil filter.
(d) Lightly screw the oil filter into place, and tighten it until the
gasket contacts the seat.
(e) Using SST, tighten it an additional 3/4 turn. SST 09228−44011
3. FILL WITH ENGINE OIL
(a) Clean and install the oil drain plug with a new gasket.
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(b) Fill with new engine oil. Oil grade:
See step 1 in oil pressure check
Capacity:
Drain and refill
w/ Oil filter change
7.2 liters (7.5 US qts, 6.3 lmp. qts)
w/o Oil filter change
6.9 liters (7.3 US qts, 6.1 lmp. qts)
Dry fill
8.0 liters (8.5 US qts, 7.0 lmp. qts)
(c) Reinstall the oil filler cap.
4. START ENGINE AND CHECK FOR LEAKS
5. RECHECK ENGINE OIL LEVEL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU0KG−02
−
LUBRICATION OIL PUMP
LU−5
1996 LAND CRUISER (RM451U)
REMOVAL
HINT:
When repairing the oil pump, the oil pan and strainer should be
removed and cleaned.
1. DRAIN ENGINE OIL
2. REMOVE ENGINE UNDER COVER
3. DRAIN ENGINE COOLANT
4. REMOVE RADIATOR (See page CO−14 )
5. DISCONNECT A/C COMPRESSOR AND BRACKET
(a) Loosen the idler pulley nut and adjusting bolt, and remove
the drive belt.
(b) Remove the 4 mounting bolts, and disconnect the com- pressor from the bracket.
HINT:
Put aside the compressor, and suspend it.
(c) Remove the 5 bolts and A/C compressor bracket.
6. REMOVE RADIATOR PIPE
(a) Disconnect the No.2 radiator hose from the water inlet.
(b) Remove the 2 nuts and radiator pipe.
7. REMOVE WATER PUMP
Remove the 4 bolts, 2 nuts, water pump and gasket.
8. REMOVE CYLINDER HEAD (See page EM−28 )
9. DISCONNECT OIL COOLER PIPE BRACKET FROM NO.1 OIL PAN
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU0KH−01
−
LUBRICATION OIL PUMP
LU−9
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT RELIEF VALVE
Coat the valve with engine oil and check that it falls smoothly
into the valve hole by its own weight.
If it does not, replace the relief valve. If necessary, replace the
oil pump assembly.
2. INSPECT ROTOR BODY CLEARANCE
Using a thickness gauge, measure the clearance between the
driven rotor and body.
Standard body clearance:
0.100 − 0.170 mm (0.0039 − 0.0067 in.)
Maximum body clearance:
0.30 mm (0.0118 in.)
If the body clearance is greater than maximum, replace the ro-
tors as a set. If necessary, replace the oil pump assembly.
3. INSPECT ROTOR SIDE CLEARANCE
Using a thickness gauge and precision straight edge, measure
the clearance between the rotors and precision straight edge. Standard side clearance:
0.030 − 0.090 mm (0.0012 − 0.0035 in.)
Maximum side clearance:
0.15 mm (0.0059 in.)
If the side clearance is greater than maximum, replace the ro-
tors as a set. If necessary, replace the oil pump assembly.
4. INSPECT ROTOR TIP CLEARANCE
Using a thickness gauge, measure the clearance between the
drive and driven rotor tips. Standard tip clearance:
0.030 − 0.160 mm (0.0012 − 0.0063 in.)
Maximum tip clearance:
0.25 mm (0.0098 in.)
If the tip clearance is greater than maximum, replace the rotors
as a set.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
LUBRICATION OIL PUMP
LU−13
1996 LAND CRUISER (RM451U)
(c) Install a new gasket in position.
(d) Pour in approximately 15 cm
3 (0.9 cu in.) of engine oil into
oil pump hole.
(e) Install the No.1 oil pan with the 21 bolts and 2 nuts. Torque:
14 mm head: 44 N·m (440 kgf·cm, 32 ft·lbf)
12 mm head: 20 N·m (200 kgf·cm, 14 ft·lbf)
9. INSTALL NO.2 OIL PAN
(a) Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surface of the No.1 oil
pan.
Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing grooves.
Thoroughly clean all components to remove all the
loose material.
Using a non −residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the No.2 oil pan as shown in the il- lustration.
NOTICE:
Do not use a solvent which will affect the painted surfaces. Seal packing: Part No. 08826−00080 or equivalent
Install a nozzle that has been cut to a 2 − 3 mm (0.08
− 0.12 in.) opening or 3 − 4 mm (0.012 − 0.016 in.)
opening.
HINT:
Avoid applying an excessive amount to the surface.
Parts must be assembled within 5 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.
Immediately remove nozzle from the tube and rein-
stall cap.
