1996 SUBARU LEGACY tightening

H2M1460
7) Remove two screws fixing bracket on fuel pump assem-
bly.
H2M1461A
8) Remove one screw fixing fuel level sensor on bracket.
9) Remove fuel level sensor from fuel pump assembly.
B2M0955A
B: INSTALLATION
CAUTION:
Leave fuel filler cap open when tightening nuts, to pre-
vent fuel from flowing out through fuel delivery and
return pipes. Close fuel filler cap after tightening nuts.
Installation is in the reverse order of removal. Do the fol-
lowing:
(1) Always use new gaskets.
(2) Ensure sealing portion is free from fuel or foreign
particles before installation.
(3) Tighten nuts in numerical sequence shown in Fig-
ure to specified torque.
Tightening torque:
4.4±1.5 N⋅m (0.45±0.15 kg-m, 3.3±1.1 ft-lb)
B2M0968
13. Air Filter (2200 cc AWD Model)
A: REMOVAL AND INSTALLATION
1) Remove canister.
2) Remove two hoses from air filter.
3) Remove flange nut from bracket.
4) Installation is in the reverse order of removal.
16
2-1SERVICE PROCEDURE
12. Fuel Level Sensor (2200 cc AWD Model) - 13. Air Filter (2200 cc AWD Model)

H2M1460
7) Remove two screws fixing bracket on fuel pump assem-
bly.
H2M1461A
8) Remove one screw fixing fuel level sensor on bracket.
9) Remove fuel level sensor from fuel pump assembly.
B2M0955A
B: INSTALLATION
CAUTION:
Leave fuel filler cap open when tightening nuts, to pre-
vent fuel from flowing out through fuel delivery and
return pipes. Close fuel filler cap after tightening nuts.
Installation is in the reverse order of removal. Do the fol-
lowing:
(1) Always use new gaskets.
(2) Ensure sealing portion is free from fuel or foreign
particles before installation.
(3) Tighten nuts in numerical sequence shown in Fig-
ure to specified torque.
Tightening torque:
4.4±1.5 N⋅m (0.45±0.15 kg-m, 3.3±1.1 ft-lb)
B2M0968
13. Air Filter (2200 cc AWD Model)
A: REMOVAL AND INSTALLATION
1) Remove canister.
2) Remove two hoses from air filter.
3) Remove flange nut from bracket.
4) Installation is in the reverse order of removal.
16
2-1SERVICE PROCEDURE
12. Fuel Level Sensor (2200 cc AWD Model) - 13. Air Filter (2200 cc AWD Model)

G2M0093
4) Connect oil pressure gauge hose to cylinder block.
5) Start the engine, and measure oil pressure.
Oil pressure:
98 kPa (1.0 kg/cm
2,14 psi) or more at 800 rpm
294 kPa (3.0 kg/cm2, 43 psi) or more at 5,000 rpm
CAUTION:

If oil pressure is out of specification, check oil
pump, oil filter and lubrication line.


If oil pressure warning light is turned ON and oil
pressure is in specification, replace oil pressure
switch.

NOTE:
The specified data is based on an engine oil temperature
of 80°C (176°F).
6) After measuring oil pressure, install oil pressure switch.
Tightening torque:
25±3 N⋅m (2.5±0.3 kg-m, 18.1±2.2 ft-lb)
7) Install generator and V-belt in the reverse order of
removal, and adjust the V-belt deflection.
8
2-2
6. Engine Oil Pressure

1. Timing Belt
B2M0102A

1Crankshaft sprocket


2Belt cover No. 2 (RH)


3Belt cover No. 2 (LH)


4Camshaft sprocket (RH)


5Belt idler


6Tensioner bracket


7Belt idler


8Belt tensioner


9Tensioner adjuster


10Belt idler No. 2


11Camshaft sprocket (LH)


12Timing belt

13Belt cover (RH)


14Front belt cover


15Belt cover (LH)


16Crankshaft pulley
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 5±1 (0.5±0.1, 3.6±0.7)
T2: 25±2 (2.5±0.2, 18.1±1.4)
T3: 39±4 (4.0±0.4, 28.9±2.9)
T4: 78±5 (8.0±0.5, 57.9±3.6)
T5: 108
+10
5(11+1.0
0.5, 79.6+7.2
3.6)
6
2-3COMPONENT PARTS
1. Timing Belt

2. Cylinder Head and Camshaft
B2M0103A

1Rocker cover (RH)


2Rocker cover gasket


3Camshaft support (RH)


4O-ring


5Camshaft (RH)


6Intake valve guide


7Exhaust valve guide


8Oil seal


9Cylinder head (RH)


10Cylinder head gasket


11Cylinder head (LH)


12Plug


13Camshaft (LH)


14O-ring


15Camshaft support (LH)

16Oil seal


17Oil filler cap


18Gasket


19Oil filler pipe


20O-ring


21Rocker cover gasket


22Rocker cover (LH)
Tightening torque: N⋅m (kg-m, ft-lb)
T1: Refer to 2-3 [W6E1].
T2: 5±1 (0.5±0.1, 3.6±0.7)
T3: 10 (1.0, 7)
T4: 16 (1.6, 12)
7
2-3COMPONENT PARTS
2. Cylinder Head and Camshaft

3. Cylinder Head and Valve Assembly
B2M0380A

1Exhaust valve


2Intake valve


3Intake valve oil seal


4Valve spring


5Retainer


6Retainer key


7Exhaust valve oil seal


8Rocker shaft support


9Rocker shaft support


10Rocker shaft support

11Rocker shaft


12Hydraulic lash adjuster


13Intake valve rocker arm


14Exhaust valve rocker arm


15Spring
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 5±1 (0.5±0.1, 3.6±0.7)
T2: 12±1 (1.2±0.1, 8.7±0.7)
8
2-3COMPONENT PARTS
3. Cylinder Head and Valve Assembly

4. Cylinder Block
B2M0381A

1Oil pressure switch


2Cylinder block (RH)


3Service hole plug


4Gasket


5Oil separator cover


6Water pipe


7Oil pump


8Front oil seal


9Rear oil seal


10O-ring


11Service hole cover


12Cylinder block (LH)


13Water pump


14Baffle plate


15Oil strainer stay


16Oil strainer

17Gasket


18Oil pan


19Oil drain plug


20Gasket


21Oil filler pipe
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 5 (0.5, 3.6)
T2: 6.4 (0.65, 4.7)
T3: 10 (1.0, 7)
T4: 25±2 (2.5±0.2, 18.1±1.4)
T5: 47±3 (4.8±0.3, 34.7±2.2)
T6: 69±7 (7.0±0.7, 50.6±5.1)
T7: First 12±2 (1.2±0.2, 8.7±1.4)
Second 12±2 (1.2±0.2, 8.7±1.4)
9
2-3COMPONENT PARTS
4. Cylinder Block

5. Crankshaft and Piston
G2M0105

1Drive plate (AT)


2Reinforcement (AT)


3Flywheel (MT)


4Bell bearing (MT)


5Top ring


6Second ring


7Oil ring


8Piston


9Piston pin


10Circlip


11Connecting rod bolt


12Connecting rod

13Connecting rod bearing


14Connecting rod cap


15Crankshaft


16Woodruff key


17Crankshaft bearing #1, #5


18Crankshaft bearing #2, #4


19Crankshaft bearing #3
Tightening torque: N⋅m (kg-m, ft-lb)
T1: 44±2 (4.5±0.2, 32.5±1.4)
T2: 72±3 (7.3±0.3, 52.8±2.2)
10
2-3COMPONENT PARTS
5. Crankshaft and Piston