1996 LAND ROVER DEFENDER ground

FRONT SUSPENSION
1
DESCRIPTION AND OPERATION DESCRIPTION
The front suspension design allows maximum wheel
travel and axle articulation providing good ground
clearance without loss of traction or directional
stability.
Long radius arms are fitted to the front axle and
provide maximum axle articulation which is vital for off
road performance. The radius arms are secured to
fabricated mounting brackets welded to the front axle.
Flexible rubber bushes are used on a stem end joint
to secure the rear of the radius arms to mountings on
the chassis cross member.
A panhard rod, which ensures that the front axle
remains centrally located, is fitted transversely and
also uses ferrule rubber bush mountings at both axle
and chassis locations.Two rubber bearing bushes, with retaining straps,
secure the rear of the anti-roll bar to the chassis
mountings, while bushed links support the front of the
bar to the front axle.
Conventional long travel coil springs and hydraulic
shock absorbers are used to control body movement
in all conditions. The shock absorbers are secured to
fabricated towers which are bolted to the chassis. The
upper and lower fixings use a single location stud with
flexible rubber bushes, support washers and securing
nuts. Retaining plates are used to secure the coil
springs to the fabricated towers and axle mountings.
Rubber bump stops are fitted underneath the chassis,
adjacent to the front road springs, and prevent
possible damage that could occur should there be
excessive axle to chassis movement.
Front suspension
1.Panhard rod
2.Radius arms
3.Coil springs
4.Shock absorber
5.Anti-roll bar

BRAKES
1
REPAIR GENERAL BRAKE SERVICE PRACTICE
Brake fluid precautions
WARNING: Do not allow brake fluid to
come into contact with eyes or skin.
CAUTION: Brake fluid can damage
paintwork, if spilled wash off immediately
with plenty of clean water.
CAUTION: Use only correct grade of brake
fluid. If an assembly fluid is required use
ONLY brake fluid. Do NOT use mineral oil,
i.e. engine oil etc.
CAUTION: Thoroughly clean all brake
calipers, pipes and fittings before
commencing work on any part of the brake
system. Failure to do so could cause foreign
matter to enter the system and cause damage to
seals and pistons which will seriously impair the
efficiency of the brake system. To ensure the
brake system efficiency is not impaired the
following warnings must be adhered to :-
·DO NOT use any petroleum based cleaning
fluids or any proprietary fluids containing
petrol.
·DO NOT use brake fluid previously bled from
the system.
·DO NOT flush the brake system with any fluid
other than the recommended brake fluid.
The brake system should be drained and flushed
at the recommended service intervals.
Cover all electrical terminals carefully to make
absolutely certain that no fluid enters the
terminals and plugs.FLUID LEVEL CHECK/TOP UP
WARNING: Clean reservoir body and filler
cap before removing cap. Use only fluid
from a sealed container.
1.Park vehicle on level ground.
2.Check level is between 'MIN' and 'MAX' marks.
3.If level is below 'MIN' mark top up fluid level to
'MAX' mark on reservoir, using correct fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended lubricants and
fluids
CAUTION: Do not fill reservoir above
maximum line.

