1996 FORD WINDSTAR light

130
[SC02100(ALL)02/95]
To indicate a lane change to the right, push the turn signal
lever up slightly (without latching) and hold it in position. To
indicate a lane change to the left, pull the turn signal lever
down slightly (without latching) and hold it in position. The
lever will return to the OFF position when you release it.
*
[SC02200(ALL)05/94]
If the turn indicator light in the instrument panel does not
illuminate or remains on (does not flash) when you signal a
turn, the turn signaling system is malfunctioning. Have this
condition corrected as soon as possible, and use the accepted
hand signals until the turn signal system is repaired.
%*
[SC02220(ALL)03/95]
High Beams
*
[SC02226(ALL)01/93]
To turn on the high beams, turn the headlamps on and push
the turn signal lever away from you until it latches. When the
high beams are on, the high beam indicator light on the
instrument panel is illuminated.
*
[SC02230(ALL)01/93]
To return to the low beam setting, pull the turn signal lever
toward you until it latches back into the neutral position. The
high beam indicator light turns off.
*
[SC02235(ALL)11/93]
7-1/2 pica art:0040086-D
High beam and flash-to-pass operation
%*
[SC02700(ALL)05/95]
Flashing the Lights
*
[SC02800(ALL)01/93]
To flash the headlamps, pull the turn signal lever toward you
for a moment and then release it. The high beam headlamps
will flash whether the headlamps are on or off.
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

Steering Column Controls
131
%*
[SC03100(ALL)03/95]
Windshield Wipers and Washer
%*
[SC03200(ALL)03/95]
Variable Interval Wipers
[SC03300(ALL)11/93]
Your vehicle has wipers that operate at varying intervals. For
example, you can set the interval so they wipe less often in
light rain or more often in heavier rain. The wiper delays range
from about 1.5 to 20 seconds.
*
[SC03400(ALL)09/93]
10-1/2 pica art:0040087-E
Variable interval wiper control
*
[SC03500(ALL)01/93]
To set the interval wipers, rotate the knob at the end of the turn
signal lever to the most effective interval. The farther the knob
is from the OFF position, the faster the wipers move.
[SC03510(ALL)12/93]
Speed Dependent Wipers
[SC03520(ALL)01/95]
This feature compensates for the extra moisture that
accumulates on your windshield at higher speeds during rain.
At higher speeds, the Speed Dependent feature shortens the
delay between wipes when you use the variable interval wipers.
Delay will automatically adjust at speeds between 10 and
65 mph (16 and 105 km/h).
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

140
%*
[SC09400(ALL)01/95]
Resetting the Speed Control
*
[SC09410(ALL)03/95]
To reset the speed control to alower speed, use one of the
following procedures:
*
[SC09415(ALL)03/95]
n
COASTÐ Press and hold the COAST switch. Release the
switch when the vehicle slows down to the desired speed.
*
[SC09420(ALL)03/95]
n
Lightly tap the brake pedal. When the vehicle attains the
desired speed, press the SET ACCEL switch and release it
immediately.
[SC09425(ALL)04/95]
n
TAP-DOWNÐ Press and then quickly release the COAST
switch. Each time you ªtapº the switch, the set speed will
decrease by 1 mph (1.6 km/h). Multiple taps will cause the
set speed to decrease in increments of 1 mph (1.6 km/h).
For example, if the current set speed is 60 mph (97 km/h) 5
taps of the COAST switch will decrease the vehicle speed
and SET it at 55 mph (88 km/h).
*
[SC09430(ALL)04/95]
If vehicle speed is reduced below 30 mph (50 km/h) by any of
the above methods, then you must manually accelerate to a
speed over 30 mph (50 km/h) and reset the system.
*
[SC09435(ALL)03/95]
To reset the speed control toa higher speed, follow one of
these procedures:
*
[SC09440(ALL)03/95]
n
ACCELÐ Press and hold the SET ACCEL switch. Release
the switch when the vehicle has accelerated to the desired
speed.
*
[SC09445(ALL)03/95]
n
Depress the accelerator pedal. When the vehicle attains the
desired speed, press the SET ACCEL switch and release it
immediately.
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

Steering Column Controls
141
[SC09450(ALL)04/95]
n
TAP-UPÐ Press and then quickly release the SET ACCEL
switch. Each time you ªtapº the switch, the set speed will
increase by 1 mph (1.6 km/h). Multiple taps will cause the
set speed to increase in increments of 1 mph (1.6 km/h). For
example, if the current set speed is 55 mph (88 km/h), five
taps of the SET ACCEL switch will increase the vehicle
speed and set it at 60 mph (97 km/h).
[SC10525(ALL)04/95]
To Cancel or Turn Off Speed Control
[SC10530(ALL)05/95]
The speed control can be cancelled at any time by depressing
the brake pedal slightly. After cancelling, you can return to the
speed you set by pressing the RESUME switch, or set a new
speed by pressing the SET ACCEL or COAST switch.
[SC10550(ALL)03/94]
Speed control can also be cancelled when you press the OFF
switch. The speed control system will remain off until you press
the ON switch and reset the speed control.
*
[SC10700(ALL)04/95]
In addition, the speed control is turned off each time you turn
the vehicle off.
%*
[SC10900(ALL)03/95]
Resuming a Set Speed
*
[SC11000(ALL)07/94]
If you press the brake pedal, the speed control is cancelled. You
can return to the speed you set by using the RSM switch, as
long as you did not press the OFF switch.
*
[SC11200(ALL)05/95]
To resume the speed you had before, you must be driving at
least 30 mph (50 km/h).
*
[SC11300(ALL)11/94]
Press and release the RESUME switch. Your vehicle gradually
returns to the previously set speed and then maintains it.
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

