1996 LAND ROVER DEFENDER drain bolt

37MANUAL GEARBOX
6
REPAIRREV: 05/99 78.Position crossmember and locate over fixing
studs of LH and RH gearbox mounting rubbers.
79.Align crossmember and secure to chassis with 4
nuts and bolts on each side.
NOTE: Fit battery earth strap retaining clip
to LH top bolt.
80.Fit intermediate silencer.
See MANIFOLD AND
EXHAUST SYSTEM, Repair, Intermediate
pipe - 90
orSee MANIFOLD AND EXHAUST
SYSTEM, Repair, Intermediate pipe - 110/130
.
81.Fit front pipe to exhaust manifold
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust front pipe
.
82.Fit rear propeller shaft to transmission brake
drum. Tighten nuts to
47 Nm (33 lbf/ft).
83.Remove 3 bolts securing support cradle to
transmission and remove hoist.
84.Reconnect battery earth strap to transfer box
fixing.
85.Connect speedometer cable to transfer box and
secure with retaining clip.
86.Coat both sides of clutch slave clinder backing
plate with Hylomar P232M waterproof sealant.
87.Locate backing plate on slave cylinder.
88.Fit slave cylinder to bell housing, engaging
push-rod through centre of dust cover, and with
bleed screw uppermost. Tighten bolts to
25 Nm
(18 lbf/ft).
89.Fit front propeller shaft to transfer box. Tighten
nuts to
47 Nm (33 lbf/ft).
90.Refill main gearbox and transfer boxSee
MAINTENANCE , Under vehicle maintenance
.
91.Feed transmission brake cable through heel
board and ensure grommet is correctly located.
NOTE: Apply a soap solution to aid fitment
of cable.
92.Lower vehicle on ramp.
93.Fit ties to secure gearbox harness to
transmission breather pipes.
94.Fit breather pipe retaining clip to rear of engine.
95.Reconnect charge air hose at turbocharger.
96.Reconnect intake hose at induction manifold. If
EGR system is fitted, reconnect intake hose at
intercooler.
97.Reconnect radiator top hose at thermostat
housing.
98.Fit viscous fan unit
See COOLING SYSTEM,
Repair, Viscous coupling and fan
.
99.Reconnect battery.100.Refill cooling system
See COOLING SYSTEM,
Adjustment, Drain and refill cooling system
.
101.Connect cable clevis to handbrake lever and fit
handbrake gaiter.
102.Locate insulation pad over gear levers and fit to
tunnel cover.
103.Fit gear lever with gaiter to lower lever spline
and secure with retaining nut.
104.Fit gear lever cover.
105.Fit gear lever and transfer box lever knobs.
106.Fit gearbox cover carpet.
107.Check operation of handbrake and adjust as
necessary
See MAINTENANCE , Under
vehicle maintenance
.

41TRANSFER GEARBOX
2
FAULT DIAGNOSIS OIL LEAKS
Verify that oil leak is from transfer box and not main
gearbox before proceeding with checks.
Prior to road test
1.Check oil level in transfer box is correct.
2.Check tightness of level and drain plugs.
3.Check breather system for blockage. To validate
system pipe must be removed, inspected,
rectified as necessary and refitted.
4.Remove all traces of oil from exterior of transfer
box.
Take vehicle for short road test.
5.Identify source of leaks and rectify as follows.
Front or rear output seal leaking:-
1.Drain oil and remove leaking output flange.
2.Inspect seal track on flange for surface damage.
If damaged renew component.
3.Remove and discard oil seal.
4.Inspect seal locating bore and remove any sharp
edges which may damage new oil seal.
5.Fit new seal.
6.Fit output flange and all other parts.
7.Add oil to correct level into gearbox
See
SECTION 10, Maintenance, Under vehicle
maintenance
.
Cover plate sealant leaking.
1.Drain oil and remove leaking cover plate.
2.Remove all traces of joint sealant from both joint
faces.
3.Degrease all components and apply a thin film of
Hylomar sealant, to both joint faces.
4.Apply thread sealant to bolts which come into
contact with gearbox oil.
5.Refit cover plate.
CAUTION: Care must be taken not to
overtighten fixings.Leak between main and transfer gearboxes.
1.Site vehicle onto a ramp .
2.Select neutral in transfer box and select 4th gear
in main gearbox.
3.Run engine at 2000 rpm with clutch/drive
engaged.
4.Observe joint between main and transfer boxes.
5.If oil leak is found establish if it is gear oil.
6.If so, leak is originating from transfer box.
7.Check two inner (main/transfer) bolts are oil
tight, as these holes are tapped into main
transfer case.
8.Remove transfer box to inspect mainshaft collar
seal track condition, and front face of transfer
case for porosity
See Repair, Transfer
gearbox
.
9.If these areas require servicing, transfer gearbox
input seal must also be renewed.
CAUTION: Avoid damaging new seal lip
and ensure seal is fitted flush with
machined face. Also ensure new seal is
not damaged when refitting transfer gearbox.
10.If red ATF type oil is seen leaking during
workshop test, investigate main gearbox for
cause of leak.
Detent plug or electrical switch leaks.
1.Detent plugs and electrical switches do not
usually leak. It must be noted that they fit into
open tapped holes in transfer case and therefore
should be considered when looking for source of
leak.

