1996 LAND ROVER DEFENDER oil

19FUEL SYSTEM
14
REPAIR TURBOCHARGER INLET HOSE
Service repair no - 19.42.11
Remove
1.Disconnect battery.
2.Slacken retaining clip and disconnect intake
hose from turbocharger.
3.Slacken retaining clip and disconnect hose from
air cleaner.
4.If fitted, disconnect EGR modulator valve
vacuum spill pipe from inlet hose.
5.Slacken retaining clip and disconnect breather
valve hose from inlet hose.
6.Remove inlet hose.
Refit
7.Fit inlet hose to air cleaner.
8.Fit cyclone breather hose to inlet hose.
9.If applicable, fit vacuum spill pipe to inlet hose.
10.Fit inlet hose to turbocharger.
11.Reconnect battery.TURBOCHARGER OIL FEED PIPE
Service repair no - 19.42.14
Remove
1.Disconnect battery.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
front pipe
3.Remove banjo bolt securing oil feed pipe to
turbocharger and discard 2 joint sealing
washers.
4.Unscrew union and remove feed pipe from
cylinder block.
5.Plug connections to prevent ingress of dirt.
Refit
6.Using new joint washer, fit oil feed pipe to
cylinder block. Tighten union connector to
25
Nm (18 lbf/ft).
7.Fit a new joint washer to both sides of banjo and
secure feed pipe to turbocharger. Tighten banjo
bolt to
20 Nm (15 lbf/ft).
8.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust front
pipe
9.Check/top-up engine oil level.See SECTION
10, Maintenance, Under bonnet maintenance
10.Reconnect battery.

FUEL SYSTEM
15
REPAIR TURBOCHARGER OIL DRAIN PIPE
Service repair no - 19.42.12
Remove
1.Disconnect battery.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
front pipe
3.Unscrew union and disconnect oil drain pipe
from cylinder block.
4.Remove 2 bolts securing oil drain pipe to
turbocharger.
5.Remove drain pipe and discard gasket.
6.Plug connections to prevent ingress of dirt.
Refit
7.Ensure mating surfaces of oil pipe, turbocharger
and engine block are clean.
8.Using new gasket, fit oil drain pipe to
turbocharger. Tighten bolts to
25 Nm (18 lbf/ft).
9.Fit drain pipe to cylinder block and tighten union
connector to
38 Nm (28 lbf/ft).
10.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust front
pipe
11.Check/top-up engine oil level.See SECTION
10, Maintenance, Under bonnet maintenance
12.Reconnect battery.

COOLING SYSTEM
1
DESCRIPTION AND OPERATION ENGINE COOLING SYSTEM
Description
The complete cooling system of the 300Tdi engine
incorporates three independent functions:- Engine
(coolant) cooling; Turbo (charge air) intercooling;
Engine oil cooling.The intercooler is a separate aluminium unit, located
on the LH side of the engine compartment adjacent to
the radiator, sharing the same upper and lower
mountings. For details of turbo intercooling
See
FUEL SYSTEM, Description and operation,
Operation
. The oil cooler matrix is an integral part of
the radiator. Pre-formed pipes/hoses are used to link
the components within the separate systems as
shown below.
Engine cooling system
1.Radiator
2.Thermostat housing
3.Radiator bottom hose
4.Viscous fan
5.Water pump
6.Radiator top hose
7.Heater return hose
8.Coolant supply hose
9.By-pass hose
10.Radiator bleed (purge) hose
11.Bleed (purge) hose, thermostat housing
12.'Y' piece ejector
13.Expansion tank14.Heater rail
15.Heater unit
16.Heater feed hose
17.Intercooler
18.Air cleaner
19.Air feed hose
20.Turbocharger
21.Charge air supply pipe/hose
22.Cooled charge air supply hose
23.Exhaust manifold
24.Engine oil cooler
25.Feed pipe, engine oil cooler
26.Return pipe, engine oil cooler
27.Oil filter

