1996 TOYOTA CAMRY light

11 0For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Press in the air conditioning on-off but-
ton.
(d) Ventilation
1. Turn the temperature control knob at
the LOW position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Turn the air flow control knob to the
FACE position.
For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.
(e) Windshield defogging and defrost-
ing
To remove interior fog on the windshield:
1. Turn the temperature control knob to
any position.
2. Move the air intake control lever to the
OUTSIDE AIR position.3. Turn the air flow control knob to the
WINDSHIELD position.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Press in the air conditioning on-off but-
ton.
To remove frost or exterior fog on the
windshield:
1. Turn the temperature control knob to
the HIGH position.
2. Move the air intake control lever to the
OUTSIDE AIR position.
3. Turn the air flow control knob to the
WINDSHIELD position.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Turn the fan speed control knob to the
HIº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.
(f) Air flow selection
FACE positionÐThis position directs the
air flow to face level.BI-LEVEL positionÐThis position directs
the air flow to face level and the floor. Ex-
cept in ventilation, the air to the floor is
slightly warmer than that to face level.
FLOOR positionÐThis position directs air
flow mostly to the floor.
FLOOR/WINDSHIELD position Ð This
position directs the air flow to the wind-
shield as well as the floor.
WINDSHIELD positionÐThis position di-
rects air flow mostly to the windshield and
front side windows.
Do not use the WINDSHIELD position
during cooling operation in extremely hu-
mid weather. The difference between the
temperature of the outside air and that of
the windshield could cause the outer sur-
face of the windshield to fog up, blocking
your vision.
(g) Operating tips

Be sure the air inlet grilles in front of the
windshield are not blocked by leaves
or other obstructions.

If air flow control is not satisfactory,
check the dashboard vents. (See
Side ventsº or Lower ventº after
Heater controlsº.)ProCarManuals.com

11 4(a) Controls and functions
The temperature control knob is used to
adjust the temperature of the delivered
air.
Turn the knob toward the HIGH position
for higher temperature and toward the
LOW position for lower temperature.
The air intake control button is used to se-
lect intake air, either outside air or recircu-
lated air.
With the button in the OUTSIDE AIR
mode, the system will take fresh outside
air into the unit. For recirculated air, set
the button to the RECIRCULATED AIR
mode. Pressing the button once again will
let the button out in the OUTSIDE AIR
mode.
The air flow control buttons are used to
select the air flow outlets air is delivered
from.
See (f) Air flow selectionº for detailed in-
formation.
The fan speed control knob is used to turn
on and off the fan and select the fan
speed.
The higher the fan speed setting is, the
more air is delivered. Turning the knob to
the OFFº position turns off the fan.
The air conditioning on-off button is used
to turn on and off the air conditioning.With the button pressed in, the air condi-
tioning turns on. Pressing the button once
again will turn the air conditioning off.
If the indicator light flashes, contact your
Toyota dealer as soon as possible. There
may be slippage of the drive belt or trouble
in the compressor. If this happens, the air
conditioning is automatically turned off to
avoid damage to the drive belt.
(b) Heating
1. Turn the temperature control knob
anywhere except the LOW position.
When dehumidified heating is desired,
turn the knob between the HIGH and
middle positions.
If cooler air is desired at face level for bi-
level operation, place the knob around the
middle.
2. If quick circulation of heated air is de-
sired, set to the RECIRCULATED AIR
mode of the air intake control button.
For normal use, it is best to set to the
OUTSIDE AIR mode. Otherwise the win-
dows will fog up more easily.
3. Press in the FLOOR button of the air
flow control buttons.
If cooler air is desired at face level for bi-
level operation, press in the BI-LEVEL
button.If the windshield fogs up easily, press in
the FLOOR/WINDSHIELD button.
For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.
If dehumidified heating is desired, press in
the air conditioning on-off button.
(c) Cooling
1. Turn the temperature control knob
anywhere between the middle and LOW
positions.
If warmer air is desired at floor level for bi-
level operation, turn the knob around the
middle.
2. If quick circulation of cooled air is de-
sired, set to the RECIRCULATED AIR
mode of the air intake control button.
For normal use, it is best to set to the
OUTSIDE AIR mode.
3. Press in the FACE button of the air flow
control buttons.
If warmer air is desired at floor level for bi-
level operation, press in the BI-LEVEL
button.ProCarManuals.com

