1996 FORD EXPLORER ECO mode

200
[FV62850( X)05/95]
Calibration adjustment:
*
[FV62900( X)03/93]1.
Find an open area that is free from steel structures and high
voltage lines. An open parking lot is a good example.
*
[FV63000( X)03/93]2.
Press and hold the ªMODEº button until the ªCALº
indicator appears in the display (approximately 8 seconds).
*
[FV63050( X)05/95]
NOTE: You cannot perform calibration unless the display
reads ªCAL.º
*
[FV63100( X)03/93]3.
Release the ªMODEº button.
*
[FV63300( X)03/93]4.
Once the ªCALº indicator has appeared, drive the vehicle
slowly (less than 3 mph / 5 km/h) in360Êcircles until the
ªCALº indicator turns off. This will happen within 2 to 3
complete circles.
%*
[FV63800( X)03/93]
Map lamps
*
[FV63900( X)03/93]
The map lamps are located in the overhead console. The driver
and passenger side each has its own switch.
[FV64000( X)09/95]
10-1/2 pica
art:0020975-B
Map lamps (If equipped)
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

210
%*
[AS01500( X)08/95]
How to tune radio stations
*
[AS01600( X)01/95]
There are four ways for you to tune in a particular station. You
can use the“TUNE”,“SEEK”,“SCAN”or memory buttons.
*
[AS01700( X)09/95]


Using the“TUNE”function
*
[AS01800( X)01/95]
You can change the frequency up or down one increment at
a time by pressing and releasing either the left (
b) or right
(
a) side of the“TUNE”or“TUNE DISCS”button. To
change frequencies quickly, press and hold down either the
right or left side of the button.
*
[AS01900( X)08/95]
Manual tuning adjusts your radio to any allowable broadcast
frequency, whether or not a station is present on that
frequency. (SeeAll About Radio Frequenciesin this section.)
*
[AS02000( X)08/95]


Using the“SEEK”function
*
[AS02100( X)05/95]
Press the right (
a) side of the“SEEK”button to select the
next listenable station up the frequency band. Press the left
(
b) side of the button to select the next listenable station
down the frequency band. By holding the button down,
listenable stations can be passed over to reach the desired
station.
*
[AS02200( X)01/95]


Using the“SCAN”function
*
[AS02300( X)04/95]
Pressing the“SCAN”button will begin the scan mode up
the frequency band, stopping on each listenable station for
approximately five seconds.
*
[AS02400( X)02/95]
To stop the scan mode on the presently sampled station,
press the“SCAN”button again.
*
[AS02500( X)01/95]


Setting the station MEMORY PRESET buttons
*
[AS02600( X)01/95]
Your radio is equipped with 6 station memory buttons.
These buttons can be used to select up to 6 preset AM
stations and 12 FM stations (6 in FM1 and 6 in FM2)
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

Electronic Sound Systems
215
*
[AS05700( X)08/95]


Using the“SEEK”function with your cassette tape player
*
[AS05800( X)05/95]
While in the tape mode, push the right (
a) side of the
“SEEK”button to seek forward to the next selection on the
tape. Push the left (
b) side to restart a currently playing
tape selection.
*
[AS05900( X)01/95]


Using the“Blank Skip”function with your cassette tape
player
*
[AS06000( X)01/95]
Press the“Blank Skip”button to activate the blank skip
mode. After approximately 20 seconds of blank program, the
tape will seek forward to the next program.
*
[AS06100( X)08/95]


Using the“SCAN”function with your cassette tape player
*
[AS06200( X)01/95]
Pushing the“SCAN”button will begin the forward scan
mode on the tape currently playing, stopping on each tape
selection for approximately eight seconds.
*
[AS06300( X)01/95]
To stop the scan mode on the presently sampled tape
selection, press the“SCAN”button or the“TAPE”button.
*
[AS06400( X)08/95]


