1996 FORD EXPLORER ECO mode

234
*
[AS29905(ALL)04/95]
Operating the CD Compression feature
[AS29910(ALL)04/94]
Because of the wide dynamic range of Ford’s 6-CD Changer
System, soft passages may be difficult to hear under certain
driving conditions while maintaining a reasonable volume level
in the louder passages. The compression feature will bring these
soft and loud passages closer together for a more consistent
listening level.
*
[AS29915(ALL)01/95]
To turn the compression on, press the“COMPRESS”/#5 button.
When the compression feature is activated, the display will
indicate“C”.
*
[AS29916(ALL)02/95]
Operating the Shuffle feature
*
[AS29917(ALL)01/95]
While in the CD mode, pressing the“SHUFFLE”/#6 button will
randomly select a track from the disc currently being played.
The display will indicate“SHF”followed by the disc and track
number (dd-tt).
*
[AS29918(ALL)01/95]
The CD Changer will continue to randomly select tracks for
play until the shuffle feature is turned off by pressing the
“SHUFFLE”button a second time.
*
[AS29919(ALL)02/95]
HowtostopCDplay
*
[AS29920(ALL)01/95]
While in the CD mode, press the“AM/FM”button to stop CD
play and resume radio play. Also, loading a cassette into the
cassette deck will stop CD play and begin cassette play.
*
[AS29935(ALL)02/95]
CD Error Messages
*
[AS29936(ALL)01/95]
Your system is equipped to diagnose certain problems you may
experience. The error codes are:
*
[AS29937(ALL)01/95]
—CD E1—Mechanism error.
*
[AS29938(ALL)01/95]
—CD E2—Focus error.
*
[AS29939(ALL)01/95]
—BAD CD—Disc unreadable.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

Electronic Sound Systems
239
*
[AS30010(ALL)09/95]


Using the”TUNE“function
*
[AS30015(ALL)03/95]
You can change the frequency up or down one increment at
a time by pressing and releasing either the left (
b) or right
(
a) side of the”TUNE“button.
*
[AS30020(ALL)08/95]
Manual tuning adjusts your radio to any allowable broadcast
frequency, whether or not a station is present on that
frequency. (SeeAll About Radio Frequenciesin this section.)
*
[AS30025(ALL)08/95]


Using the”SEEK“function
*
[AS30030(ALL)09/95]
This feature on your radio allows you to automatically select
listenable stations up or down the frequency band. Press the
right (
a) side of the”SEEK“button to select the next
listenable station up the frequency band. Press the left (
b)
side of the button to select the next listenable station down
the frequency band. By holding the button down, listenable
stations can be passed over to reach the desired station.
*
[AS30035(ALL)01/95]


Using the”SCAN“function
*
[AS30040(ALL)04/95]
Pressing the”SCAN“button will begin the scan mode up
the frequency band, stopping on each listenable station for
approximately five seconds.
*
[AS30045(ALL)02/95]
To stop the scan mode on the presently sampled station,
press the”SCAN“button again.
*
[AS30050(ALL)08/95]


Setting the Station Memory Preset buttons
*
[AS30055(ALL)02/95]
Your radio is equipped with 6 station memory buttons.
These buttons can be used to select up to 6 preset AM
stations and 12 FM stations (6 in FM1 and 6 in FM2).
*
[AS30060(ALL)08/95]
Follow the easy steps below to set these buttons to the desired
frequencies:
*
[AS30065(ALL)08/95]1.
Select a band, then select a frequency.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

Electronic Sound Systems
241
%*
[AS30401(ALL)08/95]
Clock Operation
*
[AS30411(ALL)08/95]
How to view the clock mode
[AS30421(ALL)09/94]
Press the”CLK“button to display time. The time will continue
to be displayed until a radio or tape function is chosen. After
approximately 10 seconds, the time will again appear in the
display. To display radio or tape information only, press the
”CLK“button a second time.
[AS30431(ALL)09/95]
NOTE: The clock can be displayed or set whether the ignition
is on or off.
*
[AS30441(ALL)08/95]
How to set the clock
*
[AS30451(ALL)08/95]1.
Turn the radio on.
[AS30461(ALL)04/95]2.
Press and hold the”CLK“button, press the right (
a) side of
the”SEEK“button to increase hours. Press the left (
b) side
of the button to decrease hours. Press the right (
a) side of
the”TUNE“button to increase minutes. Press the left (
b)
side of the button to decrease minutes.
*
[AS30471(ALL)09/95]
NOTE: The clock displays 12-hour time with no AM/PM
indications.
%*
[AS35200(ALL)08/95]
Common Radio Reception Conditions
*
[AS35300(ALL)08/95]
Several conditions prevent FM reception from being completely
clear and noise-free, such as the following:
*
[AS35400(ALL)08/95]1.
Distance/Strength
*
[AS35500(ALL)08/95]
The strength of the FM signal is directly related to the distance
the signal must travel. The listenable range of an average FM
signal is approximately 25 miles (40 kilometers). Beyond this
distance, the radio is operating in a fringe area and the signal
becomes weaker.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

