1996 FORD RANGER light

Electronic Sound Systems
143
*
[AS29954(ALL)08/95]
If the sound skips:
*
[AS29955(ALL)08/95]
n
Badly scratched discs or extremely rough roads will cause
the sound to skip. Skipping will not damage the disc player
or scratch the discs.
*
[AS29956(ALL)01/95]
How to take care of and clean the CD Changer and
discs
*
[AS29957(ALL)01/95]
To ensure the continued performance of your CD Changer
carefully read the following precautions:
*
[AS29958(ALL)01/95]
n
Always handle a disc by the edge. Never touch the playing
surface.
[AS29959(ALL)06/95]
n
Before playing, inspect all discs for any contamination. If
needed, clean discs with an approved disc cleaner, such as
the Discwasher Compact Disc Cleaner or the Allsop 3
Compact Disc Cleaner, by wiping from the center out to the
edges. Do not use a circular motion to clean.
*
[AS29960(ALL)08/95]
n
Do not clean discs with solvents such as benzine, thinner,
commercially available cleaners or antistatic spray intended
for analog records.
*
[AS29961(ALL)01/95]
n
Do not expose the discs to direct sunlight or heat sources for
an extended period of time.
*
[AS29962(ALL)01/95]
n
Do not insert more than one disc into each disc slot of the
disc magazine. Doing so may damage the discs, disc
magazine or the disc changer.
*
[AS29963(ALL)01/95]
n
Do not insert anything other than discs into the disc
magazine.
*
[AS29964(ALL)05/95]
RWARNING
The laser beam used in the compact disc player is
harmful to the eyes. Do not attempt to disassemble the
case.
File:09unasr.ex
Update:Wed May 1 13:49:43 1996

Electronic Sound Systems
149
*
[AS30130(ALL)10/95]
NOTE: Illuminated bars in the display show relative levels of
bass and treble, and positions of speaker balance and
fader functions (left to right, front to rear).
%*
[AS30135(R )08/95]
Using the Controls of Your Cassette Tape Player
*
[AS30140(R )09/95]
NOTE: Radio power must be on to use the cassette tape
player or eject a tape.
*
[AS30145(R )08/95]
How to insert a tape
*
[AS30150(R )09/94]
Your cassette tape player is equipped with power loading. Once
you insert a tape and push slightly (with theopen edge to the
right), the loading mechanism draws the tape the rest of the
way in and play will begin after a momentary tape tightening
process.
*
[AS30155(R )09/95]
NOTE: A cassette tape can be loaded and stored with the
ignition and radio power off.
*
[AS30165(R )08/95]
How to locate a desired track on the tape
*
[AS30170(R )09/94]
There are four ways to quickly locate a desired selection on the
tape. You can use the fast forward, rewind, ºSEEKª, or ºSCANª
function. Following are brief descriptions of each.
*
[AS30175(R )09/95]
n
Fast forwarding the tape
*
[AS30180(R )01/95]
To fast forward the tape, press the ºFFª button. The radio
will begin playing until fast forward is manually stopped (by
pushing the ºTAPEª button) or the end of the tape is
reached.
*
[AS30185(R )01/95]
At the end of the tape, the direction automatically reverses
and plays the other side of the tape.
*
[AS30190(R )08/95]
n
Rewinding the tape
*
[AS30195(R )01/95]
To rewind the tape, press the ºREWª button. The radio will
begin playing until rewind is manually stopped (by pushing
the ºTAPEª button) or the beginning of the tape is reached.
File:09unasr.ex
Update:Wed May 1 13:49:43 1996