142
%[SC11400(ALL)05/95]
Speed Control Light (Electronic Cluster Only)
*
[SC11500(ALL)03/95]
This light comes on when you turn on the speed control system
and set the speed. The light will be on whenever the speed
control is set, even if you override the set speed by pressing the
accelerator pedal or by pressing the coast button. The light will
go off when the brakes are used or the speed control system is
turned off.
[SC11600(ALL)11/93]
This light comes on briefly during the display self-test every
time you turn your ignition key to the ON position. The light
will go off when the key is turned to the START position. The
light should stay off when the self-test is done.
*
[SC11700(ALL)05/95]
This light does not indicate any problems with the speed control
system, but is a convenience to tell you when the speed control
system is actively maintaining a set speed.
File:wnscs.ex
Update:Tue Mar 19 08:22:27 1996

148
[FV04900(ALL)10/93]
13-1/2 pica
art:0050107-A
The keyless entry system keypad
[FV05110(ALL)04/95]
When you bought your vehicle, you were given a computer
code that operates the system for your vehicle. For your
convenience, we have duplicated this code in two places.
*
[FV05120(ALL)02/95]
The code is:
*
[FV05130(ALL)02/95]
n
on your owner's wallet card found in the glove compartment
*
[FV05145(ALL)02/95]
n
taped to the computer module
[FV05160(ALL)04/95]
When you use the keyless entry system, the illuminated entry
system turns on the interior lights for 25 seconds and the
buttons on the keypad light up for five seconds.
*
[FV05170(ALL)01/93]
Do not push the keypad buttons with a key, ball-point pen,
pencil, or any other hard object since they could damage the
buttons.
%*
[FV05200(ALL)02/95]
Using the Keyless Entry System
*
[FV05300(ALL)02/95]
To operate the Keyless Entry System, you must be familiar with
the ªpersonal codeº and the ªpermanent code.º The personal
code is a code number that you select that is easy for you to
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996

150
*
[FV06901(ALL)02/95]
To erase your personal code:
*
[FV07001(ALL)02/95]1.
Enter the original permanent code.
[FV07101(ALL)04/95]2.
Press the 1/2 button within five seconds of step #1.
*
[FV07201(ALL)02/95]3.
Wait six seconds.
[FV07250(ALL)11/93]4.
The keyless entry system automatically erases your personal
code. The system will now only respond to the permanent
code.
[FV07270(ALL)10/93]
Do not set a code that presents the numbers in sequential order,
such as 1/2, 3/4, 5/6, 7/8, 9/0. Studies show that people who
idly press the buttons usually press a sequential pattern. Also,
do not select a code that uses the same button five times.
Thieves can easily figure out these types of codes.
%*
[FV07300(ALL)01/93]
Unlocking the Doors with the Keyless Entry System
[FV07401(ALL)05/95]
You must unlock the driver's door before you unlock any of the
other doors. If you let more than five seconds pass between
pressing numbers, the system shuts down and you have to
enter the code again. The system has shut down if the keypad
light is out. If the keyless entry system does not work properly,
use the key or Remote Entry transmitter(s) to lock and unlock
the doors or liftgate until the system can be serviced.
[FV07501(ALL)02/95]1.
To unlock the driver's door, enter the code. All codes have 5
numbers. After you press the fifth number, the driver's door
unlocks.
[FV07601(ALL)06/94]2.
To unlock the passenger's door, sliding door and liftgate,
press 3/4 within five seconds of step #1, or re-enter the code
to open the driver's door then press 3/4.
*
[FV07701(ALL)02/95]
Locking the doors with the keyless entry system
*
[FV07801(ALL)03/94]
Along with unlocking your doors, you can use the keyless entry
system to lock the doors.
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996

Features
151
[FV07901(ALL)06/94]
To lock all of the doors at the same time, press the 7/8 and 9/0
buttons at the same time. It is not necessary to first enter the
keypad code. This will also arm your Ford anti-theft system.
%*
[FV09301(ALL)08/94]
Battery Saver
[FV09302(ALL)06/94]
When the ignition switch is turned to OFF, the vehicle will turn
off battery voltage to the interior lamps after 45 minutes. (The
exterior lamps are not affected.) The purpose is to minimize
extended battery drain if the lights have inadvertently been left
on or if a door or the glove box is not completely closed.
However, the timer will be immediately reset to another 45
minutes if any of the following occurs:
[FV09304(ALL)11/93]
n
any door is open or closed
[FV09305(ALL)11/93]
n
the front door handle is lifted (for Illuminated Entry only)
[FV09306(ALL)11/93]
n
taking the key IN or OUT of the ignition switch
[FV09307(ALL)11/93]
n
the Keyless Entry keypad is used
[FV09308(ALL)11/93]
n
the Remote Entry transmitter is activated
%*
[FV09313(ALL)02/95]
Remote Entry System (If equipped)
[FV09316(ALL)06/94]
If your vehicle has the remote entry system, you can lock and
unlock the vehicle doors without using a key. The remote entry
system also has a personal alarm feature. The buttons that
control the system are located on the hand held transmitter that
come with your vehicle.
*
[FV09318(ALL)02/95]
The system will work with up to four transmitters. Your vehicle
came with two transmitters. Additional transmitters can be
ordered from your dealer.
*
[FV09319(ALL)02/95]
The remote entry features only operate with the ignition in the
OFF position.
File:wnfvs.ex
Update:Tue Mar 19 08:21:54 1996