TRANSFER GEARBOX
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Transfer gearbox
Pinch bolt - operating arm to crank arm 9......................................................
End cover gear change housing 9.................................................................
Bottom cover to transfer case 25....................................................................
Front output housing to transfer case 25........................................................
Cross shaft housing to front output housing 25...............................................
Gear change housing 25.................................................................................
Pivot shaft to link arm 25.................................................................................
Connecting rod to adjustable clevis 25...........................................................
Anti-rotation plate intermediate shaft 25.........................................................
Front output housing cover 25........................................................................
Pivot bracket to extension housing 25............................................................
Finger housing to front output housing 25......................................................
Bearing housing to transfer case 25...............................................................
Brake drum to coupling flange 25...................................................................
Bearing housing cover to transfer gearbox 45................................................
Rear output speedometer housing to transfer gearbox 45..............................
Selector finger to cross shaft high/low 25.......................................................
Selector fork, high/low to shaft 25...................................................................
Transmission brake to speedometer housing 72............................................
Gate plate to grommet plate 9.......................................................................
Gearbox to transfer case 45...........................................................................
Oil drain plug 30..............................................................................................
Oil filler/level plug 30.......................................................................................
Differential case (front to rear) 60...................................................................
Output flanges 162...........................................................................................
Differential case rear stake nut 72..................................................................
Transfer breather 15.......................................................................................
Transfer box front drive flange to drive shaft 45..............................................
Transfer box rear drive flange to drive shaft 45..............................................
Transfer gearbox mounting brackets to chassis 30........................................
Mounting brackets to transfer gearbox 55......................................................
Mounting rubbers to mounting brackets 21.....................................................

REAR AXLE AND FINAL DRIVE
1
REPAIR REAR AXLE
Service repair no - 51.25.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
the axle when lowering or repositioning
axle.
1.Drain brake system.
2.Support chassis rear.
3.Remove road wheels.
4.Support axle weight with hydraulic jack.
5.Disconnect shock absorbers.
6.Disconnect flexible brake hose at RH chassis
side member and breather hose at banjo
connection on axle casing.
7.Disconnect lower links at axle.8.Mark differential and propeller shaft flanges with
identification marks for assembly.
9.Remove 4 nuts and bolts, lower propeller shaft
and tie to one side.
10.Disconnect pivot bracket ball joint at axle
bracket.
11.Release bolts and remove coil spring retaining
plates.
12.Lower axle and remove road springs.
13.If applicable, remove anti-roll bar links at axle
See REAR SUSPENSION, Repair, anti-roll
bar
.
14.Remove axle assembly.