COOLING SYSTEM
3
DESCRIPTION AND OPERATION COOLANT CIRCULATION
Operation
When the engine is started from cold the thermostat
(2) prevents coolant circulation through the radiator by
closing off the top hose (6). During the engine warm
up period the water pump (5) circulates coolant to the
cylinders in the crankcase and through separate ports
to the cylinder head. At the rear of the cylinder head a
proportion of the flow is diverted through a heater feed
pipe (16) to the matrix of the heater unit (15). The
coolant is then carried, via a heater return rail (14) and
hoses (7), back to the water pump. The remaining
coolant flows through a by-pass hose (9) at the
thermostat housing and back to the water pump to
complete the first cycle.
When the normal engine running temperature is
reached, the thermostat opens, closing off the by-pass
hose (9). Coolant is then circulated via the top hose
(6) and through the radiator, where it is cooled and
drawn from the radiator bottom hose (3) by the water
pump (5). The coolant circulation through the
crankcase and cylinder head remains the same.
Two bleed pipes (10) and (11) help control the system
pressure by purging excess air and coolant to the
expansion tank via the 'Y'piece ejector (12).VISCOUS FAN
Description
The viscous drive unit for the engine cooling fan,
provides a means of controlling the speed of the fan
relative to the running temperature of the engine. The
viscous unit is a type of fluid coupling, which drives
the fan blades by means of 'silicone fluid'.
1.Input (drive) member
2.Output (driven) member
3.Sensing mechanism (bi-metal coil)
The fan drive has to be engaged only periodically,
between 5% and 10%, during normal operating
conditions, because the engine is cooled by ram air
for most of the time.

26COOLING SYSTEM
4
DESCRIPTION AND OPERATION Operation
To engage and disengage the fan drive the bi-metal
coil senses air temperature behind the radiator. When
a pre-determined temperature is reached, the coil
opens a valve (5) which allows fluid to enter the drive
area and, due to centrifugal force, circulates to the
annular drive area.
There are two sets of annular grooves (3), one in the
drive clutch and the other in the drive body, a specific
clearance being provided between the two sets of
grooves.
Viscous unit disengaged (engine at normal
running temperature)
1.Input (drive) member
2.Output (driven) member
3.Running clearance
4.Pump plate
5.Valve (closed)
6.Sensing mechanism (bi-metal coil)
7.Fluid seal
8.Bearing, input member
9.Fluid chamber
10.Fluid reservoirWhen this clearance is filled with viscous fluid, a
shearing action, caused by the speed differential
between the two drive components, transmits torque
to the fan. The fluid is thrown to the outside of the unit
by centrifugal force from where it is recirculated to the
reservoir (10) via the pump plate (4) adjacent to the
drive member.
If the engine speed is increased the amount of slip will
also increase to limit the maximum fan speed.
When the air temperature from the radiator drops
sufficiently, the bi-metal coil closes the valve and
prevents fluid entering the drive area. The fluid that is
in the drive area will gradually pump out into the
reservoir (10) and the fan will return to an idle
condition.
Viscous unit engaged (hot running temperature)
Bi-metal coil (6) expanded, valve (5) open.

COOLING SYSTEM
3
REPAIR WATER PUMP
Service repair no - 26.50.01
Remove
1.Disconnect battery.
2.Drain cooling system.
See Adjustment, Drain
and refill cooling system
3.Remove radiator top hose.
4.Remove intercooler top hose.
5.Slacken water pump and power steering pump
pulley retaining bolts.
6.Remove drive belt.
See ELECTRICAL, Repair,
Auxiliary drive belt
7.Unscrew flange nut and remove belt tensioner.
8.Remove oil filler cap and remove rocker cover
insulation.
9.Slacken retaining clip and disconnect hose at
heater rail.
10.Unscrew 3 bolts and remove water pump pulley.
11.Unscrew 3 bolts and remove power steering
pump pulley.
12.Remove 8 bolts securing water pump, noting
location of 3 through bolts into cylinder block.
13.Withdraw pump and gasket from auxiliary
mounting bracket.
14.Clean all gasket material from mating faces.
Refit
15.Using new gasket, fit water pump to mounting
bracket. Tighten bolts to
25 Nm (18 lbf/ft).
16.Fit power steering pump pulley.
17.Fit water pump pulley. Tighten bolts of both
pulleys to
25 Nm (18 lbf/ft).
18.Fit drive belt.See ELECTRICAL, Repair,
Auxiliary drive belt
19.Fit hose at heater rail.
20.Fit rocker cover insulation and oil filler cap.
21.Fit drive belt tensioner. Tighten retaining nut to
45 Nm (33 lbf/ft).
22.Fit intercooler top hose.
23.Fit radiator top hose.
24.Refill cooling system.
See Adjustment, Drain
and refill cooling system
25.Reconnect battery.

