1996 FORD RANGER light

Instrument Panel Controls
83
*
[IP17890(ALL)05/95]
RWARNING
The Daytime Running Light (DRL) system will not
illuminate the tail lamps and parking lamps. Turn on
your headlamps at dusk. Failure to do so may result in a
collision.
%*
[IP17900(ALL)03/95]
Lighting Up the Instrument Panel and the Interior of
Your Vehicle
[IP18000(ALL)10/94]
The instrument panel lights can be turned on by turning the
headlamp knob toward either the first or second position. You
can brighten or dim the instrument panel lights by rotating the
thumb wheel.
[IP18200(ALL)03/95]
The interior lights will shut off after 25 seconds with all the
doors closed, or immediately when the ignition switch is turned
to the ON position, or if the vehicle speed is above five MPH
(8 km/h). The interior lights will turn off after 40 minutes if
any of the doors are left open. Refer toBattery Saverin the
Featuressection for more details.
[IP18500(R )11/89]
Courtesy and Dome Lamps
[IP19175(R )04/94]
The interior/courtesy lamp is automatically turned on when the
driver or passenger door is opened. Turning the thumb wheel
fully counterclockwise will operate the interior lamp when the
doors are closed.
[IP19185(R )08/94]
7-1/2 pica art:0021156-B
Interior/Courtesy lamp
File:06unipr.ex
Update:Wed May 1 13:46:22 1996

84
%*
[IP19187(ALL)04/95]
Cleaning the Interior Lamps
*
[IP19188(ALL)04/95]
Your interior dome lamps and map lamps are plastic and
should be cleaned with a mild detergent diluted in water. Rinse
them with clear water.
%*
[IP19190(R )08/94]
Combination Cargo and High-Mount Brakelamp
[IP19200(R )08/94]
The combination cargo/high-mount brakelamp is located outside
the vehicle, directly over the rear window. Use the thumb wheel
to turn on the cargo lamp and interior courtesy lights.
[IP19350(R )08/94]
7-1/2 pica art:0021157-B
Cargo/High-mount brakelamp
*
[IP19400(R )05/91]
RWARNING
Do not drive your vehicle with the cargo/courtesy light
on. Showing a white light to the rear while driving on
public roads is illegal in some places.
File:06unipr.ex
Update:Wed May 1 13:46:22 1996

Instrument Panel Controls
85
[IP19700(ALL)04/95]
Dome/Map Lamps (If equipped)
[IP19825(R )08/91]
The map lamps are located on each side of the dome light
assembly. You can turn the individual map lamps on or off by
sliding the switch to the left or right. To turn off, slide the
switch to the middle.
[IP19950(R )04/94]
7-1/2 pica art:0020895-B
Map lamps
*
[IP20300(ALL)04/95]
Clock Controls on Electronic Radios
[IP20400(ALL)10/94]
The electronic radios have a built-in clock. For complete
operating instructions, refer toElectronic Sound Systemsin this
Owner Guide.
File:06unipr.ex
Update:Wed May 1 13:46:22 1996

87
Steering Column Controls
*
[SC00400(ALL)01/95]
The controls on the steering column and wheel are designed to
give you easy access to the controls while you are driving.
%*
[SC00500(ALL)01/95]
The Turn Signal Lever
*
[SC00600(ALL)01/95]
You can use the turn signal lever on the left side of the steering
column to:
*
[SC00700(ALL)03/95]
n
operate the turn signals and cornering lamps
*
[SC00800(ALL)01/95]
n
turn the high beams on/off
*
[SC00900(ALL)05/95]
n
flash the lamps
*
[SC01000(ALL)01/95]
n
turn the windshield wipers and washer on/off
%*
[SC01100(ALL)01/95]
Turn Signals
[SC01600(ALL)07/95]
7-1/2 pica art:0090131-B
Turn signal lever and functions
*
[SC01800(ALL)11/89]
If the turn indicator light in the instrument panel does not
illuminate or remains on (doesn't flash) when you signal a turn,
the turn signaling system is malfunctioning. Have this condition
corrected as soon as possible, but make sure that you use the
accepted hand signals in the meantime.
File:07unscr.ex
Update:Wed May 1 13:46:58 1996

