1996 FORD EXPLORER stop start

70
%*
[ST04800(ALL)03/95]
Fuel-Injected Engines
*
[ST04900(ALL)03/95]
When starting a fuel-injected engine,the most important thing
to remember is to avoid pressing down on the accelerator
before or during starting. Only use the accelerator when you
have problems getting your vehicle started. SeeStarting Your
Enginein this chapter for details about when to use the
accelerator while you start your vehicle.
*
[ST04950(ALL)03/95]
Starting Your Vehicle
%*
[ST05200(ALL)05/94]
Preparing to Start Your Vehicle
*
[ST05300(ALL)09/95]
RWARNING
Do not start your vehicle in a closed garage or other
enclosed area. Never sit in a stopped vehicle for more
than a short period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding Against Exhaust
Fumesin this chapter for more instructions.
*
[ST05400(ALL)01/95]
Before you start your vehicle, do the following:
*
[ST05500(ALL)08/95]1.
Make sure all occupants in the vehicle buckle their safety
belts. SeeSafety Restraintsin the Index for more details.
*
[ST05600(ALL)03/95]2.
Make sure the headlamps and other accessories are turned
off when starting.
*
[ST05700(ALL)10/94]3.
If you have an automatic transmission,make sure that the
gearshift lever is in P (Park) and the parking brake is set
before you turn the key.
*
[ST05800(ALL)03/91]4.
If you have a manual transmission,make sure that the
parking brake is fully set, push the clutch pedal to the floor,
and put the gearshift into Neutral before you turn the key.
(Remember, the starter will operate only if the clutch pedal
is pushed in all the way).
File:04unstx.ex
Update:Thu Feb 29 09:22:05 1996

72
%*
[ST06521(ALL)05/95]
For a warm engine:
*
[ST06522(ALL)04/95]
n
Do not hold the key in the START position for more than
five (5) secondsat a time. If the engine does not start within
five (5) seconds on the first try, turn the key to the OFF
position. Wait a few seconds after the starter stops, then try
again.
*
[ST06575(ALL)08/95]
Whenever you start your vehicle, release the key as soon as the
engine starts. Excessive cranking could damage the starter.
*
[ST06601(ALL)09/95]
After starting, allow the engine to idle for a few seconds before
driving away.
%*
[ST06775(ALL)04/95]
If the engine does not start after two attempts:
*
[ST06825(ALL)04/95]1.
Turn the ignition key to the OFF position.
*
[ST06851(ALL)04/95]2.
Press the accelerator all the way to the floor and hold it.
*
[ST06876(ALL)04/95]3.
Turn the ignition key to the START position.
*
[ST06900(ALL)04/95]4.
Release the ignition key when the engine starts.
*
[ST06925(ALL)04/95]5.
Release the accelerator gradually as the engine speeds up.
Then drive away in the normal manner.
*
[ST06951(ALL)04/95]
If the engine still does not start, the fuel pump shut-off switch
may have been triggered. For directions on how to reset the
switch seeFuel Pump Shut-Off Switchlater in this chapter.
%*
[ST07300(ALL)10/95]
A computer system controls the engine's idle speed. When you
start your vehicle, the engine's idle speed normally runs high.
These faster engine speeds will make your vehicle coast slightly
faster than its normal idle speed. It should, however, slow down
after a short time. If it does not, have the idle speed checked.
*
[ST07390(ALL)07/95]
If the engine idle speed does not slow down automatically, do
not allow your vehicle to idle for more than 10 minutes. Have
the vehicle checked.
File:04unstx.ex
Update:Thu Feb 29 09:22:05 1996

74
%*
[ST08175(ALL)03/95]
If the Engine Cranks but Does Not Start or
Does Not Start After a Collision
*
[ST08200(ALL)07/95]
The Fuel Pump Shut-off Switch
*
[ST08210(ALL)10/95]
If the engine cranks but does not start or does not start after a
collision, the fuel pump shut-off switch may have been
triggered. The shut-off switch is a device intended to stop the
fuel pump when your vehicle has been involved in a major jolt.
*
[ST08215(ALL)03/95]
Once the shut-off switch is triggered, you must reset the switch
by hand before you can start your vehicle.
[ST08225(ALL)03/95]
10-1/2 pica
art:0090157-A
Fuel pump shut-off switch location
*
[ST08250(ALL)05/95]
RWARNING
If you see or smell fuel, do not reset the switch or try to
start your vehicle. Have all the passengers get out of the
vehicle and call the local fire department or a towing
service.
File:04unstx.ex
Update:Thu Feb 29 09:22:05 1996

Starting Your Explorer
77
*
[ST10300(ALL)01/95]
Improve your ventilation by keeping all air inlet vents clear of
snow, leaves, and other debris.
*
[ST10400(ALL)08/95]
If the engine is idling while you are stopped in an open area
for long periods of time, open the windows at least one inch
(2.5 cm). Also, adjust the heating or air conditioning system to
bring in outside air.
[ST10650(ALL)03/95]
n
HEATING Ð Set fan speed to medium or high, the function
control knob on any position except OFF and the
temperature control knob on any desired position.
[ST10700(ALL)03/95]
n
AIR CONDITIONING Ð Set fan speed to medium or high
with the function control knob on any position (except OFF
or MAX A/C) and the temperature control knob at a
comfortable level.
File:04unstx.ex
Update:Thu Feb 29 09:22:05 1996

