1996 LAND ROVER DEFENDER lock

CHASSIS AND BODY
39
REPAIR ACCESS PANEL - FRONT UNDERTRAY
Service repair no - 76.11.85 - Access panel
Service repair no - 76.11.83 - Acoustic pad
The access panel is provided in the front undertray to
enable fitment of the wading plug into the engine
timing cover.
Remove
1.Raise vehicle on ramp.
2.Remove 5 bolts securing access panel to front
undertray.
3.Remove access panel.
4.If necessary, remove 5 fasteners and release
acoustic pad from access panel.
Refit
5.If applicable, fit acoustic pad to access panel.
6.Fit access panel to front undertray, Tighten
fixings to
14 Nm (10 lbf/ft).
7.Lower ramp.ACCESS PANEL - REAR UNDERTRAY
Service repair no - 76.11.84
The access panel is provided in the rear undertray to
enable fitment of the wading plug or timing tool
LRT-12-044in the flywheel housing, and access to
the engine oil sump drain plug.
Remove
1.Raise vehicle on ramp.
2.Rotate access panel anti-clockwise to release
locking flanges.
3.Remove access panel from undertray.
Refit
4.Locate access panel flanges in undertray
apertures.
5.Rotate panel clockwise to secure in undertray.
6.Lower ramp.

82AIR CONDITIONING
6
ADJUSTMENT SYSTEM TEST
1.Place the vehicle in a ventilated, shaded area
free from excessive draught, with the doors and
windows open.
2.Check that the surface of the condenser is not
restricted with dirt, leaves, flies, etc. Do not
neglect to check the surface between the
condenser and the radiator. Clean as necessary.
3.Switch on the ignition and the air conditioner air
flow control. Check that the blower is operating
efficiently at low, medium and high speeds.
Switch off the blower and the ignition.
4.Check that the evaporator condensate drain
tubes are open and clear.
5.Check the tension of the compressor driving belt,
and adjust if necessary.
6.Inspect all connections for the presence of
refrigerant oil. If oil is evident, check for leaks,
and repair as necessary.
NOTE: The compressor oil is soluble in
Refrigerant R134a and is deposited when
the refrigerant evaporates from a leak.
7.Start the engine.
8.Set the temperature controls to cold and switch
the air conditioner blower control on and off
several times, checking that the magnetic clutch
on the compressor engages and releases each
time.
9.With the temperature control at maximum
cooling and the blower control at high speed,
warm up the engine and fast idle at 1000
rev/min.
10.Repeat at 1800 rev/min.
11.Gradually increase the engine speed to the high
range and check the sight glass at intervals.
12.Check for frosting on the service valves.
13.Check the high pressure hoses and connections
by hand for varying temperature. Low
temperature indicates a restriction or blockage at
that point.
14.Switch off the air conditioning blower and stop
the engine.
15.If the air conditioning equipment is still not
satisfactory, carry out a pressure test as
previously described in this section.PRECAUTIONS IN HANDLING REFRIGERANT
LINES
WARNING: Wear eye and hand protection
when disconnecting components
containing refrigerant. Plug all exposed
connections immediately.
1.When disconnecting any hose or pipe
connection the system must be discharged of all
pressure. Proceed cautiously, regardless of
gauge readings. Open connections slowly,
keeping hands and face well clear, so that no
injury occurs if there is liquid in the line. If
pressure is noticed, allow it to bleed off slowly.
2.Lines, flexible end connections and components
must be capped immediately they are opened to
prevent the entrance of moisture and dirt.
3.Any dirt or grease on fittings must be wiped off
with a clean alcohol dampened cloth. Do not use
chlorinated solvents such as trichloroethylene. If
dirt, grease or moisture cannot be removed from
inside the hoses, they must be replaced with
new hoses.
4.All replacement components and flexible end
connections must be sealed, and only opened
immediately prior to making the connection.
5.Ensure the components are at room temperature
before uncapping, to prevent condensation of
moisture from the air that enters.
6.Components must not remain uncapped for
longer than 15 minutes. In the event of delay, the
caps must be fitted.
7.Receiver/driers must never be left uncapped as
they contain Silica Gel crystals which will absorb
moisture from the atmosphere. A receiver/ drier
left uncapped must not be used, fit a new unit.
8.The compressor shaft must not be rotated until
the system is entirely assembled and contains a
charge of refrigerant.
9.A new compressor contains an initial charge of
refrigerant oil. The compressor also contains a
holding charge of gas when received which
should be retained by leaving the seals in place
until the pipes are re-connected.
10.The receiver/drier should be the last component
connected to the system to ensure optimum
dehydration and maximum moisture protection of
the system.