90
[SC05508(ALL)10/94]
7-1/2 pica art:0021255-A*
[SC05510(ALL)11/93]
OVERDRIVE OFF Lamp
[SC05512(ALL)03/95]
This lamp indicates the operating range of the transmission.
This lamp illuminates when the O/D ON/OFF button is
depressed. For additional information, refer to theWarning
Lights and Gaugeschapter.
[SC05514(ALL)07/95]
6 pica art:0021226-B%*
[SC05516(ALL)03/95]
Hazard Flasher
*
[SC05520(ALL)04/95]
The hazard flasher is used to alert other drivers to hazardous
situations.
*
[SC05527(ALL)10/94]
The flashers will flash and the high-mount brakelamp will stay
on steadily (not flash) with the brake pedal depressed.
*
[SC05530(ALL)08/95]
The flashers work whether your vehicle is running or not. The
flashers work for up to two hours when the battery is fully
charged and in good condition without draining the battery
excessively. If the flashers run for longer than two hours or if
the battery is not fully charged, the battery power can be
drained.
File:07unscr.ex
Update:Wed May 1 13:46:58 1996

Steering Column Controls
91
*
[SC05540(ALL)09/93]
To use the hazard flasher:
*
[SC05550(ALL)10/92]1.
Push in the flasher button; it will pop out and the lamps will
begin to flash.
*
[SC05560(ALL)10/92]2.
To stop the flashers, push in the flasher button again.
*
[SC05562(ALL)08/95]
NOTE: The flasher button will be sticking up slightly higher
when on than when off.
[SC05590(ALL)10/94]
10-1/2 pica
art:0020079-D
Hazard flasher
File:07unscr.ex
Update:Wed May 1 13:46:58 1996

Steering Column Controls
95
*
[SC08700(ALL)08/95]
RWARNING
Do not use the speed control in heavy traffic or on roads
that are winding, slippery, or unpaved.
*
[SC08801(ALL)05/95]
In mountainous areas, at higher elevations, or when pulling a
trailer, the speed control may not be able to maintain the preset
speed with the transmission in
j(Overdrive).
*
[SC08850(ALL)06/92]
If your vehicle comes with a 5-speed manual transmission, you
may prefer to drive in 4 (Fourth) gear, in mountainous areas or
at high altitudes, to improve speed control performance.
*
[SC09275(ALL)12/91]
In order to downshift (with a manual transmission) with the
speed control operating, you must press either the brake or
clutch pedal long enough to disengage the speed control. Wait a
second before depressing the clutch again and making the shift
so that the speed control can fully return to the idle position.
*
[SC09325(ALL)05/95]
RWARNING
Do not shift the transmission into N (Neutral) with the
speed control on.
[SC09350(ALL)03/95]
To maintain a preset speed under the above conditions, with
electronically controlled transmissions Ð press the Transmission
Control Switch (TCS). The indicator light will turn on and
illuminate the words ªO/D OFF.º This will cancel ªOverdrive.º
You can press the Transmission Control Switch (TCS) on or off
at any speed. For the best fuel economy during normal driving
conditions, press the Transmission Control Switch (TCS) to turn
off the light. This allows overdrive operation.
File:07unscr.ex
Update:Wed May 1 13:46:58 1996

Steering Column Controls
97
*
[SC10250(ALL)10/94]
n
TAP-UP Ð This allows you to increase your current speed in
increments of 1 mph (1.6 km/h) by a momentary tap of the
SET-ACCEL switch. Multiple taps of the SET-ACCEL switch
will increase your vehicle speed 1 mph (1.6 km/h) for each
tap. For example, if you are currently set at 60 mph
(96 km/h) and tap the SET-ACCEL switch 5 times your
vehicle speed will increase and set at 65 mph (104 km/h).
*
[SC10300(ALL)06/95]
Turning the Speed Control Off
*
[SC10400(ALL)06/95]
You can cancel the speed control while you are driving.
[SC10550(ALL)08/94]
n
Press the OFF switch. The speed control is off. If you want
to resume speed control, press the ON switch and reset the
speed control by pressing the SET ACCEL switch.
[SC10600(ALL)06/94]
n
Press the brake or clutch pedal slightly. The speed control is
suspended, but you can reset it by pressing SET ACCEL or
return to the previous set speed with the RSM switch.
*
[SC10800(ALL)10/95]
In addition, the speed control is turned off each time you turn
the vehicle ignition off.
*
[SC11100(ALL)11/89]
Driving uphill or on a steep grade
*
[SC11200(ALL)05/95]
When the speed control is on, your vehicle may significantly
drop speed when driving uphill, especially with a heavy load. If
the speed drops more than 8 to 14 mph (15 - 25 km/h) the
automatic speed control will, by design, be canceled. You may
have to temporarily resume manual speed control while driving
up a steep grade in order to maintain the speed you desire.
[SC11300(ALL)05/95]
If the speed control ªdropped outº after your climb is
completed, the speed of your light truck can be reset with the
SET ACCEL switch, or returned to the previous set speed with
the RSM switch, as long as you are driving over 30 mph
(50 km/h).
File:07unscr.ex
Update:Wed May 1 13:46:58 1996