1996 LINCOLN CONTINENTAL light

If the autolamp is active, the headlamp system
will come on immediately after starting your
vehicle. If your vehicle is running before you
activate the autolamp, there may be a 15 second
delay before the headlights illuminate.
2.Turn the ignition key to ON or start your
vehicle.
3.Find the autolamp switch to the left of the
steering wheel on the instrument panel.
4. Push the autolamp switch up toward the
MAX position. As you press this switch, the
autolamp system's status will be displayed in
the message center. The system can be
turned OFF or can be set to provide light for
up to three (3) minutes after you turn your
vehicle off.
84Do not put any articles on top of the photocell
that is located in the top left corner of the
instrument panel. This photocell controls the
autolamp. If you cover it, the photocell reacts
as if it is nighttime, and the lamps turn on.
To turn the autolamp off, push the switch down
until the message center display reaches OFF.
Turning On Interior
Lights/Instrument Panel Illumination
You can brighten or dim the lights in the
instrument panel and the compass display
in the inside rearview mirror (if
equipped) with the PANEL DIM switch
located on the instrument panel.

Panel dim switch
The switch that controls interior lamps and
instrument panel brightness
To turn on the interior lights, hold the Panel Dim
switch up until the interior lights turn on. To
turn off the interior lights, push the Panel Dim
switch down. The interior lights also come on
when any door is opened or if either front door
outside handle is lifted with the door locked.Turning On the Map Lamps
Your vehicle has a map lamp for the passenger and
one for the driver.TTThe map lamps on vehicles equipped with a
moon roof
85

Map lamp Dome lamp ON/OFF Switches
The map lamps on the inside roof of the car
To turn on the map lamps, push the switches in
front of each lamp.
On vehicles equipped with the moon roof
Option, the map lamps and switches are located
on the inside rearview mirror.
86Rear Courtesy/Reading Lamps
Your vehicle has two rear passenger
courtesy/reading lamps.
The courtesy lamp lights when any door is
opened or when the instrument panel
dimmer switch is turned to the courtesy
lamp position or if either front door outside
handle is lifted with the door locked.
With the ignition key in the ACC or ON
position, the reading lamp can be turned on
by using the rocker switch on the lamp
assembly.

Steering Column ControlsThe controls on the steering column and wheel
are designed to give you easy access to the
controls while you are driving.
The Turn Signal Lever
You can use the turn signal lever on the left side
of the steering column to: operate the turn signals and cornering lamps turn the high beams on/off flash the lights turn the windshield wipers and washer on/offThe turn signal lever
Turn Signals
Move the lever up to signal a right turn. Move it
down to signal a left turn. The corresponding
indicator light in the instrument cluster will flash.
89

If the turn signal stays on after you turn, move
the lever back to the center (off) position. A
warning chime will sound after approximately
one-half mile (one kilometer) of driving if you do
not return the lever to off.
For lane changes, move the lever far enough to
signal but not to latch. The lever will return to
the off position when you release it.
NOTE: The flash rate of the turn signal will
speed up considerably if the Lighting Control
Module detects a left or right turn lamp bulb
(front or rear) is burned out.
High Beams
To turn on the high beams, turn the headlamp
control switch to the headlamp ON position (or
activate the autolamp feature) and push the turn
signal lever away from you until it latches. When
the high beams are ON, the high beam indicator
light on the instrument cluster comes on.
90To turn off the high beams, pull the lever toward
you until it latches. The high beam indicator
light turns off.
Flashing the Lights
To flash the headlamps, pull the lever toward
you for a moment and then release it. The
headlamps will flash whether the headlamp knob
is in the on or off position.
Windshield Wipers and Washer
To turn on the windshield wipers, the ignition
key must be turned to the ON or ACC position.
Rotate the knob towards "S" to activate the
wipers. The first seven detents are interval wipe
positions, the eighth detent is the LO position
and the ninth detent is the HI position.
To turn the wipers off, turn the knob to the OFF
position.

NOTE: If your speed increases above your set
speed while driving in (Overdrive) on a
downhill grade, you may want to shift to D
(Drive) to reduce vehicle speed. The speed
control cannot reduce the vehicle speed if it goes
above your set speed on a downhill grade. For
the best fuel economy during normal driving
conditions, leave the shift select in (Overdrive), or resume as soon as practical./! WARNINGDo not use the speed control in heavytraffic or on roads that are winding,slippery, or unpaved.Accelerating With the Speed Control
Operating
You can use the accelerator pedal to speed up
momentarily. When you take your foot off the
accelerator, the vehicle will return to the set
speed.Resetting the Speed Control
To reset the speed control to a lower speed, use
one of the following procedures: COAST - Press and hold the COAST switch.
Release the switch when the vehicle slows down
to the desired speed. Lightly tap the brake pedal. When the vehicle
attains the desired speed, press the SET
ACCEL switch and release it immediately. TAP-DOWN - Press and release the COAST
switch momentarily for each m.p.h. (1.6 km/h)
reduction in speed desired.
If vehicle speed is reduced below 30 mph (50
km/h) by any of the above methods, then you must
manually accelerate to a speed over 30 mph (50
km/h) and reset the system.
97

To reset the speed control to a higher speed,
follow one of these procedures: ACCEL - Press and hold the SET ACCEL
switch. Release the switch when the vehicle
has accelerated to the desired speed. Depress the accelerator pedal. When the
vehicle attains the desired speed, press the
SET ACCEL switch and release it
immediately. TAP-UP - Press and release the SET ACCEL
switch momentarily for each m.p.h. (1.6 km/h)
increase in speed desired.
To Cancel Speed Control
Speed control can be cancelled at any time by
pressing the brake pedal slightly. After
cancelling, you can return to the speed you set by
pressing the RES switch, or set a new speed by
pressing the SET ACCEL or COAST switches.
98To Turn Speed Control Off
Press the OFF switch.
Speed control is also turned OFF each time the
vehicle ignition is shut off.
Cancelling and Resuming a Set Speed
If you press the brake pedal, speed control is
suspended. You can return to the set speed by
pressing the RES switch, as long as you did not
press the OFF switch. You must be driving at least
30 mph (48 km/h).
Your vehicle will gradually return to the previously
set speed and then maintain it.

Illuminated Entry System with Theater
Lighting
The interior lights will illuminate for approximately
25 seconds when either front door handle is lifted,
any button on the keyless entry pad is pressed, or
the remote entry system UNLOCK button is
pushed. If the amount of light outside your vehicle
is below a predetermined level, the exterior lights
will also illuminate.
Using the Keyless Entry System
You can lock or unlock the vehicle doors and open
the trunk without using a key. The buttons for the
system are below the outside door handle on the
driver's side. See also Remote Entry System which
follows this description.The keyless entry buttons
When you bought your vehicle, you were given a
computer code that operates the system for your
vehicle. For your convenience, we have
duplicated this code in three places.
The code is: on your owner's wallet card found in the glove
compartment
101