1996 LAND ROVER DEFENDER drain bolt

ENGINE
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine block
Bearing cap 133...............................................................................................
Blanking plug, oil gallery, rear 37....................................................................
Oil squirt jet assembly 17................................................................................
Drain plug, cylinder block 25...........................................................................
Oil squirt jet, vacuum pump cam 7.................................................................
Connecting rod to cap 59................................................................................
Oil pick up assembly to bearing cap 9...........................................................
Oil pick up assembly to front cover 25............................................................
Camshaft thrust plate 9..................................................................................
Oil drain pipe to block (internal) 25.................................................................
Oil drain pipe to block (external) 25................................................................
Sump to cylinder block and front cover 25......................................................
Drain plug, oil sump 35...................................................................................
Tappet guide 14..............................................................................................
Breather side cover assembly 25....................................................................
Baffle plate to breather side cover 4..............................................................
Vacuum pump 25............................................................................................
Fuel lift pump 25.............................................................................................
Flywheel housing 45.......................................................................................
Flywheel housing clutch cover stud 10...........................................................
Plug, flywheel housing 12...............................................................................
Rear oil seal assembly 25...............................................................................
Oil filter adaptor 45..........................................................................................
Waxstat adaptor to oil filter adaptor 9............................................................
Oil pressure switch 17.....................................................................................
Oil filter, spin on 13.........................................................................................
Oil cooler unions to filter adaptor 45...............................................................
Oil level tube 25..............................................................................................
Engine mounting foot to cylinder block 85......................................................
Engine mounting foot to flywheel housing 45.................................................
Engine mounting foot rubber to mounting foot (bolt and nut) 85.....................
Flywheel to crankshaft 146..............................................................................
Clutch cover plate to flywheel 34....................................................................
Flex drive plate to crankshaft (auto) 146..........................................................
Flex drive plate to ring gear (auto) 25.............................................................
Flex drive plate to torque converter (auto) 45.................................................

ENGINE
3
SPECIFICATIONS, TORQUENm
Turbo charger oil drain adaptor to block 42....................................................
Oil drain pipe to turbocharger 25....................................................................
Turbocharger oil drain pipe to adaptor 38.......................................................
Turbocharger oil feed pipe adaptor to block 25...............................................
Turbocharger oil feed pipe to adaptor 25........................................................
Oil feed pipe to turbocharger 19.....................................................................
Turbocharger to cylinder head (stud) 10.........................................................
Turbocharger to cylinder head (nut) 45...........................................................
Turbocharger to blanking plate 25..................................................................
Turbocharger to EGR valve 25.......................................................................
EGR delivery tube to valve 25........................................................................
EGR delivery tube to mixing tube 25..............................................................
Fuel lift pump to filter (union) 15.....................................................................
Fuel filter from lift pump (banjo bolt) 33...........................................................
Fuel filter to fuel injection pump (banjo bolt) 33..............................................
Fuel injection pump from fuel filter (banjo bolt) 25..........................................
Injector pipes to injectors and fuel injection pump 29.....................................
Spill rail to injectors (banjo bolt) 10.................................................................
Spill rail to injection pump (banjo bolt) 25.......................................................
Boost pipe injection pump (banjo bolt) 10.......................................................
Plug, rear of injection pump 29.......................................................................
PAS pump to mounting plate 25.....................................................................
PAS pump mounting plate to auxiliaries mounting bracket 25........................
PAS pump pulley to hub 25............................................................................
Starter motor (bolt and nut) 45........................................................................
Air conditioning compressor
Compressor mounting bracket to front cover 45.............................................
Compressor to mounting bracket (stud) 8......................................................
Compressor to mounting bracket (nut) 25......................................................
Belt tensioner pulley to tensioner arm 45........................................................
Belt tensioner assembly to front cover plate 25..............................................
Idler pulley to front cover plate 45...................................................................
Compressor belt guard (nut) 25......................................................................
Sensors to water outlet elbow (air/con) 25......................................................
Blanking plug, water outlet elbow (air/con) 25................................................
Generator
Generator mounting bracket to front cover 45................................................
Generator to mounting bracket 85..................................................................
Generator pulley to hub 95.............................................................................
Generator belt guard 25..................................................................................
Generator to auxiliaries mounting bracket 25.................................................
Tachometer electrical connection 4...............................................................