70BRAKES
16
REPAIRREV: 05/99 TRANSMISSION BRAKE SHOES
Service repair no - 70.45.18
Remove
1.Park vehicle on level ground, chock road wheels
and release handbrake. Alternatively, raise
vehicle on a ramp.
2.Disconnect rear propeller shaft from
transmission output flange at brake drum.
3.Slacken off transmission brake drum adjustment
bolt.
4.Remove single screw securing brake drum to
output flange.
5.Withdraw drum to expose brake assembly.
6.Release top and bottom springs from brake
shoes, see J6337.
7.Grip dished washer with a pair of pliers, depress
washer and turn through 90°.
8.Remove dished washer, complete with hold
down spring and pin from both shoes.
9.Move brake shoes out from adjuster slides,
release from abutment plate and remove from
backplate.
10.Check that springs are satisfactory for continued
use. If new brake shoes are to be fitted, the
srings should also be renewed.Refit
11.Locate RH brake shoe in slide and secure brake
shoe and lever assembly to backplate with hold
down pin, spring and dished washer.
12.Locate LH brake shoe in slide and fit abutment
plate between both brake shoes. Secure LH
shoe with hold down pin, spring and dished
washer.
13.Fit pull-off springs to brake shoes.
14.Fit brake drum. Tighten screw to
25 Nm (18
lbf/ft).
15.Check that hand brake lever is released.
16.Screw in and tighten adjuster bolt until brake
drum will not rotate by hand.
17.Tighten adjuster bolt to
25 Nm (18 lbf/ft)to
ensure brake drum is locked.
18.Slacken off adjuster bolt by 1.5 turns to give
shoes a running clearance. Check that the drum
is free to rotate.
19.Fit propeller shaft to output flange. Tighten
fixings to
46 Nm (34 lbf/ft).
20.Remove wheel chocks and check operation of
handbrake.

BRAKES
17
REPAIR HANDBRAKE CABLE
Service repair no - 70.35.25
Remove
1.Park vehicle on level ground, chock road wheels
and release handbrake. Alternatively, raise
vehicle on ramp.
2.Remove 3 trim studs and lift up handbrake
gaiter.
3.Remove split pin, clevis pin, washer and
disconnect cable from handbrake lever.
4.Slacken off transmission brake drum adjusting
screw.
5.Disconnect propeller shaft from output flange.
6.Remove retaining screw and withdraw brake
drum.
7.Release handbrake cable clevis from abutment
on cable lever, see J6337, and pull through
aperture in back plate.
8.Pull cable from heelboard and remove from
vehicle.
Refit
9.Feed new cable through heelboard ensuring
rubber grommet is correctly located.
10.Position cable over guide plate, insert through
backplate and connect to cable lever.
11.Fit cable to handbrake lever and secure with
clevis pin and split pin.
12.Fit handbrake gaiter.
13.Fit brake drum. Tighten screw to
25 Nm (18
lbf/ft).
14.Screw in and tighten adjuster bolt until brake
drum will not rotate by hand.
15.Tighten adjuster bolt further to
25 Nm (18 lbf/ft)
to ensure brake drum is locked.
16.Slacken off adjuster bolt by 1.5 turns to give
brake shoes running clearance. Check that the
drum is free to rotate.
17.Slacken locknut and adjust cable to give the
handbrake pawl two notches free movement on
the rachet before being fully operational on third
notch (brake shoes are fully expanded against
drum).
NOTE: Cable adjustment is for a new cable
or to compensate for cable stretch. Cable
adjustment must not be used to take up
brake shoe wear.
18.Fit propeller shaft to output flange. Tighten
fixings to
46 Nm (34 lbf/ft).
19.Remove wheel chocks and check operation of
handbrake.

