1996 Mercury Villager window

98
[IP05900(ALL)01/93]2.
Turn the temperature control knob to COOL.
[IP06000(ALL)01/93]3.
Press the A/C button. The indicator light on the A/C button
will illuminate.
[IP06100(ALL)09/93]4.
The air intake selector button may be in the outside air
mode or the recirculated air mode. The recirculated air mode
is recommended for best A/C performance when the vehicle
interior is very warm. As interior air comfort is reached, you
may decide to switch to the outside air mode.
[IP06200(ALL)01/93]5.
Turn the fan speed knob to the position of your choice.
[IP06300(ALL)01/93]6.
If your vehicle is equipped with the rear passenger
compartment air conditioning unit, it will be on when the
front A/C is on and the rear climate control lever is set to
REAR, 1, 2, 3, or 4. Refer to the previous section for an
explanation of the heating system.
[IP06400(ALL)01/93]7.
Adjust your instrument panel registers.
[IP06500(ALL)04/94]8.
If the inside of your vehicle is very warm, you may want to
drive for a few minutes with the windows down and the air
conditioner on. This forces most of the hot, stale air out of
the vehicle and allows the air conditioner to cool down the
interior more quickly.
*
[IP06600(ALL)05/95]
The air conditioner may be used to cool the outside air being
drawn into your vehicle, but using recirculated air is more
economical and cools your vehicle more quickly.
[IP06700(ALL)07/93]
NOTE: The A/C button independently toggles the A/C
system's compressor signal and indicator light ON and
OFF in the Panel, Panel/Floor, Floor, Defrost and Mix
functions. The A/C button will not operate or light
when the system is set in the OFF position. The A/C
button will operate in defrost but will not override
previously discussed automatic operation.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996

Instrument Panel Controls
103
[IP10305(ALL)06/95]
Automatic Temperature Control System
[IP10310(ALL)06/95]
The control for your Automatic Temperature Control (ATC) is
located at the center of the instrument panel above the radio.
The ATC operates only when the ignition key is turned to the
ON position and the vehicle is running.
[IP10315(ALL)06/95]
17-1/2 pica art:0040072-E[IP10320(ALL)06/95]
To turn the ATC on, push the AUTOMATIC button or any of
the five airflow function selector buttons:P,V,Q,S,
orR.
[IP10323(ALL)06/95]
To turn the ATC off, press the OFF button.
[IP10325(ALL)06/95]
To change the temperature in the display window, select any
temperature between65ÊF (18ÊC) and 85ÊF (29ÊC)using the
NTEMPMbutton.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996

104
[IP10330(ALL)06/95]
The ATC maintains the temperature you select and
automatically controls the airflow for your comfort. It also
allows you to override the automatic operation of airflow and
fan speed with manual function selector buttons and the fan
speed dial.
[IP10335(ALL)06/95]
When you select the AUTOMATIC button, the system
determines airflow location and fan speed automatically. It also
automatically determines whether you will be receiving fresh
outside airflow, recirculated interior airflow, or a combination of
both. You can manually override the airflow source (outside or
recirculated air) and airflow location by selecting one of the
function selector buttons. You can also manually override the
fan speed by rotating the fan speed dial.
[IP10340(ALL)06/95]
Whether you operate in the AUTOMATIC mode or manually
override the AUTOMATIC mode settings, the ATC will continue
to maintain the air temperature you have selected. However, if
you choose to manually override the airflow location by
selecting one of the function selector buttons, you will also need
to select the A/C button if you desire cool air-conditioned air.
(Your ATC automatically operates the air conditioning [if
required] when you are in the AUTOMATIC mode without
illuminating the A/C button, but the system requires you to
manually select the A/C button if you desire A/C operation
when you manually override airflow location.)
[IP10350(ALL)06/95]
If you want continuous maximum cooling, push theNside of
the TEMP button until60ÊF (16ÊC)shows in the display
window. The ATC will cool at its maximum level and disregard
the 60ÊF (16ÊC)setting until a warmer temperature is selected. If
you want continuous maximum heating, push theMside of the
TEMP button until90ÊF (32ÊC)shows in the display window.
The ATC will provide maximum heat regardless of the90ÊF
(32ÊC) setting until a cooler temperature is selected.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996

Instrument Panel Controls
105
[IP10360(ALL)06/95]
The display window and the function selector buttons indicate
how the system is operating. The display window shows the
selected temperature and displays AUTO if you are operating in
the AUTOMATIC mode. If you override the automatic mode by
selecting any of the function selector buttons, AUTO no longer
appears in the display window and the appropriate function
selector button(s) illuminate. The display window also indicates
manual (thumbwheel) control of the fan speed when a
His
shown.
[IP10370(ALL)06/95]
Automatic Operation
[IP10380(ALL)06/95]
Push the AUTOMATIC button and select the desired
temperature. The selected temperature and AUTO appear in the
display window. The ATC heats or cools to achieve the set
temperature. It is important to note that if the ATC engages
your vehicle's air-conditioning, it will do so automatically
without illuminating the A/C button.
[IP10390(ALL)06/95]
When in AUTOMATIC and weather conditions require heat, air
is sent to the floor. However, a feature is included in the ATC
to prevent blowing cold air to the floor if the engine coolant is
not warm enough to provide heating. Within three or four
minutes (of determining the engine coolant is not warm enough)
the fan speed gradually increases and airflow changes to the
floor.
[IP10400(ALL)06/95]
If specific conditions exist (such as window fogging) the five
override buttons allow specific airflow selection. The
thumbwheel allows you to adjust the fan speed to suit your
needs.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996

