1996 TOYOTA LAND CRUISER engine

DI−14
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC No.
(See Page)
Detection ItemTrouble AreaMILMemory
P0171
( DI−51 )System too Lean
(Fuel T rim)
Air intake (hose loose)
 Fuel line pressure, leak
 Injector blockage
 Heated oxygen sensor malfunction
 Mass air flow meter
 Engine coolant temp. sensor
 *1
P0172
( DI−51 )System too Rich
(Fuel T rim)
Fuel line pressure
 Injector leak, blockage
 Heated oxygen sensor malfunction
 Mass air flow meter
 Engine coolant temp. sensor
 *1
P0300
( DI−54 )Random/Multiple Cylinder
Misfire DetectedIgnition system
 Injector
 Fuel line pressure
 EGR
 Compression pressure
 Valve clearance not to specification
 Valve timing
 Mass air flow meter
 Engine coolant temp. sensor
 *2
P0301
P0302
P0303
P0304
P0305
P0306
( DI−54 )Misfire Detected
− Cylinder 1
− Cylinder 2
− Cylinder 3
− Cylinder 4
− Cylinder 5
− Cylinder 6
P0325
( DI−59 )Knock Sensor 1 Circuit
MalfunctionOpen or short in knock sensor 1 circuit
 Knock sensor 1 (looseness)
 ECM
 *1
P0330
( DI−59 )Knock Sensor 2 Circuit
MalfunctionOpen or short in knock sensor 2 circuit
 Knock sensor 2 (looseness)
 ECM
 *1
P0335
( DI−62 )Crankshaft Position Sensor
”A” Circuit Malfunction
Open or short in crankshaft position sensor circuit for NE sig-
nal
 Crankshaft position sensor for NE signal
 Starter
 ECM
 *1
P0340
( DI−65 )Camshaft Position Sensor
Circuit MalfunctionOpen or short in camshaft position sensor circuit
 Camshaft position sensor
 ECM
 *1
P0385
( DI−67 )Crankshaft Position Sensor
”B” Circuit Malfunction
Open or short in crankshaft position sensor circuit for NE2
signal
 Crankshaft position sensor for NE2 signal
 ECM
 *1
P0401
( DI−69 )Exhaust Gas Recirculation
Flow Insufficient Detected
EGR valve stuck closed
 Short in VSV circuit for EGR
 Open in EGR gas temp. sensor circuit
 EGR hose disconnected
 ECM
 *1
P0402
( DI−80 )Exhaust Gas Recirculation
Flow Excessive Detected
EGR valve stuck open
 EGR VSV open malfunction
 Open in VSV circuit for EGR
 Short in EGR gas temp. sensor circuit
 ECM
 *1
*1: MIL lights up
*2: MIL lights up or blinking
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−15
1996 LAND CRUISER (RM451U)
DTC No.
(See Page)
Detection ItemTrouble Area*MILMemory
P0420
( DI−84 )Catalyst System Efficiency
Below Threshold Three− way catalytic convertor
 Open or short in heated oxygen sensor circuit
 Heated oxygen sensor

P0500
( DI−87 )Vehicle Speed Sensor
Malfunction
Combination meter
 Open or short in speed sensor circuit
 ECM
 Vehicle speed sensor

P0505
( DI−89 )Idle Control System
Malfunction
IAC valve is stuck or closed
 Open or short in IAC valve circuit
 Open or short A/C signal circuit
 Air intake (hose loose)

P0510
( DI−93 )Closed Throttle Position
Switch MalfunctionOpen in closed throttle position switch circuit
 Closed throttle position switch
 ECM

P1300
( DI−97 )Igniter Circuit Malfunction
Open or short in IGF or IGT circuit from igniter to ECM
 Igniter
 ECM

P1335
( DI−102 )Crankshaft Position Sensor
Circuit Malfunction
(during engine running)
Open or short in crankshaft position sensor circuit for NE sig-
nal
 Crankshaft position sensor for NE signal
 Starter
 ECM
−
P1500
( DI−103 )Stater signal circuit MalfunctionOpen or short in starter signal circuit
 ECM−
P1600
( DI−105 )ECM BATT MalfunctionOpen in back up power source circuit
 ECM
P1605
( DI−107 )Knock Control CPU MalfunctionECM
P1780
( DI−108 )Park/Neutral Position Switch
MalfunctionShort in park/neutral position switch circuit
 Park/neutral position switch
 ECM

