1996 TOYOTA LAND CRUISER air condition

N14294
AC2SJ−01
−
AIR CONDITIONING AIR CONDITIONING AMPLIFIER
AC−75
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE GLOVE COMPARTMENT DOOR
(See page BO−76 )
2. REMOVE A/C AMPLIFIER
(a) Disconnect the connector from the amplifier.
(b) Remove the screw and the amplifier.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2SK−01
AC−76
−
AIR CONDITIONING AIR CONDITIONING AMPLIFIER
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal See page AC−75).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z04536
AC2SO−04
Z15447
−
AIR CONDITIONING REAR HEATER SWITCH
AC−77
1404
Author: Date:
1996 LAND CRUISER (RM451U)
REAR HEATER SWITCH
INSPECTION
1. REMOVE INSTRUMENT CLUSTER FINISH CENTER
PANEL WITH A/C CONTROL ASSEMBLY
2. REMOVE REAR HEATER SWITCH
3. INSPECT INDICATOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
5 and the negative ( −) lead to terminal 1.
(b) Push each of the rear heater switch knob in and check
that their indicators lights up.
If operation is not as specified, replace the switch.
4. INSPECT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
HI1 − 4Continuity
OFF−No Continuity
LO1 − 2Continuity
Illumination circuit3 − 6Continuity
If continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N09214
DI−4
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
The diagnosis system operates in normal mode
during normal vehicle use. It also has a check mode
for technicians to simulate malfunction symptoms
and troubleshoot. Most DTC use 2 trip detection
logic* to prevent erroneous detection, and ensure
thorough malfunction detection. By switching the
ECM to check mode when troubleshooting, the
technician can cause the MIL to light up for a mal-
function that is only detected once or momentarily
(TOYOTA hand−held tester only) (See step 2).
*2 trip detection logic:
When a logic malfunction is first detected, the mal-
function is temporarily stored in the ECM memory.
If the same malfunction is detected again during the
second drive test, this second detection causes the
MIL to light up.
The 2 trip repeats the same mode a 2nd time (How-
ever, the IG switch must be turned OFF between the
1st trip and 2nd trip.).
Freeze frame data:
Freeze frame data records the engine condition
when a misfire (DTC P0300 − P0306) or fuel trim
malfunction (DTC P0171, P0172) or other malfunc-
tion (first malfunction only), is detected.
Because freeze frame data records the engine
conditions (fuel system, calculator load, engine
coolant temperature, fuel trim, engine speed, ve-
hicle speed, etc.) when the malfunction is detected,
when troubleshooting it is useful for determining
whether the vehicle was running or stopped, the en-
gine warmed up or not, the air− fuel ratio lean or rich,
etc. at the time of the malfunction.
Priorities for troubleshooting:
If troubleshooting priorities for multiple DTCs are given in the
applicable diagnostic chart, these should be followed.
If no instructions are given troubleshoot DTCs according to the
following priorities. (1) DTC other than fuel trim malfunction (DTC P0171,
P0172), EGR (DTC P0401, P0402), and misfire
(DTC P0300 − P0306).
(2) Fuel trim malfunction (DTC P0171, P0172), and EGR (DTC P0401, P0402).
(3) Misfire (DTC P0300 − P0306).
(b) Check the DLC3. The vehicle’s ECM uses V.P.W. (V ariable Pulse Width) for
communication to comply with SAE J1850. The terminal
arrangement of DLC3 complies with SAE J1962 and
matches the V.P.W. format.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI3605
ON
OFF Flashing
0.13 Second
DI−6
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand −held tester) to check the DTC, use
normal mode. For codes on the DTC chart subject to ”2 trip
detection logic”, turn the ignition switch OFF after the
symptom is simulated the first time. Then repeat the simu-
lation process again. When the problem has been simu-
lated twice, the MIL lights up and the DTCs are recorded in
the ECM.
3. INSPECT DIAGNOSIS (CHECK MODE)
HINT:
TOYOTA hand−held tester only:
Compared to the normal mode, the check mode has an in-
creased sensitivity to detect malfunctions.
Furthermore, the same diagnostic items which are detected in
the normal mode can also be detected in the check mode.
(a) Check the DTC. (1) Initial conditions
Battery positive voltage 11 V or more.
Throttle valve fully closed.
Transmission in ”park” or ”neutral” position.
Air conditioning switched OFF.
(2) Turn ignition switch OFF.
(3) Prepare the TOYOTA hand−held tester.
(4) Connect the TOYOTA hand−held tester to DLC3 in
the fuse box at the lower left of the instrument panel.
(5) Turn the ignition switch ON and push the TOYOTA hand−held tester ON.
(6) Switch the TOYOTA hand −held tester normal mode
to check mode (Check that the MIL flashes.).
(7) Switch the engine (The MIL goes out after the en- gine start.).
(8) Simulate the conditions of the malfunction de- scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTC, etc. (9) After simulating the malfunction conditions, use theTOYOTA hand−held tester diagnosis selector to
check the DTCs and freezed frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. T urning the ignition
switch OFF switches the diagnosis system from check mode to
normal mode, so all DTCs, etc. are erased.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−7
1996 LAND CRUISER (RM451U)
(10) After checking the DTC, inspect the applicable cir-
cuit.
(b) Clear the DTC.
The following actions will erase the DTCs and freezed
frame data.
(1) Operating the OBD II scan tool (complying with SAE
J1978) or TOYOTA hand−held tester to erase the
codes. (See the OBD II scan tool’ s instruction book
for operating instructions.)