82AIR CONDITIONING
6
REPAIR 9.Remove plug connector from resistor.
10.Remove relay from connecting block to gain
access to fixing screw.
11.Remove screw and release relay connector
block. Retain relay in connector block.
12.Remove screw and detach air conditioning 30
amp fuse bracket from resistor. Refit both
resistor retaining screws.
13.Using suitable pipe clamps, clamp heater matrix
feed and return hoses at base of heater/cooler
unit. Release retaining clips and remove hoses.
14.From inside vehicle remove front passenger
carpet, if fitted.
15.Remove retaining screws and fold back footwell
insulation.
16.Remove 2 bolts securing heater/cooler unit lower
mounting bracket to bulkhead.
17.From inside engine compartment remove 2 bolts
securing top heater/cooler unit mounting bracket
to engine bulkhead. This also releases earthing
leads.
18.Remove bolt securing support bracket to front of
heater/cooler casing.19.Lift heater/cooler unit clear of air duct seal and
remove from vehicle.
20.Discard all pipe connection 'O' rings.
Refit
21.Coat unions, threads and new 'O' rings with
refrigerant oil prior to reassembly.
22.Position heater/cooler unit in engine
compartment and locate with air duct seal.
23.Secure unit top and bottom mounting brackets to
bulkhead and support bracket to front of unit
casing. Fully tighten fixing bolts when unit is
correctly positioned.
24.Fit footwell insulation.
25.Reconnect heater matrix hoses.
26.Fit air conditioning fuse bracket, relay connector
block, relay and resistor plug connector.
27.Fit control cable to evaporator air flap operating
rod, using a new clip.
28.Fit pipe connector to vacuum switch.
29.Connect compressor clutch switch multi-plug.
30.Connect high and low pressure pipes to
evaporator.
31.Fit expansion tank
See COOLING SYSTEM,
Repair, Expansion tank.
32.Evacuate and recharge air conditioning system
See Adjustment, Refrigerant recovery,
recycling, recharging.
33.Reconnect battery.

AIR CONDITIONING
13
REPAIR HEATER/COOLER UNIT - RH DRIVE
Service repair no - 82.25.21
Remove
1.Disconnect battery.
2.Recover refrigerant from air conditioning system
See Refrigerant recovery, recycling,
recharging.
3.Release ties, remove insulation cover and
disconnect evaporator low pressure pipe.
4.Disconnect evaporator high pressure pipe.
5.Discard all pipe connection 'O' rings. Cap or plug
all connections to prevent ingress of dirt and
moisture.
6.Using suitable pipe clamps, clamp heater matrix
feed and return pipes at heater/cooler unit.
7.Remove screw securing air control flap solenoid.
8.Disconnect 2 leads from thermostat.
9.Remove pipe from water valve vacuum switch.
10.Remove retaining clip and disconnect control
cable from evaporator flap operating rod.
11.Remove screw and release outer cable retaining
bracket.12.Disconnect blower motor wiring plugs and
release harness retaining clip from housing.
13.Remove bolt securing front support bracket to
blower motor housing. If necessary, remove
blower motor resistor block to facilitate
operation.
14.From inside vehicle remove front passenger
carpet, if fitted.
15.Remove fixing screws and fold back footwell
insulation.
16.Remove 4 bolts securing heater/cooler unit lower
mounting bracket to bulkhead. Ensure spacing
washers from two innermost bolts are retrieved
from engine bulkhead side.
17.From inside engine compartment remove 2 bolts
securing top heater/cooler unit mounting bracket
to engine bullkhead.
18.Lift heater/cooler unit clear of air duct seal and
remove from vehicle.

82AIR CONDITIONING
14
REPAIR Refit
19.Coat unions, threads and new 'O' rings with
refrigerant oil prior to reassembly.
20.Position heater/cooler unit in engine
compartment and locate with air duct seal.
21.Secure unit top and bottom mounting brackets to
bulkhead and support bracket to front of unit
casing. Fully tighten fixing bolts when unit is
correctly positioned.
22.If applicable, fit blower motor resistor block to
vehicle wing.
23.Connect blower motor wiring plugs.
24.Fit footwell insulation and carpet.
25.Fit control cable to evaporator flap operating rod
using new clip. Secure outer cable.
26.Connect water valve vacuum switch pipe and
thermostat leads.
27.Fit air control flap solenoid to side of
heater/cooler unit.
28.Reconnect heater matrix hoses.
29.Connect high pressure pipe to evaporator.
30.Connect low pressure pipe and fit insulation
cover.
31.Evacuate and recharge air conditioning system
See Adjustment, Refrigerant recovery,
recycling, recharging.
32.Reconnect battery.

82AIR CONDITIONING
18
REPAIR RESISTOR, BLOWER MOTOR - LH DRIVE
Service repair no - 82.20.26
Remove
1.Remove multi-plug from resistor.
2.Remove blower motor relay from connecting
block to gain access to fixing screw.
3.Remove screw and release relay connector
block. Retain relay in connector block.
4.Remove screw and detach air conditioning 30
amp fuse bracket from resistor.
5.Lift resistor unit from top cover.
Refit
6.Locate resistor unit in top cover.
7.Fit fuse bracket.
8.Fit blower motor relay connector block and relay.
9.Fit resistor multi-plug.RESISTOR, BLOWER MOTOR - RH DRIVE
Service repair no - 82.20.26
Remove
1.Remove multi-plugs from resistor.
2.Remove 2 screws securing resistor to wing
mounted block.
3.Withdraw resistor unit.
Refit
4.Secure resistor to mounting block.
5.Fit resistor multi-plugs.