ELECTRICAL
1
DESCRIPTION AND OPERATION ELECTRICAL EQUIPMENT
Description
The electrical system is Negative ground, and it is
most important to ensure correct polarity of electrical
connections at all times. Any incorrect connections
made when reconnecting cables may cause
irreparable damage to semi-conductor devices used in
generator and regulator. Incorrect polarity would also
seriously damage any transistorized equipment such
as a radio.
WARNING: During battery removal or
before carrying out any repairs or
maintenance to electrical components
always disconnect battery negative lead first. If
positive lead is disconnected with negative lead in
place, accidental contact of wrench to any
grounded metal part could cause a severe spark,
possibly resulting in personal injury. Upon
installation of battery positive lead should be
connected first.
GENERATOR
The generator is a three phase, field sensed unit. The
rotor and stator windings produce three phase
alternating current, AC, which is rectified to direct
current, DC. The electronic voltage regulator unit
controls generator output voltage by high frequency
switching of the rotor field circuit. Use only correct
replacement drive belt. Occasionally check that
engine and generator pulleys are accurately aligned.
It is essential that good electrical connections are
maintained at all times. Of particular importance are
those in the charging circuit (including those at
battery) which should be occasionally inspected to
see that they are clean and tight. In this way any
significant increase in circuit resistance can be
prevented.Do not disconnect battery cables while engine is
running or damage to semi-conductor devices may
occur. It is also inadvisable to break or make any
connections in the generator charging and control
circuits while engine is running.
The electronic voltage regulator employs micro-circuit
techniques resulting in improved performance under
difficult service conditions. The whole assembly is
encapsulated in silicone rubber and housed in an
aluminium heat sink, ensuring complete protection
against adverse effects of temperature, dust, and
moisture etc.
The regulating voltage is set during manufacture to
give required regulating voltage range of 14.2±0.2
volts, and no adjustment is necessary. The only
maintenance needed is occasional check on terminal
connections and wiping with a clean dry cloth.
The generator system provides for direct connection
of a charge (ignition) indicator warning lamp, and
eliminates the need for a field switching relay or
warning light control unit. In the event of bulb failure,
an 'exciter' voltage is supplied through a resistor,
wired in parallel to the bulbs, ensuring that generator
output is maintained. The lamp should be checked
regularly.
When using rapid charge equipment to re-charge
battery, the battery must be disconnected from the
vehicle.

86ELECTRICAL
2
REPAIR BATTERY
Service repair no - 86.15.01
NOTE: If the vehicle is fitted with a battery
backed-up alarm sounder, disconnecting
the vehicle battery will cause the alarm to
sound unless the following procedure is followed:
1.Remove LH front seat cushion.
2.Release retaining clip and remove battery
access cover.
3.Slacken battery negative lead clamp bolt.
4.Turn starter switch 'on'.
5.Turn starter switch 'off' and remove key.
6.Disconnect battery WITHIN 15 SECONDS.
If alarm is accidentally activated, ensure sounder is
connected and silence by turning the starter switch to
position 'II'.Remove
WARNING: During battery removal or
before carrying out any repairs or
maintenance to electrical components
always disconnect negative lead first. If positive
lead is disconnected with negative lead in place,
accidental contact of a wrench to any grounded
metal part could cause a severe spark, possibly
resulting in personal injury. Upon installation of
battery always connect positive lead first.
1.Remove LH front seat cushion.
2.Release retaining clip and remove battery
access cover.
3.Disconnect both battery leads, negative first.
4.Slacken securing nuts and move battery clamp,
with 'J' bolts aside.
5.Remove battery.
NOTE: Coat battery clamps and terminals
with petroleum jelly before refitting.
Refit
6.Position battery and secure with clamp. Ensure
'J' bolts are hooked correctly under retaining
brackets on base of battery box.
7.Reconnect battery leads, positive lead first.
8.Fit battery access cover.
9.Fit seat cushion.

86ELECTRICAL
24
REPAIRREV: 05/99 HEADLAMP BEAM ALIGNMENT
Service repair no - 86.40.17
Check
Check main beam alignment using beam setting
equipment. Should this not be available the beam can
be temporarily checked and adjusted as follows:-
1.Position vehicle, unladen, on level ground with
tyres correctly inflated, approximately 4 metres
from a wall or screen, marked as illustrated
below.
2.The beam centres 'A' are measured horizontally
on the vehicle and dimension 'B' vertically from
the ground.
3.Switch on main beam and adjust setting, as
necessary, with trimmer screws.On vehicles fitted with headlamp levelling units, check
and adjust headlamp beam alignment as previously
described, with fascia mounted levelling switch at
position '0'. The headlamps can then be adjusted,
according to load conditions, as follows:-
Position '0' - Driver only, or driver and all front seats
occupied (loadspace empty).
Position '1' - All seats occupied (loadspace empty).
Position '2' - All seats occupied by adults and
loadspace loaded to maximum rear axle weight.
Position '3' - Driver only with loadspace loaded to
maximum rear axle weight.