(2) Disconnecting the battery terminals or EFI fuse.
NOTICE:
If the TOYOTA hand −held tester switches the ECM from
normal mode to check mode or vice −versa, or if the igni-
tion switch is turned from ON to ACC or LOCK during check
mode, the DTCs and freezed frame data will be erased.
4. FAIL−SAFE CHART
If any of the following codes is recorded, the ECM enters fail −safe mode.
DTC No.Fail−Safe OperationFail− Safe Deactivation Conditions
P0100Ignition timing fixed at 5 ° BTDC
 Injection method fixed at simultaneous injectionReturned to normal condition
P0110Intake air temp. is fixed at 20° C (68°F)Returned to normal condition
P0115Engine coolant temp. is fixed at 80 °(176°F)Returned to normal condition
P0120VTA is fixed at 0°
The following condition must be repeated at least 2 times
consecutively
When closed throttle position switch is ON:
0.1 V  VTA  0.95 V
P0135
P0141The heater circuit in witch an abnormality is detected is
turned offIgnition switch OFF
P0325
P0330Max. timing retardationIgnition switch OFF
P1300Fuel cutIGF signal is detected for 6 consective ignitions
P1605Max. timing retardationReturned to normal condition
5. CHECK FOR INTERMITTENT PROBLEMS
TOYOTA hand−held tester only:
By putting the vehicle’s ECM in check mode, 1 trip detection logic is possible instead of 2 trip detection logic
and sensitivity to detect open circuits is increased. This makes it easier \
to detect intermittent problems.
(1) Clear the DTC (See step 2).
(2) Set the check mode (See step 3).
(3) Perform a simulation test (See page IN−18).
(4) Check the connector and terminal (See page IN−28).
(5) Handle the connector (See page IN−28).
(6) Visual check and contact pressure (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00149
DLC1
E1
TE1 SST
P09137
P23430
−
DIAGNOSTICS ENGINE
DI−9
1996 LAND CRUISER (RM451U)
OK
5 Check idle speed.
PREPARATION:
(a) Warm up engine to normal operating temperature.
(b) Switch off all accessories.
(c) Switch off air conditioning.
(d) Shift transmission into ”N” position.
(e) Connect the OBD II scan tool or TOYOTA hand−held tester to DLC3 on the vehicle.
CHECK:
Use CURRENT DATA to check the idle speed.
OK:
Idle speed: 650 ± 50 rpm
NG Proceed to matrix chart of problem symptomson page DI−19.
OK
6 Check ignition timing.
PREPARATION:
(a) Warm up engine to normal operating temperature.
(b) Shift transmission into ”N” position.
(c) Keep the engine speed at idle.
(d) Using SST, connect terminals TE1 and E1 of DLC1. SST 09843−18020
(e) Connect a timing light probe to a high −tension cord.
CHECK:
Check ignition timing.
OK:
Ignition timing: 3 ° BTDC at idle
NG Proceed to page IG−1 and continue to trouble-
shoot.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−11
1996 LAND CRUISER (RM451U)
NG Proceed to page IG−1 and continue to trouble-
shoot.
OK
Proceed to matrix chart of problem symp-
toms on page DI−19.
7. ENGINE OPERATING CONDITION
NOTICE:
The values given below for ”Normal Condition” are representative valu\
es, so a vehicle may still be
normal even if its value varies from those listed here. So do not decide wheth\
er a part is faulty or
not solely according to the ”Normal Condition” here.
(a) CARB mandated signals.
TOYOTA hand−held tester displayMeasurement ItemNormal Condition*
FUEL SYS #1
Fuel System Bank 1
OPEN: Air− fuel ratio feedback stopped
CLOSED: Air− fuel ratio feedback operating
Idling after warming up: CLOSED
CALC LOAD
Calculator Load:
Current intake air volume as a proportion of max.
intake air volumeIdling: 13.8 − 19.3%
Racing without load (2,500 rpm): 17.6 − 25.2%
COOLANT TEMP.Engine Coolant Temp. Sensor ValueAfter warming up: 80 − 95° C (176 − 203°F)
SHORT FT #1Short−term Fuel Trim Bank 10 ± 20%
LONG FT #1Long−term Fuel Trim Bank 10 ± 20%
ENGINE SPDEngine SpeedIdling: 650 ± 50 rpm
VEHICLE SPDVehicle SpeedVehicle Stopped: 0 km/h (0 mph)
IGN ADVANCEIgnition Advance:
Ignition Timing of Cylinder No. 1Idling: BTDC 0 − 11°
INTAKE AIRIntake Air Temp. Sensor V alueEquivalent to Ambient Temp.
MAFAir Flow Rate Through Mass Air Flow Meter
Idling: 4.3 − 6.1 gm/sec.
Racing without load (2,500 rpm):
21.2 − 30.4 gm/sec.
THROTTLE POS
Voltage Output of Throttle Position Sensor
Calculated as a percentage:
0 V → 0%, 5 V →100%Throttle Fully Closed: 7 − 11 %
Throttle Fully Open: 65 − 75%
O2S B1, S1Voltage Output of Oxygen Sensor
Bank 1, Sensor 1Idling: 0.1 − 0.9 V
O2FT B1, S1Oxygen Sensor Fuel Trim Bank 1, Sensor 1
(Same as SHORT FT #1)0 ± 20%
O2S B1, S2Voltage Output of Oxygen Sensor
Bank 1, Sensor 2Driving (50 km/h, 31 mph): 0.1 − 0.9 V
∗: If no conditions are specifically stated for ”ldling”, it means \
the shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010