How to change the side of the tape being played
*
[AS06500( X)01/95]
The alternate side of the tape can be selected by pressing the
“SIDE 1-2”button.
*
[AS06600( X)08/95]
How to eject the tape
*
[AS06700( X)03/95]
To stop the tape and eject the cassette, press the“EJECT”
button. The tape will eject only when in the tape mode. The
cassette cannotbe ejected when the radio is playing an“AM”
or“FM”station. The system will revert to radio mode when
the cassette is ejected.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

Electronic Sound Systems
219
*
[AS08200( X)08/95]


Protect cassettes from exposure to direct sunlight, high
humidity and extreme heat or cold. If they are exposed to
extreme conditions, allow them to reach a moderate
temperature before playing.
*
[AS08300( X)08/95]


If a tape is loose inside the cassette, tighten it before playing
by putting your finger or a pencil into one of the holes and
turning the hub until the tape is tight.
*
[AS08400( X)08/95]


Loose labels on cassette tapes can become lodged in the
mechanism. Remove any loose label material before inserting
a cassette.
*
[AS08500( X)08/95]


Do not leave a tape in the cassette tape player when not in
use. High heat in the vehicle can cause the cassette to warp.
%*
[AS08600( X)08/95]
Clock Operation
*
[AS08700( X)08/95]
How to view the clock mode
[AS08800( X)09/94]
Press the“CLK”button to display time. The time will continue
to be displayed until a radio or tape function is chosen. After
approximately 10 seconds, the time will again appear in the
display. To display radio or tape information only, press the
“CLK”button a second time.
[AS08900( X)09/95]
NOTE: The clock can be displayed or set whether the ignition
is on or off as long as the“CLK”button is depressed.
*
[AS09000( X)08/95]
How to set the clock
*
[AS09100( X)08/95]1.
Turn the radio on.
[AS09200( X)04/00]2.
Press and hold the“CLK”button, press the right (
a) side of
the“SEEK”button to increase hours. Press the left (
b) side
of the button to decrease hours. Press the right (
a) side of
the“TUNE”or“TUNE DISCS”button to increase minutes.
Press the left (
b) side of the button to decrease minutes.
*
[AS09300( X)09/95]
NOTE: The clock displays 12-hour time with no AM/PM
indications.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

Electronic Sound Systems
223
%*
[AS29260(ALL)08/95]
How to tune radio stations
[AS29265(ALL)10/94]
There are four ways for you to tune in a particular station. You
can use the“TUNE”,“SEEK”,“SCAN”or the memory buttons.
*
[AS29270(ALL)09/95]


Using the“TUNE”function
[AS29275(ALL)03/95]
You can change the frequency up or down one increment at
a time by pressing and releasing either the left (
b) or right
(
a) side of the“TUNE”button. To change frequencies
quickly, press and hold down either the right or left side of
the button.
*
[AS29280(ALL)08/95]
Manual tuning adjusts your radio to any allowable broadcast
frequency, whether or not a station is present on that
frequency. (SeeAll About Radio Frequenciesin this section.)
*
[AS29285(ALL)08/95]


Using the“SEEK”function
[AS29290(ALL)09/94]
This feature on your radio allows you to automatically select
listenable stations up or down the frequency band. Press the
right (
a) side of the“SEEK”button to select the next
listenable station up the frequency band. Press the left (
b)
side of the button to select the next listenable station down
the frequency band. By pressing and holding the button,
listenable stations can be passed over to reach the desired
station.
*
[AS29295(ALL)01/95]


Using the“SCAN”function
*
[AS29305(ALL)04/95]
Pressing the“SCAN”button will begin the scan mode up
the frequency band, stopping on each listenable station for
approximately five seconds.
*
[AS29310(ALL)02/95]
To stop the scan mode on the presently sampled station,
press the“SCAN”button again.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

Electronic Sound Systems
227
*
[AS29505(ALL)08/95]


Using the“SEEK”function with your cassette tape player
*
[AS29510(ALL)08/95]
While in the tape mode, push the right (
a) side of the
“SEEK”button to seek forward to the next selection on the
tape. Push the left (
b) side to seek the previous tape
selection.
*
[AS29515(ALL)08/95]