11 5 For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Press in any fan speed control button
except the OFFº button.
5. Press in the air conditioning on-off but-
ton.
(d) Ventilation
1. Turn the temperature control knob at
the LOW position.
2. Set to the OUTSIDE AIR mode of the
air intake control buttons.
3. Press in the FACE button of the air flow
control buttons.
For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.
(e) Windshield defogging and defrost-
ing
To remove interior fog on the windshield:
1. Turn the temperature control knob to
any position.
2. Set to the OUTSIDE AIR mode of the
air intake control buttons.3. Press in the WINDSHIELD button of
the air flow control buttons.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Press in the air conditioning on-off but-
ton.
To remove frost or exterior fog on the
windshield:
1. Turn the temperature control knob to
the HIGH position.
2. Set to the OUTSIDE AIR mode of the
air intake control buttons.
3. Press in the WINDSHIELD button of
the air flow control buttons.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Turn the fan speed control knob to the
HIº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.
(f) Air flow selection
FACE buttonÐThis button directs the air
flow to face level.
BI-LEVEL buttonÐThis button directs
the air flow to face level and the floor. Ex-
cept in ventilation, the air to the floor is
slightly warmer than that to face level.FLOOR buttonÐThis button directs air
flow mostly to the floor.
FLOOR/WINDSHIELD buttonÐThis but-
ton directs air flow to the windshield as well
as the floor.
WINDSHIELD buttonÐThis button di-
rects air flow mostly to the windshield and
front side windows.
Do not use the WINDSHIELD button dur-
ing cooling operation in extremely humid
weather. The difference between the tem-
perature of the outside air and that of the
windshield could cause the outer surface
of the windshield to fog up, blocking your
vision.
(g) Operating tips

Be sure the air inlet grilles in front of the
windshield are not blocked by leaves
or other obstructions.

If air flow control is not satisfactory,
check the dashboard vents. (See
Side ventsº or Lower ventº after
Heater controlsº.)

To help cool down the interior after
parking in the hot sun, drive for the first
few minutes with the windows open.
After the excess heat has blown away,
close the windows.ProCarManuals.com

120BI-LEVEL positionÐThis position directs
the air flow to face level and the floor. Ex-
cept in ventilation, the air to the floor is
slightly warmer than that to face level.
FLOOR positionÐThis position directs
the air flow mostly to the floor.
FLOOR/WINDSHIELD position Ð This
position directs air flow to the wind-
shield as well as the floor.
WINDSHIELD positionÐThis position di-
rects air flow to the windshield and front
side windows.
(f) Operating tips

Be sure the air inlet grilles in front of the
windshield are not blocked by leaves
or other obstructions.

If air flow control is not satisfactory,
check the dashboard vents. (See
Side ventsº or Lower ventº.)

When driving on dusty roads, close all
windows. If dust thrown up by the ve-
hicle is still drawn into the vehicle after
closing the windows, it is recom-
mended that the air intake control le-
ver be set to the OUTSIDE AIR posi-
tion and the fan speed control knob
anywhere except the OFFº position.
If following another vehicle on a dusty
road, or driving in windy and dusty con-
ditions, it is recommended that the air
intake control lever be temporarily set
to the RECIRCULATED AIR position,
which will close off the outside pas-
sage and prevent outside air and dust
from entering the vehicle interior.
The side vents may be opened or
closed as shown.
Side vents
ProCarManuals.com

Part 1Cigarette lighter and ashtray Clock
123
OPERATION OF
INSTRUMENTS
AND CONTROLSÐ
Chapter 1-8
Other equipment

Clock

Cigarette lighter and ashtray

Glovebox

Miscellany holder

Cup holder

Luggage cover

Parcel straps

Floor mat
The digital clock indicates the time
with the ignition key at the ACCº or
ONº position. To reset the hour, de-
press the Hº button. To reset the min-
utes, depress the Mº button. To ad-
just the time to a full hour, depress the
:00º button.
For example, if the :00º button is de-
pressed when the time is between
1:01Ð1:29, the time will change to 1:00.
If the time is between 1:30Ð1:59, the time
will change to 2:00.
When the instrument panel lights are
turned on, the brightness of the time indi-
cation will be reduced.
Once the electrical power source has
been disconnected from the clock, the
time is automatically set to 1:00 (one
o'clock).To use the cigarette lighter, press it in.
When it becomes heated, it automati-
cally pops out ready for use.
If the engine is not running, the key must
be in the ACCº position.
Do not hold the cigarette lighter pressed
in.
When finished with your cigarette, thor-
oughly extinguish it in the ashtray to pre-
vent other cigarette butts from catching
fire. After using the ashtray, push it back
in completely.
To remove the ashtray, press down on the
lock spring plate and pull out.
Use a Toyota genuine cigarette lighter or
equivalent for replacement.
ProCarManuals.com

124
To reduce the chance of injury in
case of an accident or sudden stop
while driving, always push the ash-
tray back in completely after using.CAUTION
!
To open the glovebox door, pull the le-
ver. To lock the glovebox door, insert
the master key and turn it clockwise.
With the instrument panel lights on, the
glovebox light will come on when the door
is open.
To reduce the chance of injury in
case of an accident or a sudden
stop, always keep the glovebox
door closed while driving.CAUTION
!
To open the holder, pull the lever as
shown above.
To reduce the chance of injury in
case of an accident or a sudden
stop, always keep the miscellany
holder closed while driving.CAUTION
! Miscellany holder Glovebox
ProCarManuals.com

