1996 TOYOTA LAND CRUISER Instrument

−
SFI INJECTOR
SF−31
1996 LAND CRUISER (RM451U)
(d) Remove SST.
SST 09268−41045
(e) Reinstall the fuel pressure regulator to the delivery pipe
(See page SF−22 ).
(f) Disconnect the TOYOTA hand− held tester from the
DLC3.
(g) Reinstall the fuse cover on the instrument panel.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF0Q2−08
−
SFI FUEL CUT RPM
SF−67
695
Author: Date:
1996 LAND CRUISER (RM451U)
FUEL CUT RPM
INSPECTION
1. WARM UP ENGINE
Allow the engine to warm up to normal operating temperature.
2. CONNECT TOYOTA HAND −HELD TESTER OR OBD II
SCAN TOOL
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester or OBD II scan tool to the DLC3.
(c) Please refer to the TOYOTA hand−held tester or OBD II
scan tool operator’s manual for further details.
3. INSPECT FUEL CUTOFF PRM
(a) Increase the engine speed to at least 3,500 rpm.
(b) Use a sound scope to check for injector operating noise.
(c) Check that when the throttle lever is released, injector op-
eration noise stops momentarily and then resumes.
HINT:
Measure with the A/C OFF. Fuel return rpm: 1,200 rpm
4. DISCONNECT TOYOTA HAND −HELD TESTER OR
OBD II SCAN TOOL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR−12
−
STEERING TILT STEERING COLUMN
1996 LAND CRUISER (RM451U)
3. REMOVE INSTRUMENT LOWER FINISH PANEL
(a) Disconnect the hood lock control cable and fuel lid control
cable.
(b) Remove the 4 panel set screws.
4. REMOVE NO.2 HEATER TO REGISTER DUCT
5. REMOVE UPPER AND LOWER COLUMN COVERS
Remove the 5 screws.
6. REMOVE COMBINATION SWITCH WITH SPIRAL CABLE
(a) Disconnect the 2 connectors.
(b) Disconnect the airbag connector.
(c) Remove the 4 screws.
NOTICE:
Do not disassemble the cable or apply oil to it.
7. REMOVE 4 COLUMN HOLE COVER SET BOLTS
8. REMOVE LINK JOINT PROTECTOR
Remove the 2 bolts.
9. DISCONNECT SLIDING YOKE SUB−ASSEMBLY
(a) Place matchmarks on the yoke sub −assembly and worm
gear valve body shaft.
(b) Loosen bolt A and remove bolt B.
10. REMOVE SLIDING YOKE SUB−ASSEMBLY
Remove the bolt A.
11. REMOVE TILT STEERING COLUMN ASSEMBLY
(a) Disconnect the 3 connectors.
(b) Remove the 2 column assembly set nuts and 2 set bolts.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SR16E−03
−
STEERING TILT STEERING COLUMN
SR−19
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL STEERING COLUMN ASSEMBLY
(a) Torque the 2 column assembly set nuts and 2 set bolts.
Torque:25 N·m (250 kgf·cm, 18 ft·lbf)
(b) Connect the 3 connectors.
2. INSTALL SLIDING YOKE SUB −ASSEMBLY
Temporarily tighten the bolt A.
3. CONNECT SLIDING YOKE SUB−ASSEMBLY
(a) Align the matchmarks on the yoke sub−assembly and
worm gear valve body shaft.
(b) Torque the bolt B. Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
(c) Torque the bolt A.
Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
4. INSTALL LINK JOINT PROTECTOR
Torque the 2 bolts. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
5. TORQUE 4 COLUMN HOLE COVER SET BOLTS Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
6. INSTALL COMBINATION SWITCH WITH SPIRAL CABLE
(a) Tighten the 4 screws.
(b) Connect the airbag connector.
(c) Connect the 2 connectors.
7. INSTALL UPPER AND LOWER COLUMN COVERS
Tighten the 5 screws.
8. INSTALL NO.2 HEATER TO REGISTER DUCT
9. INSTALL INSTRUMENT LOWER FINISH PANEL
(a) Tighten the 4 panel set screws.
(b) Connect the hood lock control cable and fuel lid control cable.
10. CENTER SPIRAL CABLE
(a) Check that the front wheels are facing straight ahead.
(b) Turn the cable counterclockwise by hand until it becomes harder to turn the cable.
(c) Then rotate the cable clockwise about 3 turns to align the
red mark.
HINT:
The cable will rotate about 3 turns to either left or right of the
center.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EI−01
−
SERVICE SPECIFICATIONS SUPPLEMENTAL RESTRAINT SYSTEM
SS−39
162
Author: Date:
1996 LAND CRUISER (RM451U)
SUPPLEMENTAL RESTRAINT SYSTEM
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Steering wheel set nut3435025
Steering wheel pad9.09080 in.·lbf
Front passenger airbag assembly x Instrument panel reinforcement2020515
Airbag sensor assembly2020515
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EK−02
−
SERVICE SPECIFICATIONS BODY
SS−41
164
Author: Date:
1996 LAND CRUISER (RM451U)
BODY
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
FRONT BUMPER
Front bumper arm x Front bumper bracket3940029
Front bumper arm x Body3940029
Front bumper extension x Front bumper5.45548 in.·lbf
REAR BUMPER
Rear bumper extension x Rear bumper reinforcement131309
Rear bumper extension reinforcement x Body5.45548 in.·lbf
HOOD
Hood hinge x Body1818513
Hood lock x Body88069 in.·lbf
FRONT DOOR
Door hinge x Body2424017
Door hinge x Door panel2424017
Door lock x Door panel55043 in.·lbf
Window regulator x Door panel55043 in.·lbf
REAR DOOR
Door hinge x Body2424017
Door hinge x Door panel2424017
Door lock x Door panel55043 in.·lbf
Window regulator x Door panel55043 in.·lbf
WIPER AND WASHER
Front wiper arm x Wiper link2021015
Wiper link x Body5.45548 in.·lbf
Wiper motor x Body5.45548 in.·lbf
Rear wiper arm x Wiper motor5.45548 in.·lbf
WHEEL OPENING EXTENSION
Front wheel opening extension x Body5.45548 in.·lbf
Rear wheel opening extension x Body5.45548 in.·lbf
INSTRUMENT P ANEL
Front passenger airbag assembly x Instrument panel reinforcement2021015
FRONT MANUAL SEAT
Seat truck x Body3940029
Seat reclining assembly x Seatback frame5253038
Lumber support x Seatback frame1818513
FRONT POWER SEAT
Seat truck x Body3940029
Power seat adjuster x Seatback frame3737527
Power seat adjuster x Seatback cushion frame1818513
Lumber support x Seatback frame1818513
NO. 1 REAR SEAT
Seat cushion hinge x Body3940029
Seat cushion hinge x Seat cushion frame3940029
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010