90
%*
[LG07500(ALL)05/94]
Engine Oil Pressure Gauge
*
[LG07601(ALL)06/93]
This gauge indicates the engine's oil pressure, not the oil level.
However, if your engine's oil level is low, it could affect the oil
pressure. With the engine running, the pointer should move into
the NORMAL band. If the pointer drops below the NORMAL
band while the engine is running, you have lost oil pressure
and continued operation will cause severe engine damage.
*
[LG07701(ALL)03/95]
If you lose engine oil pressure:
*
[LG07801(ALL)03/95]1.
Pull off the road as soon as safely possible.
*
[LG07901(ALL)03/95]2.
Turn off the engine. If you do not stop the engine as soon as
safely possible, severe engine damage could result.
*
[LG08001(ALL)02/95]3.
Check the engine's oil level, following the instructions on
checking and adding engine oil. Refer toEngine oilin the
Index. If you do not follow these instructions, you or others
could be injured. To assure an accurate reading, your vehicle
should be on level ground.
*
[LG08051(ALL)03/93]4.
If the level is low, add only as much oil as necessary before
you start the engine again. Do not overfill. Do not operate
the engine if the pointer is below the NORMAL band,
regardless of the oil level. Contact your nearest dealer for
further service actions.
[LG08150(ALL)10/94]
7-1/2 pica art:0020540-E
Engine oil pressure gauge Ð mechanical cluster with tachometer
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

118
[IP05800( X)03/95]
When in AUTOMATIC and weather conditions require heat, air
will be sent to the floor. However, a feature is included in your
EATC to prevent blowing cold air to the floor if the engine
coolant is not warm enough to allow heating. In 3 1/2 minutes
or less, the fan speed will start to increase and the air flow will
be to the floor area.
[IP05900( X)07/94]
If unusual conditions exist (i.e. window fogging, etc.), the six
manual override buttons allow you to select special air
discharge locations. A thumbwheel allows you to adjust the fan
speed to suit your needs.
*
[IP06000( X)03/95]
Temperature selection
[IP06100( X)03/95]
The RED and BLUE buttons at the upper left of the Control are
for temperature selection. The RED button will increase the set
temperature and the BLUE button will lower the set
temperature. Pressing a button and releasing it will change the
set temperature one degree. Holding either button in will
rapidly change the temperature setting in one degree increments
to either65ÊF (18ÊC)(BLUE) or85ÊF (29ÊC)(RED). Then, the set
temperature will jump 5Ê and stop at either60ÊF (16ÊC)which is
maximum cooling or90ÊF (32ÊC)which is maximum heating.
When you select60ÊF (16ÊC) or 90ÊF (32ÊC), the fanwill go to
HI speed for maximum airflow.
File:06unipx.ex
Update:Thu Feb 29 09:05:45 1996

Electronic Sound Systems
215
*
[AS05700( X)08/95]


Using the“SEEK”function with your cassette tape player
*
[AS05800( X)05/95]
While in the tape mode, push the right (
a) side of the
“SEEK”button to seek forward to the next selection on the
tape. Push the left (
b) side to restart a currently playing
tape selection.
*
[AS05900( X)01/95]


Using the“Blank Skip”function with your cassette tape
player
*
[AS06000( X)01/95]
Press the“Blank Skip”button to activate the blank skip
mode. After approximately 20 seconds of blank program, the
tape will seek forward to the next program.
*
[AS06100( X)08/95]


Using the“SCAN”function with your cassette tape player
*
[AS06200( X)01/95]
Pushing the“SCAN”button will begin the forward scan
mode on the tape currently playing, stopping on each tape
selection for approximately eight seconds.
*
[AS06300( X)01/95]
To stop the scan mode on the presently sampled tape
selection, press the“SCAN”button or the“TAPE”button.
*
[AS06400( X)08/95]


How to change the side of the tape being played
*
[AS06500( X)01/95]
The alternate side of the tape can be selected by pressing the
“SIDE 1-2”button.
*
[AS06600( X)08/95]
How to eject the tape
*
[AS06700( X)03/95]
To stop the tape and eject the cassette, press the“EJECT”
button. The tape will eject only when in the tape mode. The
cassette cannotbe ejected when the radio is playing an“AM”
or“FM”station. The system will revert to radio mode when
the cassette is ejected.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

248
%*
[DR09200(ALL)01/95]
R (Reverse)
*
[DR09300(ALL)08/95]
With the gearshift in the R (Reverse) position, the vehicle will
move backward. You should always come to a complete stop
before shifting into or out of R (Reverse).
*
[DR09350(ALL)01/95]
N (Neutral)
*
[DR09375(ALL)01/95]
With the gearshift in the N (Neutral) position, the vehicle can be
started and is free to roll. Hold the brake pedal down while in
this position.
%*
[DR09400(ALL)01/95]
Driving
%*
[DR09500(ALL)04/95]
When to use
j(Overdrive)
*
[DR09600(ALL)04/95]
This is the normal driving position. As the vehicle picks up
speed, automatic upshifts to second, third and fourth gears will
occur when
jOverdrive is chosen on the selector and the
transmission control switch has not been pressed. The
transmission will shift into the correct gear when the right
speed is achieved, for the accelerator pedal position you have
chosen.
*
[DR09700(ALL)03/94]
When to use Drive
[DR09800(ALL)06/95]
You will note there is not a drive position on your gearshift
indicator. However, you will find a transmission control switch
labeled O/D ON/OFF located on the end of the gearshift lever.
Press this switch and the O/D OFF indicator light will
illuminate on the instrument cluster. With overdrive cancelled
and the O/D OFF indicator light illuminated, the transmission
will operate in gears one through three. This is useful if you
experience frequent downshift/upshift conditions, when
operating with a heavy load or in hilly terrain, or if additional
engine braking is useful. However, shift back to
j(Overdrive)
whenever practical for optimum powertrain cooling and fuel
economy. This can be accomplished by pushing the transmission
control switch again, to cancel the O/D OFF control and light.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996