1996 LAND ROVER DEFENDER drain bolt

57STEERING
6
REPAIR POWER STEERING SYSTEM - BLEED
Service repair no - 57.15.02
1.Check that fluid level is at maximum level
See
MAINTENANCE , Under bonnet maintenance.
2.Run engine to normal operating temperature.
3.Recheck reservoir fluid level, top up if necessary
NOTE: During operations 4 to 6, maintain
maximum fluid level in reservoir. Do not
increase engine speed or move steering
wheel.
4.With engine at idle speed, slacken bleed screw.
When fluid seeps past bleed screw retighten
screw.
5.Check fluid level.
6.Clean away fluid around bleed screw.
7.Check hose connections, pump and steering box
for fluid leaks by holding steering on full lock in
both directions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute to avoid overheating fluid and
possibly damaging seals.
8.Carry out road test.POWER STEERING FLUID RESERVOIR
Service repair no - 57.15.08
Remove
1.Position drain tin beneath reservoir.
2.Slacken mounting bracket clamp bolt and raise
reservoir to gain access to feed and return hose
retaining clips.
3.Slacken clips, disconnect hoses from reservoir,
allow fluid to drain.
4.Remove reservoir.
CAUTION: Plug connections to prevent
ingress of dirt.
CAUTION: Discard fluid drained from
system. Do not allow fluid to contact
paintwork, if spilled, remove fluid and
clean area with warm water.
Refit
5.Position reservoir, connect feed and return
hoses and tighten clips to
3 Nm (2 lbf/ft).
6.Fit reservoir in clamp, tighten clamp bolt.
7.Fill reservoir between upper mark and end of
dipstick with power steering fluid
See
MAINTENANCE , Under bonnet maintenance
.
8.Bleed power steering system
See Power
steering system - bleed
.

STEERING
7
REPAIR POWER STEERING PUMP
Service repair no - 57.20.14
Remove
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
remove and refit procedures are required, it may
be necessary to remove the undertray
See
CHASSIS AND BODY, Repair, Front undertray
.
1.Disconnect battery.
2.Remove viscous fan unit
See COOLING
SYSTEM, Repair, Viscous coupling and fan
.
3.Restrain steering pump pulley, slacken but do
not remove 3 bolts securing pulley.
4.Remove drive belt
See ELECTRICAL, Repair,
Auxiliary drive belt
.
5.Remove bolts and remove pulley.
6.Position suitable container beneath steering
pump.
7.Slacken retaining clip and disconnect return
hose from steering pump.
8.Disconnect high pressure pipe from steering
pump.
9.Allow steering fluid to drain into container.
CAUTION: Plug all connections to prevent
ingress of dirt.
10.Remove 4 bolts securing steering pump bracket
to engine auxiliary mounting bracket.
11.Remove pump and bracket assembly.
12.Remove 3 bolts and detach mounting bracket
from pump.
Refit
13.Fit mounting bracket to replacement steering
pump. Tighten bolts to
9 Nm (7 lbf/ft).
14.Fit pump and bracket to auxiliary mounting
bracket. Tighten bolts to
35 Nm (26 lbf/ft).
15.Connect high pressure feed pipe to steering
pump and tighten to
20 Nm (15 lbf/ft).
16.Connect return hose to steering pump. Tighten
retaining clip to
3 Nm (2 lbf/ft).
17.Position pulley to steering pump, coat threads of
bolts with Loctite 242; fit but do not fully tighten
bolts.
18.Fit drive belt
See ELECTRICAL, Repair,
Auxiliary drive belt
.
19.Restrain steering pump pulley, tighten bolts to
10
Nm (7lbf/ft).
20.Fit viscous fan unitSee COOLING SYSTEM,
Repair, Viscous coupling and fan
.
21.Bleed power steering system
See Power
steering system - bleed
.
POWER STEERING PUMP DRIVE BELT
Service repair no - 57.20.02
NOTE: For details of drive belt remove and
refit
See ELECTRICAL, Repair, Auxiliary
drive belt
.