19FUEL SYSTEM
4
REPAIR FUEL LIFT PUMP
Service repair no - 19.45.09
Remove
NOTE: Blank off pipe ends and
connections to prevent ingress of dirt.
1.Disconnect battery.
2.Remove high pressure fuel pipes, injection pump
to injectors.
3.Disconnect fuel inlet and outlet pipes from lift
pump.
4.Remove 2 bolts and withdraw lift pump and
gasket from cylinder block.
Refit
5.Clean mating faces of pump and cylinder block.
6.Fit lift pump to cylinder block with a new gasket,
ensure correct location of operating lever with
camshaft.
7.Secure with bolts. Tighten to
25 Nm (18 lbf/ft).
8.Connect inlet and outlet pipes using new nuts
and olives.
9.Refit injector pipes. Tighten union nuts to
28 Nm
(21 lbf/ft).
FUEL SEDIMENTOR
Service repair no - 19.25.01
Remove
1.Disconnect battery.
2.Disconnect inlet and outlet fuel pipes from
sedimentor.
3.Slacken drain tap and allow sedimentor to
completely drain.
4.Remove 2 bolts, washers and nuts and detach
sedimentor from chassis mounting bracket.
Refit
5.Secure sedimentor to chassis mounting with
fixing bolts.
6.Reconnect inlet and outlet fuel pipes to
sedimentor.
7.Slacken drain plug until diesel free from air
flows, then retighten plug.
8.Prime vehicle fuel system.
See Adjustment,
Priming the fuel system
9.Reconnect battery.

FUEL SYSTEM
5
REPAIR FUEL FILTER ASSEMBLY
Service repair no - 19.25.02
Remove
1.Disconnect battery.
2.Place a suitable container under filter element
and slacken filter bleed screw.
3.Slacken drain tap and allow fuel to drain from
filter element.
4.Slacken fuel inlet and outlet banjo connections.
5.Remove 2 bolts and nuts securing filter head to
inner wing.
6.Remove fuel inlet and outlet banjo bolts and
detach fuel pipes.
7.Remove filter assembly from vehicle. Unscrew
filter element, if necessary.
8.Plug fuel pipe ends to prevent ingress of dirt.Refit
9.Position filter assembly and fit fuel inlet and
outlet pipes using new copper sealing washers
both sides of the banjo connections.
10.Secure filter head to inner wing.
11.Fully tighten banjo connections.
12.Prime fuel system to remove any air trapped in
filter
See Adjustment, Priming the fuel
system
13.Reconnect battery.
FUEL FILTER ELEMENT
Service repair no - 19.25.07
For remove and refit procedure.
See Fuel filter
element

19FUEL SYSTEM
6
REPAIR SIDE MOUNTED FUEL TANK
Service repair no - 19.55.05
NOTE: This fuel tank is standard on 90
models and an option on 110/130 2 door
vehicles fitted with twin tanks.
Remove
WARNING: Before any attempt is made to
start the removal procedure it is vital that
the FUEL HANDLING PRECAUTIONS are
carefully studied and implemented in the interests
of safety.
See INTRODUCTION, Information, Fuel
Handling Precautions
1.Disconnect battery.
2.Remove fuel filler cap.3.Remove fuel tank drain plug, allow fuel to drain
into a clean container and refit plug.
4.Remove RH seat cushion.
5.Release retaining catch and remove seat base
cover to gain access to fuel tank.
6.Disconnect electrical plug from fuel gauge unit.
7.Disconnect fuel supply pipe from tank.
8.Disconnect spill return pipe from fuel tank.
9.Disconnect breather pipe from fuel filler tube.
10.Slacken hose clip and remove filler hose from
filler tube.
11.From rear of tank, remove 2 nuts and washers
securing tank mounting to captive-headed bolts.
12.Support rear of fuel tank and remove captive
bolts.