*: −  MIL does not light up,   MIL lights up
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OW−03
A15824
DI−16
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
PARTS LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OX−03
FI6526
12345678910
11
1213
1415161718192021222324252612345678
910
11
1213141516 123456
78
910
11
12 12345678910
11
1415161718192021221213
E4 E5E6 E7
ECM Terminals
−
DIAGNOSTICS ENGINE
DI−17
1996 LAND CRUISER (RM451U)
TERMINALS OF ECM
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
BATT (E7 − 2) − E1 (E4 − 24)R − Y ↔ BR − BAlways9 − 14
+ B (E7 − 12) − E1 (E4 − 24)Y ↔ BR − BIG switch ON9 − 14
VCC (E5 − 1) − E2 (E5 − 9)R − G ↔ BR − BIG switch ON4.5 − 5.5
IDL (E5 − 11) − E2 (E5 − 9)G − W ↔ BR − B
IG switch ON and apply vacuum to the throttle opener
Throttle valve fully closed0 − 3
IG switch ON
Throttle valve fully open9 − 14
VTA (E5 − 10) − E2 (E5 − 9)G − B↔ BR − B
IG switch ON
Throttle valve fully closed0.3 − 0.8
IG switch ON
Throttle valve fully open3.2 − 4.9
VG (E5 − 2) − E21 (E5 − 16)G − BRIdling, N position, A/C switch OFF1.1 − 1.5
THA (E5 − 3) − E2 (E5 − 9)L − Y ↔ BR − BIdling, Intake air temp. 20° C (68° F)0.5 − 3.4
THW (E5 − 4) − E2 (E5 − 9) R − W↔BR − BIdling, Engine coolant temp. 80 °C (176°F)0.2 − 1.0
STA (E7 − 11) − E1 (E4 − 24)B − R ↔ BR − BCranking6.0 or more
#10 (E4 − 12) − E01 (E4 − 13)W − L ↔ BR
IG switch ON9 − 14
IdlingPulse generation
(See page DI−54)
#20 (E4 − 11) − E01 (E4 − 13)W − R ↔ BR
IG switch ON9 − 14
IdlingPulse generation
(See page DI−54)
#30 (E4 − 25) − E01 (E4 − 13)W − G ↔ BR
IG switch ON9 − 14
IdlingPulse generation
(See page DI−54)
#40 (E4 − 2) − E01 (E4 − 13)Y ↔ BR
IG switch ON9 − 14
IdlingPulse generation
(See page DI−54)
#50 (E4 − 1) − E01 (E4 − 13)Y − R ↔ BR
IG switch ON9 − 14
IdlingPulse generation
(See page DI−54)
#60 (E4 − 15) − E01 (E4 − 13)Y − L ↔ BR
IG switch ON9 − 14
IdlingPulse generation
(See page DI−54)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−18
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
IGT (E4 −
23) − E1 (E4 − 24)
B − G ↔ BR − BIdlingPulse generation
(See page DI−97)
IGF (E4 − 17) − E1 (E4 − 24)B − Y ↔ BR − B
IG switch ON
Disconnect igniter connector4.5 − 5.5
IdlingPulse generation
(See page DI−97)
G1 (E6 − 11) − G − (E6 − 6)R ↔LIdlingPulse generation
(See page DI−62)
G2 (E6 − 10) − G − (E6 − 6)G ↔LIdlingPulse generation
(See page DI−62)
NE (E6 − 12) − G − (E6 − 6)W ↔LIdlingPulse generation
(See page DI−62)
NE2 (E6 − 5) − G − (E6 − 6)BR ↔ LIdlingPulse generation
(See page DI−62)
W (E7 − 4) − E1 (E4 − 24)Y − R ↔ BR − BIdling9 − 14
IG switch ON0 − 3
EGR (E4 − 22) − E1 (E4 − 24)L − W ↔ BR − BIG switch ON9 − 14
ISC1 (E4 − 7) − E01 (E4 − 13)R − G ↔ BRIG switch ON9 − 14
ISC2 (E4 − 6) − E01 (E4 − 13)R − B ↔ BRIG switch ON9 − 14
ISC3 (E4 − 5) − E01 (E4 − 13)G − Y ↔ BRIG switch ON9 − 14
ISC4 (E4 − 4) − E01 (E4 − 13)L − Y ↔ BRIG switch ON9 − 14
OX1 (E5 − 5) − E1 (E4 − 24)L ↔ BR − BMaintain engine speed at 2,500 rpm for 2 mins. after
warming upPulse generation
OX2 (E5 − 13) − E1 (E4 − 24)W ↔ BR − BMaintain engine speed at 2,500 rpm for 2 mins. after
warming upPulse generation
HT1 (E6 − 1) − E03 (E6 − 16)GR↔BRIdlingBelow 3.0
IG switch ON9 − 14
HT2 (E6 − 7) − E03 (E6 − 16)O↔ BRIdlingBelow 3.0
IG switch ON9 − 14
KNK1 (E5 − 6) − E1 (E4 − 24)W ↔BR − BIdlingPulse generation
(See page DI−62)
KNK2 (E5 − 14) − E1 (E4 − 24)L − W ↔ BR − BIdlingPulse generation
(See page DI−62)
SPD (E7 − 8) − E1 (E4 − 24)L − W ↔ BR − BIG switch ON
Rotate driving wheel slowly.Pulse generation
TE1 (E5 − 7) − E1 (E4 − 24)L↔ BR − BIG switch ON9 − 14
A/C (E7 − 7) − E1 (E4 − 24)B − W↔BR − BIdling, A/C switch ON9 − 14
Idling, A/C switch OFFBelow 2.0
THG (E4 − 19) − E2 (E5 − 9)G − Y↔ BR − BIG switch ON4.5 − 5.5
FC (E4 − 14) − E1 (E4 − 24)R − W↔BR − BIG switch ON9 − 14
Idling0 − 3
FPU (E4 − 21) − E1 (E4 − 24)L − R ↔BR − BIG switch ON9 − 14
Restarting at high engine coolant temp.0 − 3