STEERING
1
OVERHAUL POWER STEERING BOX - ADWEST
Service repair no - 57.10.07
Overhaul
NOTE: Overhaul of steering box should
not be carried out during the warranty
period.
WARNING: Wear safety glasses while
removing and refitting circlips and
retaining ring.
CAUTION: Absolute cleanliness is
essential when overhauling power steering
box.
1.Remove steering box from vehicleSee Repair,
Power Steering Box
. Mark drop arm and
steering box for realignment on assembly.
Remove drop arm using extractorLRT-57-012.
Loosen drop arm securing nut, but do not
remove before using extractor. Remove dirt
excluder from output shaft.
2.Drain oil, remove blanking plugs and bleed
screw. Hold steering box over suitable container,
turn input shaft from lock to lock, until oil is
drained. Refit bleed screw.
3.Rotate retainer ring until one end is 12 mm from
extractor hole. Using a drift through hole in
cylinder, lift retaining ring from groove in cylinder
bore.
4.Remove retainer ring, using a screwdriver.
5.Turn input shaft (left lock on left hand drive, right
lock on right hand drive) until piston pushes out
cover. Turn input shaft fully in opposite direction,
applying pressure to piston.
6.Remove set screw retaining rack pad adjuster.
7.Remove rack adjuster and pad.
8.Remove sector shaft adjuster locknut.
9.Remove four bolts from sector shaft cover.
10.Screw in sector shaft adjuster until cover is
removed.
NOTE: Sealant is applied to hexagon
socket to 'tamperproof' sector shaft
adjuster.
11.Slide out sector shaft.

CHASSIS AND BODY
39
REPAIR ACCESS PANEL - FRONT UNDERTRAY
Service repair no - 76.11.85 - Access panel
Service repair no - 76.11.83 - Acoustic pad
The access panel is provided in the front undertray to
enable fitment of the wading plug into the engine
timing cover.
Remove
1.Raise vehicle on ramp.
2.Remove 5 bolts securing access panel to front
undertray.
3.Remove access panel.
4.If necessary, remove 5 fasteners and release
acoustic pad from access panel.
Refit
5.If applicable, fit acoustic pad to access panel.
6.Fit access panel to front undertray, Tighten
fixings to
14 Nm (10 lbf/ft).
7.Lower ramp.ACCESS PANEL - REAR UNDERTRAY
Service repair no - 76.11.84
The access panel is provided in the rear undertray to
enable fitment of the wading plug or timing tool
LRT-12-044in the flywheel housing, and access to
the engine oil sump drain plug.
Remove
1.Raise vehicle on ramp.
2.Rotate access panel anti-clockwise to release
locking flanges.
3.Remove access panel from undertray.
Refit
4.Locate access panel flanges in undertray
apertures.
5.Rotate panel clockwise to secure in undertray.
6.Lower ramp.

HEATING AND VENTILATION
1
REPAIR HEATER UNIT
Service repair no - 80.20.01
Remove
1.Remove bonnet and disconnect battery.
2.Remove radiator bottom hose at radiator union
and drain cooling system
See COOLING
SYSTEM, Repair, Drain and refill cooling
system
.
3.Slacken clips and remove heater hoses at
heater box unions.
4.Remove outer cable securing clips.
5.Slacken trunnions and remove control cables
from heater vent flap levers.
6.Remove heater wiring harness securing loop.
7.Disconnect harness multi-plug.
8.Remove interior bulkhead trim.
9.Remove lower nuts and bolts securing the
heater unit to the bulkhead.
10.Slacken heater unit upper retaining bolts.
11.Manoeuvre heater unit, complete with blower
motor, clear of air inlet duct and remove from
engine compartment.
12.If existing heater unit is to be refitted, remove
sealing rubber.
For heater matrix removal
See Heater matrix.
For blower motor removal
See Blower motor.
Refit
13.Smear a new heater unit sealing rubber with a
suitable impact adhesive and fit to heater.
14.Manoevre heater unit into position in engine
compartment, fit blower motor to air inlet duct
and locate upper fixing bolts.
15.Loosely fit heater unit lower fixing bolts.
16.Fully tighten upper fixing bolts.
17.Fully tighten lower fixings and refit interior
bulkhead trim.
18.Secure wiring harness and reconnect multi-plug.
19.Fit control cables to vent flap trunnions and
secure with outer cable clips.
20.Connect heater hoses.
21.Fit radiator bottom hose and refill cooling system
See COOLING SYSTEM, Repair, Drain and
refill cooling system
.
22.Fit bonnet and reconnect battery.