1996 LAND ROVER DEFENDER oil

ENGINE
11
REPAIR CRANKSHAFT OIL SEAL
Service repair no - 12.21.14
Remove
1.Remove crankshaft gear.
See Crankshaft gear
2.Prise out oil seal from front cover.
Refit
3.Lubricate a new crankshaft oil seal with clean
engine oil.
4.With lip side leading, drive in seal squarely using
special toolLRT-12-079.
5.Fit crankshaft gear.
See Crankshaft gear
CAMSHAFT GEAR
Service repair no - 12.65.24
Remove
1.Remove camshaft drive belt.
See Camshaft
drive belt
2.Remove centre bolt and withdraw camshaft
gear, complete with hub and retaining plate.
Refit
3.Fit camshaft gear. Tighten bolt to
80 Nm (59
lbf/ft).
4.Fit camshaft drive belt.See Camshaft drive
belt

12ENGINE
12
REPAIR CAMSHAFT OIL SEAL
Service repair no - 12.13.05
Remove
1.Remove camshaft gear.
See Camshaft gear
2.Remove camshaft oil seal from front cover using
special toolLRT-12-083.
Refit
3.Lubricate a new camshaft oil seal with clean
engine oil.
4.With lip side leading, drive in seal squarely using
special toolLRT-12-082.
5.Fit camshaft gear.
See Camshaft gear
INJECTION PUMP GEAR
Service repair no - 19.30.06
Remove
1.Remove camshaft drive belt.
See Camshaft
drive belt
2.Slacken 3 bolts on front of injector pump gear.
3.Remove special tool pin from gear.
4.Remove 3 bolts and withdraw gear and retaining
plate.
Refit
CAUTION: It is important to ensure that
when the injection pump is locked no
attempt must be made to rotate it. Take
care not to allow the crankshaft to be turned.
5.Fit gear and retaining plate. Tighten bolts to
25
Nm (18 lbf/ft).
6.Insert pin from special toolLRT-12-045in
injection pump gear and through into pump
flange.
7.Fit camshaft drive belt.
See Camshaft drive
belt

ENGINE
13
REPAIR FRONT COVER GASKET
Service repair no - 12.65.10
Remove
1.Remove camshaft drive belt.
See Camshaft
drive belt
2.Remove crankshaft gear.See Crankshaft gear
3.Remove camshaft gear.See Camshaft gear
4.Remove injection pump gear.See Injection
pump gear
5.Remove fuel injection pump.See FUEL
SYSTEM, Repair, Fuel injection pump
6.Remove engine oil sump.See Engine oil
sump
7.Remove oil pick up strainer.See Oil pick-up
strainer
8.Remove 10 bolts securing timing gear housing to
block.
9.Withdraw timing gear housing complete with
gasket.
10.Clean all gasket material from mating faces.
Refit
11.Fit slave guide studs to locate gasket.
12.Fit new gasket to cylinder block.
13.Align flats on oil pump with flats on crankshaft.
14.Fit front cover to block taking care not to damage
oil seal.15.Secure with bolts of correct length in locations
where slave studs are not fitted, see J6149.
16.Remove slave studs and fit correct length bolts.
17.Tighten all bolts to
25 Nm (18 lbf/ft).
1- 25 mm,2- 35 mm,3- 80 mm.
18.Fit oil pick-up strainer.
See Oil pick-up
strainer
19.Fit oil sump.See Engine oil sump
20.Fit fuel injection pump.See FUEL SYSTEM,
Repair, Fuel injection pump
21.Fit injection pump gear.See Injection pump
gear
22.Fit camshaft gear.See Camshaft gear
23.Fit crankshaft gear.See Crankshaft gear
24.Fit camshaft drive belt.See Camshaft drive
belt