Driving Your Explorer
249
[DR09850(ALL)01/95]
quarter page
art:0021255-A
Transmission control switch (located on the end of the gearshift lever)
*
[DR09900(ALL)05/95]
To return the transmission to the normal
jOverdrive
operation, press the transmission control switch again. The
Transmission Control Indicator Light will not be illuminated
when Overdrive operation resumes. This switch may be used to
select O/D ON or O/D OFF any time the vehicle is being
driven.
*
[DR09950(ALL)05/94]
When starting your vehicle, the overdrive system will
automatically be in the normal overdrive mode.
*
[DR10100(ALL)01/95]
When to use 2 (Second)
*
[DR10200(ALL)01/95]
Use 2 (Second) to start-up on slippery roads or to provide
additional engine braking on downgrades. This position
provides 2 (Second) gear operation only.
*
[DR10300(ALL)01/95]
When to use 1 (Low)
*
[DR10400(ALL)04/95]
Use 1 (Low) to provide maximum engine braking on steep
downgrades. Upshifts from 1 (Low) can be made by manually
shifting to 2 (Second) or
j(Overdrive). Selection of 1 (Low)
gear provides only low gear operation from start-up. Selection
of 1 (Low) while at higher speeds provides a shift to second
gear, and a shift to first gear will occur after the vehicle
decelerates to the proper speed.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

256
%*
[DR16101(ALL)03/95]
Four-Wheel Drive (4WD) System
(If equipped)
[DR16130(ALL)10/94]
When you select the 4WD mode, your vehicle uses all four
wheels to power itself. This increases traction, enabling you to
drive your 4x4 over terrain and road conditions not travelled
normally by two-wheel drive vehicles.
*
[DR16160(ALL)10/94]
Power is supplied to all four wheels through a transfer case that
allows you to select four-wheel drive when necessary. Methods
for engaging and disengaging 4WD and low range will depend
on which system your vehicle has.
[DR17585( X)01/95]
4WD Systems Ð Control Trac
[DR17615( X)01/95]
The Control Trac 4WD system functions in three modes. In
two-wheel drive mode, power is delivered only to the rear axle.
The 4WD AUTO position provides four-wheel drive with full
power delivered to the rear axle, and to the front axle as
required for increased traction. The 4WD LOW position
provides four-wheel drive with full power delivered to the front
and rear axles when above average power is required at
reduced speeds.
[DR17645( X)01/95]
Four-wheel drive operation (4WD LOW) on dry pavement is not
recommended. Operating the vehicle in 4WD LOW on dry
pavement will increase noise, vibration, tire wear, and decrease
fuel economy.
[DR17690( X)08/94]
Control Trac system indicator lights
[DR17735( X)03/95]
A 4WD indicator light and a 4WD LOW indicator light are
located in the instrument cluster. If either light flashes, take
your vehicle in for service.
[DR17750(ALL)01/95]
n
Two-Wheel Drive mode Ð Neither the 4WD nor the 4WD
LOW lights are lit.
[DR17790( X)1/96]
n
4WD Auto mode Ð Only the 4WD light is lit.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

