1996 ACURA RL KA9 roof rack

Moonroof
Index
GLAS S
Removal , pag e 20-3 4
Adjustment , pag e 20-3 3
BRACKE T COVE R
CABLE ASSEMBL Y
Replacement , pag e 20-3 7
SUNSHAD ERemoval, pag e 20-3 4 MOONROO
F
CONTRO L
UNIT
SWITC H PLAT E BAdjustment ,page 20-4 0
GROUN DPLATE
RAIL HOLDE R A
FRAM E SEA L TUB
E
CLI P CLI P
(Righ t side )
FRAM E
Removal , pag e 20-3 6
REAR DRAI N
VALV E
FRONT DRAI NVALVE
FRONT DRAI NTUBE
REA R DRAI N
TUB E
TUB ECLIP
GUID E RAI L
Replacement , pag e 20-3 7
MOTO
R
Removal ,
pag e 20-3 6
INNE
R
CABL E
HOLDE RCOVER
RAIL HOLDE R B
GLAS
S BRACKE T
Removal ,
pag e 20-3 4
SHIM S
DRAI N CHANNE L SWITC
H PLAT E A
Adjustment ,page 20-3 9
ProCarManuals.com

Moonroof
Glass, Glas s Bracket , an d Sunshad e Remova l
6. Remov e th e drai n channel.
DRAI N CHANNE L
SCREW
1. Clos e th e glas s fully .
2 . Slid e th e sunshad e al l th e wa y back .
3 . Remov e bot h bracke t covers .
BRACKE T COVE R
Forwar d PLU
G
4. Remov e th e nut s fro m bot h glas s brackets .
GLASS BRACKE T
6 x 1. 0 m m9 N- m (0. 9 kgf-m , 7 Ibf-ft )
5. Remov e th e glas s b y liftin g u p an d pullin g forwar d
as shown .
NOTE: D o no t damag e th e roo f panel .
GLASS SCRE
W
7. Remov e th e holde r cover , the n remov e th e rai l
holde r B .
6 x 1. 0 m m9 N- m (0. 9 kgf-m ,
7 Ibf-ft )
COVE
R
GUIDE PI N
8. Usin g th e moonroo f wrench , mov e th e glas s bracke t
t o th e positio n wher e th e moonroo f normall y pivot s
down , an d remov e th e screws .
SCREW S
GLASS BRACKE T
RAIL HOLDE R B
SCRE W
ProCarManuals.com

Moonroof

Switch Plate Adjustment (Fully Closed Position/Auto Stop Position) (cont'd)

5. Using the moonroof wrench, open the glass to the auto stop position as shown.

6. Using an open-end wrench, loosen the switch plate B mounting bolts.

7. Adjust position of switch plate B (switch cam) as shown.

NOTE:

Move switch plate B a little at a time, then secure switch plate B at the position where the switch cam contacts the

auto stop position switch (a faint click is heard).

Check that switch plate B contacts the cable bracket.

SWITCH CAM

INNER CABLE END

SWITCH

PLATE B

AUTO

STOP

POSITION

SWITCH
OPEN-END

WRENCH
SWITCH PLATE B

Forward

CABLE BRACKET
CABLE

BRACKET
BOLTS

GLASS

130 mm

(5.1 in.)

8. Check the operation of the glass (from the tilt-up position to the fully closed position, from the fully opened position

to the auto stop position, from the auto stop position to the fully closed position) by operating the moonroof switch.
CABLE BRACKETProCarManuals.com

Roof Moldin g
Remova l
CAUTION : Whe n pryin g wit h a flat-ti p screwdriver , wra p
it wit h protectiv e tap e t o preven t damage , an d us e pro -
tectiv e tap e o n th e body .
NOTE : Tak e car e no t t o scratc h th e body .
ROOFMOLDIN G
BRACKE T
PIN(Bod y side )
ROO F
MOLDIN G
PIN
BRACKE T
Installation i s th e revers e o f th e remova l procedure .
NOTE :
Tak e car e no t t o damag e th e windshiel d molding .
Make sur e th e roo f moldin g is installe d securely .
ROOF MOLDIN G
PROTECTIV E
TAP E
WINDSHIEL DMOLDING
ProCarManuals.com