106
[IP10410(ALL)06/95]
Temperature Selection
[IP10420(ALL)06/95]
TheNTEMPMbutton on the left side of the control panel is
for temperature selection. TheNside lowers the set
temperature, and theMside raises the set temperature. Press
and hold either side of the button to rapidly change the
temperature setting in one degree increments to either65ÊF
(18ÊC) or 85ÊF (29ÊC).Then, the set temperature jumps 5ÊF and
stops at either60ÊF (16ÊC),which is maximum cooling, or90ÊF
(32ÊC),which is maximum heating.
[IP10423(ALL)05/96]
Changing the Display Mode (English/Metric)
[IP10425(ALL)05/96]
To switch between the English and Metric display mode, press
the DEFROST and A/C buttons simultaneously while rotating
the fan speed dial upward until it stops moving. After one
second, the display will begin to toggle between English and
Metric.
[IP10430(ALL)06/95]
Fan Speed and Thumbwheel
[IP10440(ALL)06/95]
The ATC automatically adjusts the fan speed to the existing
conditions. To control the fan speed yourself, use the
thumbwheel located at the extreme right side of the ATC
control panel. Using the thumbwheel cancels the automatic fan
speed control, and causes a
Hto appear in the display window.
Rotate the thumbwheel up for HI speeds and down for LO
speeds.
[IP10450(ALL)06/95]
To return to auto fan control, press the AUTOMATIC button.
[IP10460(ALL)06/95]
Airflow Function Selector Buttons
[IP10470(ALL)06/95]
Your ATC has five buttons which allow you to make special
selections for airflow. The buttons are grouped in the middle of
the ATC panel and allow you to determine airflow location.
Pressing any of the function selector buttons illuminates the
button pushed and directs airflow to the appropriate location.
The temperature of the airflow will still be automatically
controlled. Return to fully automatic operation by pushing the
AUTOMATIC button.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996

Instrument Panel Controls
107
[IP10480(ALL)06/95]
P
[IP10490(ALL)06/95]
Push this button for airflow to the floor and windshield at the
same time. ThePindicator light illuminates, and the display
window shows the set temperature. However, the air is not
cooled regardless of the temperature setting unless the A/C
button is pushed.
[IP10500(ALL)06/95]
V
[IP10510(ALL)06/95]
Press this button to obtain maximum airflow to the windshield.
Adjust the temperature setting as required for defrosting. The
Vindicator light illuminates and the display window shows
the set temperature. When the outside temperature is about50ÊF
(10ÊC) the air conditioningfunctions in order to dehumidify the
air to prevent window fogging.
[IP10520(ALL)06/95]
Q
[IP10530(ALL)06/95]
Push this button to select airflow through the instrument panel
registers. TheQindicator light illuminates and the display
window shows the set temperature. The ATC heats the air if the
selected temperature is warmer than the outside air coming into
the vehicle. However, the air is not cooled regardless of the
temperature setting unless the A/C button is pushed.
[IP10540(ALL)06/95]
S
[IP10550(ALL)06/95]
Push this button for air from the floor and instrument panel
registers at the same time. TheSindicator light illuminates
and the display window shows the set temperature. The ATC
heats the air if the selected temperature is warmer than the
outside air coming into the vehicle. However, the air is not
cooled regardless of the temperature setting unless the A/C
button is pushed.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996

108
[IP10560(ALL)06/95]
R
[IP10570(ALL)06/95]
Push this button to direct airflow to the floor. TheRindicator
light illuminates and the display window shows the set
temperature. The ATC heats the air if the selected temperature
is warmer than the outside air coming into the vehicle.
However, the air is not cooled regardless of the temperature
setting unless the A/C button is pushed.
[IP10580(ALL)06/95]
Air Conditioning and Air Recirculation
[IP10590(ALL)06/95]
Activate the air conditioning in any of the function selector
override modes by pressing the A/C button. The A/C indicator
light on the button illuminates to verify activation, and cooled
air flows from the vents. Fan speed continues to be controlled
by the ATC unless the fan speed thumbwheel is used to
override the ATC.
[IP10600(ALL)06/95]
Press theMbutton to choose air recirculation. In this mode
the ATC system recirculates the air inside the vehicle rather
than drawing air from outside. Use this mode together with the
air conditioning to rapidly cool the inside of the vehicle or to
dehumidify the air inside the vehicle.
[IP10610(ALL)06/95]
Rear Passenger Compartment Climate Control System
with Front Passenger ATC
[IP10620(ALL)06/95]
If your vehicle is equipped with ATC, the rear passenger
compartment will also have climate controls so that rear seat
occupants can select their own personal climate comfort level.
[IP10630(ALL)06/95]
The rear seat climate control system is controlled from the main
ATC system on the instrument panel. If the front ATC system is
off, the rear system will also be off. Also, if the rear seat climate
control lever is set in OFF, the rear climate controls are turned
off.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996

110
*
[IP10740(ALL)06/95]
Liftgate Window Features
[IP10750(ALL)06/95]
Rear Window Defogger (If equipped)
*
[IP10760(ALL)06/95]
The defogger for the rear liftgate window clears frost, fog, or
thin ice from both the inside and outside of the rear window.
The defogger operates with the ignition in the ON position.
[IP10770(ALL)06/95]
If your vehicle is equipped with heated exterior mirrors, they
activate when the rear window defogger is switched on.
*
[IP10780(ALL)06/95]
The control switch is located on the instrument panel to the
right of the steering column.
[IP10790(ALL)06/95]
13-1/2 pica
art:0040073-E
Rear window defogger switch location
*
[IP10800(ALL)06/95]
Clear away any snow that is on the rear window and outside
rearview mirrors before using the defroster. With the engine
running, push the defroster button.
*
[IP10810(ALL)06/95]
After approximately 10 minutes, the defroster will turn off. If
the window or mirrors are still not clear, turn the defroster on
again.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996