Using the“SCAN”function with your cassette tape player
*
[AS29520(ALL)01/95]
Press the“SCAN”button to begin the forward scan mode on
the tape currently playing, stopping on each tape selection
for approximately an eight-second sampling (display
indicates“SC”).
*
[AS29525(ALL)01/95]
To stop the scan mode on the presently sampled tape
selection, press“SCAN”a second time.
*
[AS29530(ALL)08/95]


How to change the side of the tape being played
*
[AS29535(ALL)01/95]
The alternate side of the tape can be selected by pressing the
“SIDE 1-2”button.
*
[AS29540(ALL)08/95]
How to eject the tape
*
[AS29545(ALL)01/95]
To stop the tape and eject the cassette, press the“EJ”button.
The radio will resume playing if the radio power is on. The
tape cartridge can be ejected with radio power (and/or ignition)
on or off.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

Electronic Sound Systems
229
*
[AS29680(ALL)08/95]


Loose labels on cassette tapes can become lodged in the
mechanism. Remove any loose label material before inserting
cassette.
*
[AS29685(ALL)08/95]


Do not leave a tape in the cassette tape player. High heat in
the vehicle can cause the cassette to warp.
%*
[AS29690(ALL)08/95]
Clock Operation
*
[AS29695(ALL)08/95]
How to view the clock mode
[AS29705(ALL)09/94]
Press the“CLK”button to display time. The time will continue
to be displayed until a radio or tape function is chosen. After
approximately 10 seconds, the time will again appear in the
display. To display radio or tape information only, press the
“CLK”button a second time.
[AS29710(ALL)09/95]
NOTE: With the ignition off, the clock will display for
approximately 5 seconds once the“CLK”button is
depressed and released.
*
[AS29715(ALL)08/95]
How to set the clock
*
[AS29720(ALL)08/95]1.
Turn the radio on.
[AS29725(ALL)04/95]2.
Press and hold the“CLK”button, press the right (
a) side of
the“SEEK”button to increase hours. Press the left (
b) side
of the button to decrease hours. Press the right (
a) side of
the“TUNE”button to increase minutes. Press the left (
b)
side of the button to decrease minutes.
*
[AS29730(ALL)09/95]
NOTE: The clock displays 12-hour time with no AM/PM
indications.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

Electronic Sound Systems
233
*
[AS29830(ALL)01/95]
If the CD Changer is empty,“NO”and“DISC”will flash in the
display and radio play will continue.
*
[AS29835(ALL)02/95]
How to change the disc being played
[AS29840(ALL)10/94]
When in the CD mode, you can change discs by pressing the
right side (
a) of the“TUNE DISC”button (to select the next
discs) or the left side (
b) of the“TUNE DISCS”button (to
select previous discs). Play will begin on the first track of the
selected disc.
[AS29845(ALL)10/94]
If either side of the button is pressed and held, the CD Changer
will continue fast-forwarding or reversing through the discs in
the disc magazine. During these functions, the display will
indicate the disc number.
*
[AS29850(ALL)02/95]
How to change the track being played
[AS29855(ALL)04/94]
There are two ways to change the track being played. You can
use the“SEEK”or“SCAN”buttons.
[AS29860(ALL)04/94]


Using the“SEEK”function with your CD-Changer
[AS29865(ALL)10/94]
Press the right (
a) side of the“SEEK”button to seek
forward to the next track of the current disc. After the last
track has been completed, the CD player automatically
changes to the next disc.
[AS29870(ALL)04/94]
Press the left (
b) side of the“SEEK”button to seek to the
previous track on the current disc.
[AS29875(ALL)04/94]


Using the SCAN function with your CD Changer
[AS29880(ALL)10/94]
Press the“SCAN”button to move forward to the next track.
Approximately an eight-second sampling of the track will be
played before moving to the next track. The display will
indicate the disc and track number (dd-tt). At the end of the
disc, the CD Changer automatically changes to the next disc.
[AS29885(ALL)04/94]
To end the scan mode, press the“SCAN”button a second
time.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996