258
[DR18230( X)10/94]
Toshiftfrom4WDAUTOor2WDto4WDLOW:
[DR18290( X)01/95]
Stop the vehicle, depress the brake and place the automatic
transmission in N (Neutral) or depress the clutch on vehicles
with a manual transmission. Rotate the 4WD switch on the
instrument panel to 4WD LOW. Both the 4WD and 4WD LOW
lights are now lit.
[DR18293( X)06/95]
For Explorers equipped with Automatic Ride Control:
[DR18294( X)06/95]
After shifting to 4WD LOW, wait about 90 seconds. This will
improve ground clearance and off-road handling. Refer to
Automatic Ride Controlin the Features chapter.
[DR18320( X)08/94]
To shift from 4WD LOW to 4WD AUTO or 2WD:
[DR18400( X)01/95]
Stop the vehicle, depress the brake and place the automatic
transmission into N (Neutral) or depress the clutch on vehicles
with a manual transmission. Rotate the 4WD switch on the
instrument panel to 4WD AUTO or 2WD.
[DR18500(ALL)03/95]
It is not recommended to operate the vehicle in the 4WD modes
with a temporary spare. If 4WD operation is necessary, do not
operate at speeds above 10 mph or for distances above 50 miles.
Extended operation in 4WD with a temporary spare may result
in damage to drivetrain components.
[DR18600( X)12/95]
All-Wheel Drive System (If equipped)
[DR18620( X)12/95]
If your vehicle is equipped with All-Wheel Drive (AWD), power
is constantly supplied to all four wheels through a transfer case.
The AWD system is full-time and has no external controls.
[DR18630( X)12/95]
The AWD transfer case utilizes a viscous clutch that distributes
torque to the front and rear differentials (approximately 35%
front and 65% rear). The viscous clutch is filled with a
high-viscosity fluid, see
Lubricant Specifications
in the
Servicing
Your Explorer
chapter for more information.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

264
[DR22965(ALL)05/95]
Should a malfunction in the 4WABS system occur, the ABS light
on the instrument cluster will come on and stay on indicating
that the anti-lock system has been shut down and the vehicle
needs to be serviced. Normal braking is not affected unless the
brake warning light is also illuminated.
*
[DR22970(ALL)09/95]
NOTE: It is important to note that when the ABS Warning
Light is illuminated the ABS system is disabled. The
vehicle must be serviced immediately to restore the
benefits of the Anti-lock system.
*
[DR22975(ALL)09/95]
NOTE: Mobile phones or radio transmitters not installed by
Ford Motor Company may interfere with the Anti-lock
System. Should the Anti-lock system activate
unexpectedly or the Anti-lock Warning Light
illuminate after installation of such a unit, have the
installation of the unit checked.
%*
[DR23000(ALL)12/89]
If Brakes Do Not Grip Well or Pedal is ªLowº
*
[DR23250(ALL)11/89]
If during normal operation the brake pedal seems ªlowº, it may
indicate the need for a brake system inspection and/or service.
You should have your brakes checked as soon as possible.
*
[DR23300(X)07/95]
Occasional brake squeal during light to moderate stops does not
affect the function of the brake system and is normal. However,
if the squeal becomes louder or more frequent, have your
brakes inspected by your dealer or a qualified service technician.
*
[DR23400(ALL)11/89]
RWARNING
Modifications to the suspension spring rates and/or
vehicle ride height may adversely affect vehicle stopping
ability.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

Driving Your Explorer
265
*
[DR23500(ALL)07/92]
If Brakes Pull
*
[DR23600(ALL)05/95]
n
Check tire pressure.
[DR23710( X)07/95]
n
If pull occurs during the first 500 miles (800 km), make 10
moderatley fast stops from 40 mph (64 km/h). It may be
necessary to repeat this operation to properly seat new
brakes.
*
[DR23800(ALL)05/95]
If pull occurs during the first 500 miles (800 km), make 10
moderately fast stops from 40 mph (65 km/h) and then
perform the self-adjustment procedure above. It may be
necessary to repeat this operation to properly seat new brake
linings and pads.
%*
[DR24000(ALL)01/93]
Stopping Distances
*
[DR24100(ALL)11/89]
Stopping distances vary with different loads and driving
conditions. Use caution when encountering new conditions and
acquaint yourself with vehicle performance. Take full advantage
of engine braking power when slowing down.
%*
[DR24200(ALL)01/95]
Applying the Brakes
*
[DR24300(ALL)05/95]
Apply the brake pedal gradually. Use the ªsqueezeº technique
Ð push on the brake pedal with a steadily increasing force. This
allows the wheels to continue to roll while you are slowing
down, which lets you steer properly.
*
[DR24400(ALL)07/95]
Do not drive with your foot resting on the brake pedal. This
will increase your vehicle's stopping distance and may also
cause brake damage.
*
[DR24500(ALL)05/95]
RWARNING
If you are driving down a long or steep hill, shift to a
lower gear. Do not apply your brakes continuously, as
they may overheat and become less effective.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996