26COOLING SYSTEM
6
REPAIR RADIATOR
Service repair no - 26.40.01
Remove
1.Disconnect radiator bottom hose and drain
cooling system.
See Adjustment, Drain and
refill cooling system
2.Disconnect radiator top hose.
3.Remove viscous fan unit.
See Viscous
coupling and fan
4.Remove fan cowl.See Fan cowl
5.Disconnect oil cooler pipes. Plug all connections
to prevent oil spillage and ingress of dirt.
6.Disconnect top and bottom intercooler hoses.
7.Disconnect bleed hose at radiator.
8.Remove 2 bolts from both sides securing
radiator mounting brackets to bonnet platform.
9.Lift and remove radiator/intercooler assembly
from vehicle.
10.Remove 2 bolts from both sides and detach
radiator top cover from side covers.
11.Lift and remove radiator from intercooler and RH
side frame.
12.Check condition of locating grommets in radiator
top cover and lower mounting bushes. Renew if
necessary.Refit
13.Position radiator between intercooler and RH
side frame.
14.Fit radiator top cover to side covers.
15.Lower radiator/intercooler assembly into
position.
16.Secure radiator mounting brackets to bonnet
platform.
17.Fit radiator bleed hose.
18.Fit top and bottom intercooler hoses.
19.Fit oil cooler pipes.
20.Fit fan cowl
See Fan cowl.
21.Fit viscous fan unit.
See Viscous coupling
and fan
22.Fit radiator top hose.
23.Fit radiator bottom hose and refill cooling
system.
See Adjustment, Drain and refill
cooling system

MANIFOLD AND EXHAUST SYSTEM
1
REPAIR INDUCTION MANIFOLD
Service repair no - 30.15.02
Remove
1.Disconnect battery.
2.Remove oil filler cap and remove rocker cover
insulation.
3.Remove hose intercooler to induction manifold. If
fitted, remove EGR valve.
See FUEL SYSTEM,
Repair, EGR valve
4.Remove 2 screws and release heat shield from
induction manifold.
5.Slacken induction manifold lower securing nuts,
located below exhaust manifold.
6.Remove induction manifold upper securing bolts.
7.Remove induction manifold. Plug apertures in
cylinder head with clean rag to prevent any items
falling into engine.
8.Check gasket is satisfactory for further use.
Refit
9.Clean induction manifold mating face.
10.Position induction manifold and secure with
upper and lower fixings.
11.Tighten securing nuts and bolts to
25 Nm (18
lbf/ft).
12.Fit manifold heat shield.
13.Fit hose intercooler to induction manifold.
14.Fit rocker cover insulation.
15.Reconnect battery.INDUCTION/EXHAUST MANIFOLD GASKET
Service repair no - 30.15.15
Remove
1.Remove induction manifold
See Induction
manifold
.
2.Remove turbocharger outlet hose.
3.Raise vehicle and slacken exhaust front pipe to
intermediate silencer flange nuts. Ensure pipe is
free to turn.
NOTE: If removing exhaust manifold and
turbocharger assembly from vehicle,
remove manifold to exhaust front pipe
nuts while working under vehicle.
4.Remove exhaust manifold securing nuts,
removing centre lower nut first.
5.Move heater rail clear of exhaust manifold.
6.With exhaust manifold and turbocharger still
attached to exhaust front pipe, withdraw from
head by turning front pipe until sufficient access
is gained to remove gasket.
7.Suitably support exhaust manifold and
turbocharger assembly to prevent damage.
8.Remove induction manifold lower nuts.
9.Remove gasket.
10.Clean mating faces.