ELECTRICAL
5
DESCRIPTION AND OPERATION REV: 05/99 ALARM SYSTEM OPERATION
Arming alarm
To arm the alarm, aim handset at vehicle and press
the RH button (Padlock symbol). Provided all doors
and or apertures are closed, the direction indicator
lamps will flash three times to confirm that the alarm is
armed. All security features previously described will
be active.
Once armed, the alarm will sound if a door or the
bonnet is opened, or if movement is detected inside
the vehicle.
Disarming alarm
Within range of the vehicle, briefly press the LH
(Plain) button on the handset; the direction indicator
lamps will flash once to indicate that the alarm has
been disarmed and the engine re-mobilised.
NOTE: In some territories, the interior
lamps will illuminate when the alarm is
disarmed.
If the direction indicators fail to flash when the
alarm is armed:
This indicates that a door or the bonnet is not fully
closed, in which case the alarm will be partially armed
and engine immobilised, but interior protection will not
be active.
Once the open door or bonnet is closed, the direction
indicators will flash three times and the alarm will fully
arm as described previously.
If the alarm sounds:
The vehicle horn and alarm sounder will operate
continuously for 30 seconds when the alarm is
triggered. The horn and alarm sounder can be
triggered up to three times.
To silence the alarm, press either handset button. If
the handset is inoperative, the alarm can only be
disarmed by entering the emergency key access
code, seeEngine immobilisation override.Anti-theft alarm indicator light
A RED indicator light on the instrument panel
indicates the status of the alarm system. When the
alarm is armed successfully, the light flashes rapidly.
After 10 seconds, the light adjusts to a slower
frequency and continues flashing as an anti-theft
deterrent.
If the light fails to illuminate during the rapid flash
phase, this indicates a 'mislock' (door or the bonnet
not fully closed or key in starter switch). If this occurs,
the indicator light will still flash at slower frequency as
an anti-theft deterrent.
The indicator light will illuminate continuously under
the following conditions:
1.Alarm system armed and immobilised with
ignition 'on' or driver's door open.
2.Engine immobilised with ignition 'on' or driver's
door open.
Interior protection
Interior protection is activated automatically when the
alarm system is armed; twin sensors inside the
vehicle monitor interior space and will activate the
alarm if an intrusion is detected.
However, if passengers or animals are to be left inside
the vehicle, or if a window or sunroof is to be left
open, the alarm must be armed with the interior
protection DISABLED as follows:
To disable interior protection:
1.Open the driver's door.
2.Use the handset to arm the alarm in normal way.
3.Close the driver's door (the direction indicator
lamps will flash three times and the anti-theft
indicator light commences flashing rapidly). The
alarm system is now armed with the interior
protection disabled.
NOTE: Interior protection will not operate
until 15 seconds after the alarm is set.

86ELECTRICAL
12
DESCRIPTION AND OPERATION VEHICLE ALARM SYSTEM BUILT-IN TEST
NOTE: The handset should be detached
from the key to allow perimetric testing of
the alarm system. The system will
automatically switch to volumetric testing if the
handset is in close proximity to the starter switch.
The built-in test procedure can be accessed providing
the following conditions exist:
Alarm disarmed.
Ignition 'off'.
Doors unlocked.
Bonnet closed.
With assistance, the test mode can be entered by
completing the following instructions within 5 seconds:
1.Open bonnet.
2.Turn starter switch 'on'.
3.Open driver's door (far enough to activate door
switch).
4.Turn starter switch 'off'.
5.Turn starter switch 'on'.
If the test mode has been correctly accessed, the
alarm sounder/horn will operate briefly and the
anti-theft alarm indicator and direction indicator lamps
will flash.
Perimetric tests
The anti-theft alarm indicator light and direction
indicator lamps will flash when:
1.Door switches are activated.
2.The bonnet is opened.
3.Key switches are activated.Volumetric tests
Press the LH (unlock) button or move the handset
close to the starter switch to disable perimetric testing
and enable volumetric testing. If movement is
detected within the vehicle by the ultrasonic sensor
the anti-theft alarm indicator and direction indicator
lamps will illuminate.
NOTE: Exit the anti-theft alarm built-in test
by turning the starter switch to the 'off'
position.
If the previously described conditions are not achieved
during the built-in test procedure, this would indicate a
fault in the alarm system. Before undertaking detailed
fault diagnosis procedures, first make visual checks of
components such as a faulty door switch or blown
alarm system fuse.