SDL (E7 − 6) − E1 (E4 − 24)W ↔BR − BDuring transmissionPulse generation
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OY−03
−
DIAGNOSTICS ENGINE
DI−19
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
When the malfunction code is not confirmed in the DTC check and the problem \
still can not be confirmed
in the basic inspection, then proceed to this step and perform troubleshooting according to the numbered
order given in the table below.
SymptomSuspect AreaSee page
Engine does not crank (Does not start)1. Starting systemST−16
No initial combustion (Does not start)1. ECM power source circuit
2. Fuel pump control circuitDI−11 0
DI−11 5
No complete combustion (Does not start)1. Fuel pump control circuitDI−11 5
Engine cranks normally (Difficult to start)
1. Starter signal circuit
2. Fuel pump control circuit
3. CompressionDI−103
DI−11 5 EM−3
Cold engine (Difficult to start)1. Starter signal circuit
2. Fuel pump control circuitDI−103DI−11 5
Hot engine (Difficult to start)
1. Starter signal circuit
2. Fuel pressure control circuit
3. Fuel pump control circuitDI−103
DI−125DI−11 5
High engine idle speed (Poor idling)1. A/C signal circuit
2. ECM power source circuitAC−5
DI−11 0
Low engine idle speed (Poor idling)1. A/C signal circuit
2. Fuel pump control circuitAC−5
DI−11 5
Rough idling (Poor idling)1. Compression
2. Fuel pump control circuitEM−3
DI−11 5
Hunting (Poor idling)1. ECM power source circuit
2. Fuel pump control circuitDI−11 0
DI−11 5
Hesitation/Poor acceleration (Poor driveability)1. Fuel pump control circuit
2. A/T faultyDI−11 5
DI−147
Surging (Poor driveability)1. Fuel pump control circuitDI−11 5
Soon after starting (Engine stall)1. Fuel pump control circuitDI−11 5
During A/C operation (Engine stall)1. A/C signal circuit
2. Engine control module (ECM)AC−5
IN−18
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OZ−02
A00152
Output Voltage
Power Transistor
B+
Thermistor
Platinum Hot Wire
A B
Thermistor Platinum Hot Wire
FI6929 P22263
DI−20
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
CIRCUIT INSPECTION
DTC P0100 Mass Air Flow Circuit Malfunction
CIRCUIT DESCRIPTION
The mass air flow meter uses a platinum hot wire. The hot wire air flow met\
er consists of a platinum hot wire,
thermistor and a control circuit installed in a plastic housing. The hot wire air f\
low meter works on the principle
that the hot wire and thermistor located in the intake air bypass of the hou\
sing detect any changes in the
intake air temperature.
The hot wire is maintained at the set temperature by controlling the curren\
t flow through the hot wire. This
current flow is then measured as the output voltage of the air flow mete\
r.
The circuit is constructed so that the platinum hot wire and thermistor pro\
vide a bridge circuit, with the power
transistor controlled so that the potential of ”A” and ”B” remains equ\
al to maintain the set temperature.
DTC No.DTC Detecting ConditionTrouble Area
P0100Open or short in mass air flow meter circuit with engine
speed 4,000 rpm or less. Open or short in mass air flow meter circuit
 Mass air flow meter
 ECM
If the ECM detects DTC” P0100” it operates the fail safe function, k\
eeping the ignition timing and injection
volume constant and marking it possible to drive the vehicle.
HINT:
After confirming DTC P0100 use the OBD II scan tool or TOYOTA hand −held tester to confirm the mass air
flow ratio from ”CURRENT DATA”.
Mass Air Flow Value (gm/sec.)Malfunction
Approx. 0Mass air flow meter power source open
 VG circuit open or short
439.0 or moreE21 circuit open
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22419
WR−Y
GECM
Y−R R
R
BR
Battery Fusible Link
EFI
R/B No.2
EFI Main
Relay
Y−R
FL MAIN
BR
1
Mass Air Flow
Meter
2
2 2
2 2
2
1 1
1
F8 2
4
3 E7
E5
E5 VGMRLY
2
23
7
5 16B+
E1
EB
E21
EB1 EA2
−
DIAGNOSTICS ENGINE
DI−21
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010