(c) Install the No.2 oil pan with the 17 bolts and 2 nuts. Torque: 7.8 N·m (80 kgf·cm, 69 in.·lbf)
Torque: 8.8 N·m (90 kgf·cm, 78 in.·lbf)
10. INSTALL BOL TS HOLDING NO.1 OIL PAN TO TRANS-
MISSION HOUSING
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU−14
−
LUBRICATION OIL PUMP
1996 LAND CRUISER (RM451U)
Install the 6 bolts.
Torque: 72 N·m (730 kgf·cm, 53 ft·lbf)
11. INSTALL OIL LEVEL SENSOR
(a) Install a new gasket to the level sensor.
(b) Install the level sensor with the 4 bolts. Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
12. CONNECT OIL COOLER PIPE BRACKET TO NO.1 OIL
PA N
13. INSTALL CYLINDER HEAD(See page EM−54)
14. INSTALL WATER PUMP
Install a new gasket and water pump with the 4 bolts and 2 nuts. Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
15. INSTALL RADIATOR PIPE
(a) Connect the No.2 radiator hose to the water inlet.
(b) Install the 2 nuts holding the radiator pipe to the No.1 oil pan.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
16. INSTALL A/C COMPRESSOR AND BRACKET
(a) Install the A/C compressor bracket with the 5 bolts. Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(b) Install the A/C compressor with the 4 bolts.
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(c) Install and adjust the drive belt (See page CH−2).
17. INSTALL RADIATOR (See page CO−16 )
18. INSTALL ENGINE UNDER COVER
19. FILL WITH ENGINE OIL
20. START ENGINE AND CHECK FOR LEAKS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU0KK−02
LU−16
−
LUBRICATION OIL COOLER
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. REMOVE AIR CLEANER CAP AND HOSE
3. REMOVE FRONT EXHAUST PIPE
(a) Disconnect the heated oxygen sensor connector.
(b) Remove the 2 nuts and 2 bolts holding the front exhaust pipe to the rear TWC.
(c) Disconnect the front exhaust pipe, and remove the gas- ket.
(d) Loosen the clamp bolt and disconnect the clamp from the
No.1 support bracket.
(e) Remove the 2 bolts and No.1 support bracket.
(f) Remove the 4 nuts, front exhaust pipe and 2 gaskets.
4. REMOVE NO.1 EXHAUST MANIFOLD
(a) Remove the 3 bolts and No.1 heat insulator.
(b) Remove the 6 nuts, exhaust manifold and gasket.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU08Y−03
LU−18
−
LUBRICATION OIL COOLER
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT RELIEF VALVE
Coat the valve with engine oil and check that it falls smoothly
into the valve hole by its own weight.
If it doesn’t, replace the relief valve. If necessary, replace the oil
cooler cover.
2. INSPECT OIL COOLER
Check the oil cooler for damage or clogging.
If necessary, replace the oil cooler.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU08Z−04
P08343
Adhesive
−
LUBRICATION OIL COOLER
LU−19
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL RELIEF VALVE
Install the relief valve, spring and a new gasket with the plug.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
2. ASSEMBLE OIL COOLER AND OIL COOLER COVER
Install 2 new gaskets and the oil cooler to the oil cooler cover
with the 4 nuts. Torque: 17 N·m (170 kgf·cm, 12 ft·lbf)
3. INSTALL OIL COOLER AND OIL COOLER COVER ASSEMBLY
Install a new gasket, the oil cooler and oil cooler cover assembly
with the 10 bolts and 2 nuts. Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
4. INSTALL OIL PRESSURE SWITCH
(a) Apply adhesive to 2 or 3 threads of the oil pressure switch.
Adhesive:
Part No. 08833 −00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(b) Install the oil pressure switch.
5. INSTALL NO.1 EXHAUST MANIFOLD
(a) Install a new gasket and the exhaust manifold with the 6 nuts.
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
(b) Install the heat insulator with the 3 bolts. Torque: 19 N·m (195 kgf·cm, 14 ft·lbf)
6. INSTALL FRONT EXHAUST PIPE
(a) Install 2 new gaskets and the front exhaust pipe with the 4 nuts.
Torque: 63 N·m (630 kgf·cm, 46 ft·lbf)
(b) Install the No.1 support bracket with the 2 bolts. Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
(c) Connect the clamp and tighten the clamp bolt. Torque: 19.5 N·m (195 kgf·cm, 14 ft·lbf)
(d) Connect the front exhaust pipe to the rear TWC with a new gasket, 2 bolts and 2 nuts.
Torque: 46 N·m (470 kgf·cm, 34 ft·lbf)
7. INSTALL AIR CLEANER CAP AND HOSE
8. FILL RADIATOR WITH ENGINE COOLANT
9. START ENGINE AND CHECK FOR LEAKS
10. CHECK ENGINE OIL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010