12ENGINE
14
REPAIR ENGINE OIL SUMP
Service repair no - 12.60.44
Remove
1.Disconnect battery.
2.Drain engine oil.
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
remove and refit procedures are required, it may
be necessary to remove the undertray and/or
integral access panels.
See CHASSIS AND BODY, Repair, Front
undertray
orSee CHASSIS AND BODY, Repair,
Rear undertray
3.Slacken sump securing bolts.
4.Break sealant around sump flange, using a
sharp knife.
5.Remove 22 bolts and withdraw sump.
Refit
6.Clean mating faces of sump, timing gear housing
and cylinder block.
7.Apply a 2,0 mm bead of 'Hylosil RTV102' to the
sump flange, ensuring bead is applied inboard of
the bolt holes.
8.Secure sump to block with 22bolts. Tighten to
25
Nm (18 lbf/ft).
9.Refill engine oil.See LUBRICANTS, FLUIDS
AND CAPACITIES, Information, Capacities
10.Reconnect battery.OIL PICK-UP STRAINER
Service repair no - 12.60.20
Remove
1.Disconnect battery.
2.Drain engine oil.
3.Remove engine oil sump.
See Engine oil
sump
4.Remove 2 bolts securing pipe support bracket to
main bearing cap fixings.
5.Remove bolts from pipe flanges.
6.Withdraw pick-up strainer assembly.
Refit
7.Postion pick-up strainer assembly, fitting a new
'O' ring seal at oil pump connection.
8.Apply Loctite 242E to threads of bolts at main
bearing cap. Fit bolts, tighten to
9 Nm (7 lbf/ft).
9.Fit bolts to pipe flanges. Tighten to25 Nm (18
lbf/ft).
10.Fit sump.See Engine oil sump
11.Reconnect battery.

12ENGINE
16
REPAIR CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
Remove
NOTE: The crankshaft rear oil seal is
retained in its own housing, if the seal
requires replacing, the complete housing
assembly (1) must be renewed. Housing and seal
assemblies are supplied with their own
former/seal guide (2) already fitted. This former
must not be removed before fitting the assembly
to the engine. If a seal and housing assembly is
received without a former/guide fitted it must be
returned to the supplier. Used formers/guides
must be discarded immediately after use, under
no circumstances should they be reused on other
assemblies.
NOTE: A different rear oil seal housing,
with integral 'O' ring seal and gasket, was
fitted on earlier engines. They must be
replaced with the current housing and gasket (3)
shown below.
1.Disconnect battery.
2.Remove gearbox.
See MANUAL GEARBOX,
Repair, R380 gearbox
3.Remove clutch.See CLUTCH, Repair, Clutch
assembly
4.Remove flywheel.See Flywheel
5.Remove 5 bolts and withdraw seal housing,
complete with gasket.
Refit
NOTE: The raised side of groove at the
bottom of seal housing gasket must be
fitted to cylinder block face.
6.Insert slave studs to locate seal housing gasket.
7.Position new gasket over slave studs and
crankshaft flange onto cylinder block.
8.Fit new seal housing assembly, with
former/guide in-situ, over crankshaft flange. This
action will eject former/guide.
9.Secure assembly to cylinder block, removing
slave studs individually and inserting bolts.
Tighten to
25 Nm (18 lbf/ft).
10.Refit flywheel.See Flywheel

ENGINE
19
REPAIR OIL FILTER
Service repair no - 12.60.01
Remove
1.Place drain tray under oil filter.
2.Unscrew filter anti-clockwise, using a strap
wrench, if necessary.
Refit
3.Clean mating face of oil filter adaptor.
4.Coat rubber sealing ring of new filter with clean
engine oil.
5.Screw on filter until sealing ring touches
machined face, then tighten a further half turn by
hand only. DO NOT over tighten.OIL TEMPERATURE CONTROL VALVE
Service repair no - 12.60.69
Remove
1.Clean adaptor housing.
2.Disconnect oil cooler feed pipe from thermostat
extension housing and plug to prevent ingress of
dirt.
3.Remove 2 bolts and carefully withdraw
thermostat extension housing (1) complete with
'O' ring seal (2), thermostat (3), 2 washers (4)
and spring (5).
4.Inspect all parts and renew as necessary.
Refit
5.Fit thermostat to extension housing ensuring pin
locates in hole.
6.Fit two washers and spring to thermostat.
7.Fit a new 'O' ring to extension housing.
8.Insert spring into adaptor and secure extension
housing to adaptor. Tighten bolts to
9Nm(7
lbf/ft).