Electronic Sound Systems
151
*
[AS30260(R )04/95]
Push thekbutton to activate Dolby B Noise Reduction. Push
again to deactivate.
*
[AS30345(R )08/95]
Tips on Caring for the Cassette Player and Tapes
*
[AS30350(R )08/95]
In order to keep your cassette tape player performing the way it
was meant to, read and follow these simple precautions:
*
[AS30355(R )08/95]
n
Using a Ford Cassette Cleaning Cartridge to clean the tape
player head after 10-12 hours of play will help maintain the
best playback sound and proper tape operation.
*
[AS30360(R )08/95]
n
Only cassettes that are 90 minutes long or less should be
used. Tapes longer than 90 minutes are thinner and subject
to breakage or may jam the tape player mechanism.
*
[AS30365(R )08/95]
n
Protect cassettes from exposure to direct sunlight, high
humidity and extreme heat or cold. If they are exposed to
extreme conditions, allow them to reach a moderate
temperature before playing.
*
[AS30370(R )08/95]
n
If a tape is loose inside the cassette, tighten it before playing
by putting your finger or a pencil into one of the holes and
turning the hub until the tape is tight.
*
[AS30375(R )08/95]
n
Loose labels on cassette tapes can become lodged in the
mechanism. Remove any loose label material before inserting
cassette.
*
[AS30380(R )08/95]
n
Do not leave a tape in the cassette tape player. High heat in
the vehicle can cause the cassette to warp.
%*
[AS30401(ALL)08/95]
Clock Operation
*
[AS30411(ALL)08/95]
How to view the clock mode
[AS30421(ALL)09/94]
Press the ºCLKª button to display time. The time will continue
to be displayed until a radio or tape function is chosen. After
approximately 10 seconds, the time will again appear in the
display. To display radio or tape information only, press the
ºCLKª button a second time.
File:09unasr.ex
Update:Wed May 1 13:49:43 1996

Electronic Sound Systems
153
*
[AS36000(ALL)08/95]
When the radio waves are reflected off objects or structures, the
reflected signal cancels the normal signal, causing the antenna to
pick up noise and distortion. Cancellation effects are most
prominent in metropolitan areas, but also can become quite
severe in hilly terrain and depressed roadways.
*
[AS36100(ALL)08/95]
To minimize these conditions, a stereo/mono blend circuit has
been incorporated into this system. This feature automatically
switches a weak stereo signal to a clearer monaural signal,
which improves the quality of reception.
*
[AS36200(ALL)08/95]
Several sources of static are normal conditions on AM
frequencies. These can be caused by power lines, electric fences,
traffic lights and thunderstorms.
*
[AS36300(ALL)08/95]
Another reception phenomenon isStrong Signal Capture and
Overload. This can occur when listening to a weak station and
when passing another broadcast tower. The close station may
capture the more distant station, although the displayed
frequency does not change. While passing the tower, the station
may switch back and forth a few times before returning to the
original station.
*
[AS36400(ALL)08/95]
When several broadcast towers are present (common in
metropolitan areas) several stations may overload the receiver,
resulting in considerable station changing, mixing and
distortion.
*
[AS36500(ALL)08/95]
Automatic gain control circuitry for both AM and FM bands has
been incorporated into this system to reduce strong signal
capture and overload.
File:09unasr.ex
Update:Wed May 1 13:49:43 1996

155
Driving Your Ranger
*
[DR00350(ALL)06/95]
Procedures for driving your vehicle will vary depending on
which type of transmission your vehicle has.
[DR00450(R )10/94]
n
an Automatic Overdrive Transmission 4R44E/4R55E
*
[DR00600(ALL)06/95]
n
a manual transmission
[DR05700(ALL)06/95]
Automatic Transmission Operation
(4R44E/4R55E)
*
[DR08715(ALL)08/95]
The 4R44E and 4R55E transmissions are electronically controlled
four speed overdrive automatic transmissions with lockup
torque converter. Transmission operation is controlled by the
Powertrain Control Module (PCM).
*
[DR08720(ALL)08/95]
The PCM will automatically adjust transmission operation to
make up for varying conditions. Several sensors located on the
engine and transmission such as throttle position, engine speed,
vehicle speed and transmission temperature are used by the
PCM to shift the transmission into a higher or lower gear when
required for the best performance and fuel economy. For
example, you may notice that the transmission will upshift to a
higher gear more quickly when the vehicle has not reached
normal operating temperature.
*
[DR08730(ALL)08/95]
The PCM also controls the transmission's Torque Converter
Clutch (TCC) to further raise vehicle performance and fuel
economy. The TCC will engage when the transmission operating
temperature and other conditions determined by the PCM have
been met. Engagement of the clutch may be noted as a decrease
in engine speed.
[DR08740(ALL)03/95]
To help in troubleshooting, the PCM continually performs
self-tests on the electronic control system and, if any faults are
detected, stores them in memory. The Overdrive Off Indicator
Light (O/D OFF), which is located on the instrument cluster,
may flash steadily if a malfunction has been detected. If the
Overdrive Off Indicator Light is flashing, contact your Ford
dealer as soon as possible. If this condition persists, damage to
the transmission could occur.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