REAR AXLE AND FINAL DRIVE
7
REPAIR DIFFERENTIAL ASSEMBLY - 90
Service repair no - 51.15.01
Remove
1.Using suitable container, drain axle oil.
2.Mark differential and propeller shaft flanges to
facilitate reassembly.
3.Remove 4 bolts and disconnect propeller shaft
from differential. Tie aside.
4.Remove 5 hub drive member bolts and withdraw
axle half shafts sufficiently to disengage from
differential unit.
5.Remove 10 nuts securing differential to axle
case.
6.Withdraw differential unit.
NOTE: The differential unit can only be
serviced as a complete assembly with
matching drive pinion. For advice ring
Land Rover Service Department.Refit
7.Ensure mating faces are clean and apply a bead
of RTV sealant to axle case.
8.Support differential unit and position on axle
casing.
9.Secure with self locking nuts and tighten to
40
Nm (30lbf/ft).
10.Align marks on flanges and secure propeller
shaft to differential. Tighten bolts to
48 Nm (35
lbf/ft).
11.Refit half shafts, using new drive member
gaskets. Tighten bolts to
65 Nm (48 lbf/ft).
12.Refill axle oil with approved lubricantSee
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended lubricants and
fluids
.

54FRONT AXLE AND FINAL DRIVE
2
OVERHAUL FRONT STUB AXLE, CONSTANT VELOCITY JOINT
AND SWIVEL PIN HOUSING
Service repair no - 60.15.43.
Remove stub axle, axle shaft and constant
velocity joint.
1.Remove front hub assembly
See Repair, Front
hub assembly
.
2.Drain swivel pin housing and refit plug.
NOTE: On later vehicles the swivel pin
housing is filled with grease for life, the
level and drain plugs being deleted.
3.Remove 6 bolts retaining stub axle to swivel
housing.
4.Remove mud shield.
5.Remove stub axle and joint washer.
6.Wthdraw axle shaft and constant velocity joint
from axle casing.
Remove constant velocity joint from axle shaft
7.Hold axle shaft firmly in a soft jawed vice.
8.Using a soft mallet drive constant velocity joint
from shaft.
9.Remove circlip and collar from axle shaft.
Constant velocity joint
10.Mark positions of constant velocity joint, inner
and outer race and cage for reassembly.
11.Swivel cage and inner race to remove balls.

FRONT AXLE AND FINAL DRIVE
5
OVERHAUL 38.Place retaining plate, joint washer and oil seal
over axle flange ready for assembly.
39.Fit swivel bearing housing to axle flange with 7
bolts. Tighten to
73 Nm (54 lbf/ft).
40.Grease and fit upper and lower swivel pin taper
roller bearings.
41.Position swivel pin housing over swivel bearing
housing.
42.Coat joint washer both sides with sealing
compound and position on lower swivel pin.
43.Loosely fit brake shield bracket plus lower swivel
pin with lug outboard to swivel pin housing.
44.Loosely fit top swivel pin plus existing shims and
brake hose bracket to swivel pin housing.
45.Apply Loctite 270 or equivalent to lower swivel
pin bolts.
78 Nm (58 lbf/ft),bend over lock tabs.
46.Tighten top swivel pin bolts to
78 Nm (58 lbf/ft).
Check and adjust preload on bearings
NOTE: Swivel housing oil seal and axle
should not be fitted.
47.Attach a spring balance to ball joint bore and pull
balance to determine effort required to turn
swivel pin housing.
Resistance, once initial inertia has been
overcome, should be1.16 to 1.46 kg.Adjust by
removing or adding shims to top swivel pin.
48.When setting is correct remove top swivel bolts,
apply Loctite 270 or equivalent. Refit bolts and
tighten to
78 Nm (58 lbf/ft),and bend over lock
tabs.
49.Apply recommended grease between lips of
swivel oil seal.50.Fit oil seal, joint washer and retaining plate with
7 bolts and spring washers. Tighten to
11 Nm (8
lbf/ft).
51.Fit tie rod and drag link and secure with new
cotter pins. Tighten fixing to
40 Nm (30 lbf/ft).
52.Fit brake disc shield.
53.Loosely fit lock stop bolt and nut.
54.Apply a recommended grease between lips of
swivel housing oil seal.
55.Secure oil seal with retaining plate and securing
bolts. Tighten to
11 Nm (8 lbf/ft).
56.Fit track-rod and drag link and secure with new
cotter pins.
57.Loosely fit lock stop bolt for later adjustment.
58.Fit brake disc shield.
Fit driveshaft and stub axle
59.Insert axle shaft, and when differential splines
are engaged, push assembly in fully.
CAUTION: Take care not to damage axle
shaft oil seals.
60.Place a new joint washer in position on swivelpin
housing to stub axle mating face. Coat threads
of stub axle bolts with Loctite 270.
61.Fit stub axle with flat at 12 O'clock position.
CAUTION: Ensure that constant velocity
joint bearing journal is butted against
thrust ring on stub axle before stub axle is
secured.
62.Place mud shield in position and secure stub
axle to swivel pin housing with 6 bolts and
tighten evenly to
65 Nm (48 lbf/ft).
63.Fit brake jump hoses to brake jump hose
bracket.
64.Fit complete front hub assembly
See Repair,
Front hub assembly
.
65.Check swivel pin housing oil drain plug is fitted.
66.Fill swivel assembly to correct level, with new oil
See SECTION 10, Maintenance, Under
vehicle maintenance
.
NOTE: On later vehicles fill swivel pin
housing with 0.33 Litres of Molytex EP 00
grease.
67.Set steering lock stop bolts
See STEERING,
Adjustment, Steering lock stops
.