130Use of unleaded fuel with an octane num-
ber or rating lower than stated above will
cause persistent heavy knocking. If se-
vere, this will lead to engine damage.
If your engine knocks...
If you detect heavy knocking even when
using the recommended fuel, or if you
hear steady knocking while holding a
steady speed on level roads, consult your
Toyota dealer.
However, now and then, you may notice
light knocking for a short time while accel-
erating or driving up hills. This is no cause
for concern.
GASOLINES CONTAINING DETER-
GENT ADDITIVES
Toyota recommends use of gasolines
that contain detergent additives to
avoid build-up of engine deposits.
For further details, ask your Toyota dealer
or a local gasoline retailer.
GASOLINES CONTAINING MTBE
Gasolines that contain MTBE (Methyl
Tertiary-Butyl Ether) are available in
the market. If you use a gasoline mixed
with MTBE, make certain that it does
not contain more than 15% of MTBE.If the use of gasolines containing MTBE
causes poor driveability and/or poor fuel
economy, you should discontinue the use
of fuels containing MTBE.
GASOLINES CONTAINING ALCOHOL
If you use gasohol in your Toyota, be
sure that it is unleaded, has an octane
rating no lower than 87 and does not
contain more than 10% ethanol.
Gasohol is a mixture of gasoline and etha-
nol.
Toyota does not recommend the use of
gasolines containing methanol. If you use
gasoline containing methanol, use only
gasoline meeting the requirements above
and also containing less than 5% metha-
nol with cosolvents and corrosion inhibi-
tors for methanol.
NOTICE
Do not use gasohol other than
stated above. It will cause fuel
system damage or vehicle perfor-
mance problems.
If driveability problems are en-
countered (poor hot starting, va-
porizing, engine knock, etc.), dis-
continue the use.
Take care not to spill gasohol dur-
ing refueling. Gasohol may cause
paint damage.
FUEL TANK CAPACITY
70 L (18.5 gal., 15.4 Imp. gal.)If you plan to drive your Toyota in
another country...
First, comply with the vehicle registration
laws.
Second, confirm the availability of the
correct fuel (unleaded and minimum oc-
tane number).
Operation in foreign countries
ProCarManuals.com

134TANDEM MASTER CYLINDER BRAKE
SYSTEM
The tandem master cylinder brake sys-
tem is a hydraulic system with two sepa-
rate sub-systems. If either sub-system
should fail, the other will still work. Howev-
er, the pedal will be harder to press, and
your stopping distance will be longer.
Also, the brake system warning light may
come on.
CAUTION!
Do not drive your vehicle with only
a single brake system. Have your
brakes fixed immediately.
BRAKE BOOSTER
The brake booster uses engine vacuum to
power-assist the brakes. If the engine
should quit while you are driving, you can
bring the vehicle to a stop with normal
pedal pressure. There is enough reserve
vacuum for one or two stopsÐbut no
more!
CAUTION!

Do not pump the brake pedal if the
engine stalls. Each push on the
pedal uses up your vacuum re-
serve.

Even if the power assist is com-
pletely lost, the brakes will still
work. But you will have to push the
pedal hardÐmuch harder than
normal. And your braking distance
will be longer.
ANTI-LOCK BRAKE SYSTEM (with
ABSº warning light)
The anti-lock brake system is designed to
prevent lock-up of the wheels during sud-
den braking or braking on slippery road
surfaces. This assists the driver in con-
trolling the vehicle under these circum-
stances.
The anti-lock brake system becomes op-
erative after the vehicle has accelerated
to a speed in excess of approximately 10
km/h (6 mph). It stops operating when the
vehicle decelerates to a speed below
approximately 5 km/h (3 mph).
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
is started. This means that the anti-lock
brake system is in the self check mode,
and does not indicate a malfunction.
When the anti-lock brake system function
is in action, you may feel the brake pedal
pulsating and hear a noise. In this situa-
tion, to let the anti-lock brake system
work for you, just hold the brake pedal
down more firmly. Do not pump the brake.The brake pedal pulsation caused by the
anti-lock brake system may indicate haz-
ardous road surface conditions. Although
the anti-lock brake system assists in pro-
viding vehicle control, it is still important to
drive with all due care, because the anti-
lock brake system cannot overcome the
laws of physics that act on your vehicle:

Braking capability is dependent on tire
friction with the road surface.

Even though the anti-lock brake sys-
tem is operating, a driver cannot main-
tain full control on certain slippery road
surfaces, when cornering at high
speeds, or in violent maneuvers.

Avoid high speeds on wet roads. The
anti-lock brake system cannot elimi-
nate the risk of hydroplaning and loss
of tire friction.
Always maintain a safe distance from the
vehicle in front of you. Compared with ve-
hicles not fitted with an anti-lock brake
system, your vehicle may require a longer
stopping distance in the following cases:

Driving on rough, gravel or snow-cov-
ered roads.

Driving with tire chains installed.

Driving on roads where the road sur-
face is pitted or has other differences
in surface height.
Brake system
ProCarManuals.com