12ENGINE
20
REPAIR OIL FILTER HEAD GASKET
Service repair no - 12.60.03
Remove
1.Clean filter head adaptor.
2.Disconnect oil cooler pipes and plug to prevent
ingress of dirt.
3.Disconnect oil pressure switch lead.
4.Remove 4 bolts and withdraw filter head,
complete with gasket.
5.Clean mating faces of filter head and cylinder
block.
6.Fit head with new gasket.
7.Tighten bolts to
45 Nm (33 lbf/ft).
8.Reconnect oil pressure switch lead.
9.Reconnect oil cooler pipes.CYLINDER HEAD GASKET
Service repair no - 12.29.02
Remove
1.Disconnect battery
2.Remove bonnet.
3.Drain coolant.
See COOLING SYSTEM,
Repair, Drain and refill cooling system
4.Remove air cleaner.See FUEL SYSTEM,
Repair, Air cleaner
5.Detach crankcase ventilation valve and side
breather hose from rocker cover and move to
one side.
6.Remove fuel injectors and pipes.
See FUEL
SYSTEM, Repair, Fuel injectors
7.Remove heater plugs.See FUEL SYSTEM,
Repair, Heater plugs
8.Disconnect radiator top hose from thermostat.
9.Disconnect bleed hose at thermostat.
10.Disconnect water pump hose at thermostat.
11.Disconnect water temperature sensor lead.

12ENGINE
22
REPAIR
28.Lower cylinder head onto block ensuring correct
location with dowels.
NOTE: Cylinder head retaining bolts can
be used up to a maximum of five times.
29.Lubricate threads of bolts with light oil and fit to
positions shown below. (Fit air cleaner mounting
bracket at positions 6 and 14).
Bolt sizes:
M10 x 117mm locations 3, 5, 12, and 13.
M12 x 140mm locations 1, 2, 7, 8, 9, 10, 15, 16, 17,
and 18.
M12 x 100mm locations 4, 6, 11, 14.
30.Tighten bolts so that underside of heads just
make contact with cylinder head.
31.Following the sequence indicated, tighten all
bolts to
40 Nm (30 lbf/ft).
32.Attach angle gaugeLRT-12-007.
33.Make a suitable pointer from welding rod and
attach to a bolt screwed into a rocker shaft
securing bolt hole.
34.Tighten all bolts through 60°strictly in sequence
illustrated.
35.Repeat 60°tightening procedure, again strictly in
sequence illustrated.
36.Tighten the 10 longer bolts (M12 x 140mm) a
further 20°, again following the sequence
illustrated.
NOTE: Repositioning of the pointer will be
necessary to reach all bolts, the pointer
can be fitted to the rocker shaft securing
studs using 2 nuts.
CAUTION: The double tightening
procedure MUST be carried out, on no
account should the bolt tightening be
performed in one operation, otherwise damage to
the cylinder head may occur.
37.Fit valve stem caps.
38.Fit push rods to locations from which they were
removed.
39.Position rocker shaft assembly over locating
studs and fit retaining nuts and bolts, but do not
tighten at this stage.
40.Attach angle gaugeLRT-12-007.
41.Make a suitable pointer and attach to one of the
rocker shaft locating studs.
42.Tighten all fixings in turn to
5 Nm (4 lbf/ft).Then
tighten a further 50°in same sequence.
NOTE: Repositioning of the pointer will be
necessary to reach all fixings.