57STEERING
4
REPAIR POWER STEERING BOX
Service repair no - 57.10.01
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
remove and refit procedures are required, it may
be necessary to remove the undertray
See
CHASSIS AND BODY, Repair, Front undertray
.
General precautions
·Whenever any part of system, is removed or
disconnected, utmost cleanliness must be
observed.
·Disconnected ports and hoses must be
plugged to prevent ingress of dirt. If metal
sediment is found in system, establish cause,
rectify and flush system.
·Do not start engine until reservoir is full as
pump will be damaged.
·Metric pipe fittings are used with 'O' ring pipe
ends on fittings to steering box.
·Follow normal 'O' ring replacement procedure
whenever pipes are disconnected.
·Ensure compatible metric components when
fitting replacement pipes.
CAUTION: After refitting steering linkage
parts follow correct procedure to ensure
that road wheels, steering box and
steering wheel are correctly positioned relative to
each other when in straight ahead condition.
NOTE: When drag link is disconnected
from steering box, travel available at
steering wheel to each full lock is not
equal.
Remove
1.Site vehicle on level surface.
2.Apply park brake, chock rear wheels, raise
vehicle and locate axle stands. Alternatively,
raise vehicle on a hoist.
3.Remove road wheel.
4.Remove panhard rod
See FRONT
SUSPENSION, Repair, Panhard rod
.
5.Disconnect steering damper from drag link.
6.Disconnect drag link from drop arm, see J6305
on opposite page, using a suitable extractor.
7.Slacken, but do not remove nut securing tie bar
to mounting arm.8.Remove 2 bolts securing tie bar to steering box
and move aside.
9.Remove filler cap from power steering fluid
reservoir.
10.Position suitable container under steering box.
11.Disconnect feed and return pipes from steering
box and drain fluid.
12.Plug open pipes and steering box ports to
prevent ingress of dirt. Refit fluid reservoir filler
cap.
13.Centralise steering
See Centralise steering
box
.
14.Remove pinch bolt securing lower shaft
universal joint to power steering box.
15.Remove 4 bolts and 2 tab washers securing
steering box to chassis side member.
16.Withdraw steering box.
17.Clean all mounting faces, unions etc. prior to
refitting.
Refit
18.Position steering box to chassis side member,
ensuring locating peg is engaged. Fit tab
washers and tighten bolts to
81 Nm (60 lbf/ft).
19.Fit pinch bolt and nut securing universal joint to
power steering box spline. Tighten to
25 Nm (18
lbf/ft).
20.Secure tie bar to mounting arm and steering box.
Tighten fixings to
81 Nm (60 lbf/ft),starting with
tie bar to mounting nut, then loosen fixings by
one complete turn.
21.Check steering box and adjust if necessary
See
Adjustment, Power steering box - adjust
.
22.Refit drag link to drop arm and tighten nut to
40
Nm (30 lbf/ft).
Fit new split pin to retaining nut.