Page 67 of 387
65 [SR15910(E )08/95]
one third page art:0060562-B
[SR15920(E )08/95]
4. Slide either corner of the locking clip slot
closest to the tongue over both layers of
webbing. See Figure 3.
[SR15930(E )08/95]
one third page art:0060563-A[SR15940(E )08/95]
5. Pinch both opposite edges of webbing
together and insert them into the locking clip
slot. See Figure 4.
File:03ctsre.ex
Update:Tue Sep 19 15:05:35 1995
Page 68 of 387
66 [SR15950(E )08/95]
one third page art:0060564-A
[SR15960(E )08/95]
6. Pinch both layers of webbing together and
insert into other slot of locking clip. See
Figure 5.
[SR16970(E )08/95]
half page art:0060565-BFile:03ctsre.ex
Update:Tue Sep 19 15:05:35 1995
Page 69 of 387
67 [SR16980(E )08/95]
7. Re-buckle belt. Forcibly tilt the child seat
from side to side and also tug it forward to
see if it is held securely in place. See Figure
6. If excessive movement occurs, repeat steps
2 through 7 or properly install child seat in
a different seating position in the vehicle.
[SR16990(E )08/95]
RWARNING
Once you have attached the safety seat,
test the seat before you place the child in
it. Tilt the seat from side to side. Also try
to tug the seat forward. Check to see if
the belt holds the seat in place. If the lap
belt is too loose, tighten it by moving the
locking clip, or put the safety seat in
another seat and test it again. If the safety
seat is not anchored properly, the risk of a
child being injured in a collision or
sudden stop greatly increases. Reclining
seatbacks should be in the most upright
position for use with child safety seats.
File:03ctsre.ex
Update:Tue Sep 19 15:05:35 1995
Page 70 of 387
68 [SR17005(ALL)09/95]Installing Safety Seats in the Front Seat
(U.S. vehicles and Canadian 4-door sedan,
4-door hatchback and wagon vehicles)
[SR17010(ALL)09/95]
Your vehicle is equipped with a dual locking
mode retractor on the front lap belt (U.S.
vehicles) or the lap belt portion of the front
lap/shoulder belt (Canadian vehicles). The lap
belt will have the following label:
[SR17012(ALL)09/95]
half page art:0070267-B*
[SR17020(ALL)08/93]
The automatic locking modemust be usedwhen
installing a child seat in the front passenger seat.
[SR17025(ALL)01/95]
If you choose to install a forward-facing child
safety seat in a front seat with a dual locking
mode retractor:
[SR17026(ALL)01/95]
1. Move the front passenger seat as far back as
possible.
[SR17030(ALL)01/95]
2. Position the child seat in the front passenger
seat of the vehicle.
File:03ctsre.ex
Update:Tue Sep 19 15:05:35 1995
Page 71 of 387
69 [SR17035(ALL)03/95]
3. Follow the child seat manufacturer's
instructions. Route the lap or lap/shoulder
belt through the child seat and insert the belt
tongue into the buckle until you hear and
feel the latch engage.
[SR17040(ALL)01/95]
Be sure to follow the manufacturer's instructions
for belt routing.
[SR17045(ALL)01/95]
half page art:0070206-A
Routing the lap or lap/shoulder belt
[SR17070(ALL)01/95]
4. Grasp the lap portion of the belt below the
child seat label. Pull upward until all of the
belt is extracted and a click is heard. At this
time, the lap belt retractor is in the
automatic locking mode (child seat restraint
mode).
File:03ctsre.ex
Update:Tue Sep 19 15:05:35 1995
Page 72 of 387
70 [SR17075(ALL)09/95]
half page art:0070208-BSetting the automatic locking mode
[SR17080(ALL)03/95]
5. Allow the belt to retract. A clicking sound
will be heard as the belt retracts. This
indicates the retractor is in the automatic
locking mode. Push down on the child seat
while you pull down on the belt to remove
any slack in the belt.
File:03ctsre.ex
Update:Tue Sep 19 15:05:35 1995
Page 74 of 387
72 [SR17100(ALL)09/95]
half page art:0070210-CChecking that the seat is secure
[SR17105(ALL)01/95]
7. Double check that the retractor is in the
automatic locking mode. Try to pull more
belt out of the retractor, if you cannot, the
belt is in the automatic locking mode.
[SR17110(ALL)01/95]
8. Check to make sure that the child seat is
properly secured prior to each use. If the lap
belt is not locked, repeat steps 4 through 7.
[SR17115(ALL)09/95]
NOTE: When the safety belt is unbuckled and
allowed to retract completely, the
retractor will switch to the vehicle
sensitive (emergency) locking mode.
See the detailed instructions under
Front Passenger Lap Belt Retractorin
this chapter.
File:03ctsre.ex
Update:Tue Sep 19 15:05:35 1995
Page 75 of 387
73 [SR17118(E )08/95]
Installing Child Safety Seats in the Front
Passenger Seating Position (Canadian
2-door Hatchback vehicles)
[SR17120(E )06/95]
For vehicles equipped with a dual locking mode
retractor, use the following procedure.
*
[SR17125(E )06/95]
If you choose to install a child safety seat or
infant carrier in the front seating positions, move
vehicle seat as far back as possible.
*
[SR17130(E )06/95]
1. Position the child seat in the center of the
passenger seat.
*
[SR17135(E )09/95]
2. Pull down on shoulder belt, then grasp
shoulder belt and lap belt together. See
Figure 1.
*
[SR17137(E )09/95]
half page art:0011238-B
Pulling out belt webbing
File:03ctsre.ex
Update:Tue Sep 19 15:05:35 1995