158
*
[DR09350(ALL)01/95]
N (Neutral)
*
[DR09375(ALL)01/95]
With the gearshift in the N (Neutral) position, the vehicle can be
started and is free to roll. Hold the brake pedal down while in
this position.
%*
[DR09400(ALL)01/95]
Driving
%*
[DR09500(ALL)04/95]
When to use
j(Overdrive)
*
[DR09600(ALL)04/95]
This is the normal driving position. As the vehicle picks up
speed, automatic upshifts to second, third and fourth gears will
occur when
jOverdrive is chosen on the selector and the
transmission control switch has not been pressed. The
transmission will shift into the correct gear when the right
speed is achieved, for the accelerator pedal position you have
chosen.
*
[DR09700(ALL)03/94]
When to use Drive
[DR09800(ALL)06/95]
You will note there is not a drive position on your gearshift
indicator. However, you will find a transmission control switch
labeled O/D ON/OFF located on the end of the gearshift lever.
Press this switch and the O/D OFF indicator light will
illuminate on the instrument cluster. With overdrive cancelled
and the O/D OFF indicator light illuminated, the transmission
will operate in gears one through three. This is useful if you
experience frequent downshift/upshift conditions, when
operating with a heavy load or in hilly terrain, or if additional
engine braking is useful. However, shift back to
j(Overdrive)
whenever practical for optimum powertrain cooling and fuel
economy. This can be accomplished by pushing the transmission
control switch again, to cancel the O/D OFF control and light.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

Driving Your Ranger
159
[DR09850(ALL)01/95]
quarter page
art:0021255-A
Transmission control switch (located on the end of the gearshift lever)
*
[DR09900(ALL)05/95]
To return the transmission to the normal
jOverdrive
operation, press the transmission control switch again. The
Transmission Control Indicator Light will not be illuminated
when Overdrive operation resumes. This switch may be used to
select O/D ON or O/D OFF any time the vehicle is being
driven.
*
[DR09950(ALL)05/94]
When starting your vehicle, the overdrive system will
automatically be in the normal overdrive mode.
*
[DR10100(ALL)01/95]
When to use 2 (Second)
*
[DR10200(ALL)01/95]
Use 2 (Second) to start-up on slippery roads or to provide
additional engine braking on downgrades. This position
provides 2 (Second) gear operation only.
*
[DR10300(ALL)01/95]
When to use 1 (Low)
*
[DR10400(ALL)04/95]
Use 1 (Low) to provide maximum engine braking on steep
downgrades. Upshifts from 1 (Low) can be made by manually
shifting to 2 (Second) or
j(Overdrive). Selection of 1 (Low)
gear provides only low gear operation from start-up. Selection
of 1 (Low) while at higher speeds provides a shift to second
gear, and a shift to first gear will occur after the vehicle
decelerates to the proper speed.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

Driving Your Ranger
169
[DR16370(R )07/94]
4WD system indicator lights
[DR16401(R )10/94]
A 4WD light and a 4WD LOW light are located in the
instrument cluster.
[DR16430(R )10/94]
n
2H position Ð Neither the 4WD or the 4WD LOW lights are
lit.
[DR16460(R )07/94]
n
4H position Ð Only the 4WD light is lit.
[DR16490(R )10/94]
n
N position Ð Neither the 4WD or 4WD LOW lights are lit.
[DR16520(R )10/94]
n
4L position Ð Both the 4WD and the 4WD LOW lights are
lit.
*
[DR17060(R )06/94]
To shift from 2H to 4H:
*
[DR17090(R )06/94]
Stop the vehicle and engage the manual locking hubs by
turning both hub lock selector knobs clockwise to the LOCK
position. Move the transfer case shift lever straight back to the
4H position. After both hubs have been turned to the LOCK
position, shifts between 2H and 4H (or 4H to 2H) may take
place at any speed.
[DR17120(R )06/94]
10-1/2 pica
art:0021182-A
Locking hub positions
[DR17150(R )09/95]
NOTE: Do not drive the vehicle in 4H or 4L with the manual
locking hubs in the FREE position.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996