FUEL SYSTEM
7
REPAIR REV: 05/99
13.Remove single bolt fixing assembly securing
front of tank to chassis mounted bracket.
14.Remove 3 bolts securing tank mounting bracket
to chassis and release bracket.
15.Lower front of tank while turning anti-clockwise
and remove from vehicle.
16.If required, remove tank gauge unit.
See
INSTRUMENTS, Repair, Fuel gauge tank unit
- side fuel tank
orSee INSTRUMENTS,
Repair, Fuel gauge tank unit - rear fuel tank,
110/130
Refit
17.Fit filler hose and clip to tank but do not fully
tighten. Position clip screw so that it is
accessible when tank is fitted.
18.Fit breather hose and secure with clip.
19.Position fuel tank in vehicle and loosely secure
front mounting bracket to tank with special bolt
and rubber bushes.
20.Secure mounting bracket to chassis with 3 bolts
and fully tighten to
20 Nm (15 lbf/ft).
21.Secure rear of tank to chassis mounting and
tighten captive bolt plate fixings to
20 Nm (15
lbf/ft).
22.Fully tighten front fixing bolt assembly to20 Nm
(15 lbf/ft).
23.Fit spill return and fuel supply pipes and secure
union connections.
24.Fit fuel level unit electrical plug.
25.Fit hose to filler tube and tighten upper and lower
clips.
26.Check that drain plug is secure and fill fuel tank.
27.Reconnect battery.
28.Prime fuel system
See Adjustment, Priming
the fuel system
and start engine.
29.Check system for leaks and operation of fuel
gauge.
30.Fit seat base cover and seat cushion.SIDE MOUNTED FUEL TANK - 5 DOOR VEHICLES
Service repair no - 19.55.01
NOTE: This fuel tank is used on 110/130 5
door vehicles fitted with a twin tank
option.
WARNING: Before any attempt is made to
start the removal procedure it is vital that
the FUEL HANDLING PRECAUTIONS,
See
INTRODUCTION, Information, Fuel handling
precautions
are carefully studied and
implemented in the interests of safety.
Remove
1.Disconnect battery.
2.Remove tank drain plug, allow fuel to drain into a
clean container, and refit plug.
3.Remove RH seat cushion.
4.Remove retaining catch and remove seat base
cover to gain access to fuel tank.
5.Disconnect electrical plug from fuel gauge unit.
6.Disconnect fuel supply pipe from tank.
7.Disconnect spill return pipe from tank.
8.Remove 3 bolts securing tank to front mounting
bracket.
9.Support front of tank and remove single fixing
assembly securing tank to rear mounting
bracket.
10.Remove tank from vehicle.
11.If required, remove fuel gauge unit.
See
INSTRUMENTS, Repair, Fuel gauge tank unit
- side fuel tank
orSee INSTRUMENTS,
Repair, Fuel gauge tank unit - rear fuel tank,
110/130
Refit
12.Position fuel tank in vehicle and loosely secure
to rear mounting bracket with special bolt and
rubber bushes.
13.Secure tank to front mounting bracket and
tighten fixings to
20 Nm (15 lbf/ft).
14.Fully tighten rear fixing bolt assembly to20 Nm
(15 lbf/ft).
15.Fit spill return and fuel supply pipes to fuel tank
and securely tighten union connectios.
16.Fit electrical plug to fuel gauge unit.
17.Check that drain plug is secure and fill fuel tank.
18.Reconnect battery.
19.Prime fuel system.
See Adjustment, Priming
the fuel system
and start engine.
20.Check system for leaks and operation of fuel
gauge.
21.Fit seat base cover and seat cushion.

FUEL SYSTEM
9
REPAIR REV: 05/99
11.Remove 2 nuts that secure front fixing assembly
of the tank to chassis mounting bracket.
12.Remove tank rear mounting nuts.
13.With care, lower tank sufficiently to enable nut
and olive of spill return to be disconnected from
elbow in centre of tank.
14.Continue to lower tank until it can be removed
from vehicle.
NOTE: On later vehicles a separate stone
guard is fitted and is attached to the tank
with the existing front and rear fixings.
15.If required, remove tank gauge unit.
See
INSTRUMENTS, Repair, Fuel gauge tank unit
- side fuel tank
orSee INSTRUMENTS,
Repair, Fuel gauge tank unit - rear fuel tank,
110/130
Refit
16.If applicable, locate stone guard under tank.
17.Raise rear tank into position and connect spill
return pipe to the elbow with the nut and olive.
18.Continue to raise tank so that front and rear
mounting bolts locate in respective tank flange
holes.
19.Fit and tighten fixings to
20 Nm (15 lbf/ft).
20.Connect fuel suppnly pipe to the tank unit.
21.Fit fuel filler hose and breather pipe to filler tube
and secure with retaining clips.
22.Fit LH lashing eye to chassis.23.Fit anti-roll bar chassis mountings.
See REAR
SUSPENSION, Repair, Anti-roll bar
24.Check that drain plug is secure and fill fuel tank.
25.Reconnect battery.
26.Prime fuel system.
See Adjustment, Priming
the fuel system
and start engine.
27.Check system for leaks and operation of fuel
gauge.

FUEL SYSTEM
15
REPAIR TURBOCHARGER OIL DRAIN PIPE
Service repair no - 19.42.12
Remove
1.Disconnect battery.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
front pipe
3.Unscrew union and disconnect oil drain pipe
from cylinder block.
4.Remove 2 bolts securing oil drain pipe to
turbocharger.
5.Remove drain pipe and discard gasket.
6.Plug connections to prevent ingress of dirt.
Refit
7.Ensure mating surfaces of oil pipe, turbocharger
and engine block are clean.
8.Using new gasket, fit oil drain pipe to
turbocharger. Tighten bolts to
25 Nm (18 lbf/ft).
9.Fit drain pipe to cylinder block and tighten union
connector to
38 Nm (28 lbf/ft).
10.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust front
pipe
11.Check/top-up engine oil level.See SECTION
10, Maintenance, Under bonnet maintenance
12.Reconnect battery.