1995 RENAULT MEGANE SCENIC timing belt

TOP AND FRONT OF ENGINE
Timing belt
11 F3R ENGINE
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Remove:
- the computer and its mounting,
- the accessories belt in the following manner:
Slacken the tensioner (4) by the central bolt,
using a 7 mm allen key, by a quarter turn (cut
the end of the tool to approximately 12 mm)
while holding the outer nut with a 22 mm open
wrench.
Slackening the tensioner using the 22 mm wrench
automatically damages the adjustment teeth,
destroying the air conditioning and/or power as-
sisted steering mounting.
SPECIAL TOOLING REQUIRED
TIGHTENING TORQUES (in daN.m)
Wheel bolt 9
Crankshaft pulley bolt 12
Engine suspended mounting bolt 6
Cylinder head suspended mounting bolt 2
Engine suspended mounting cover bolt 4
Timing belt tensioner nut 4
Star socket ST X 14 FACOM for example
Engine support tool DESVIL M300 for example
97295R1
Remove:
- the front right hand wheel,
- the front right protector at the end of the
wheel arch,
98710R
Mot. 1054TDC pin
Mot. 1273 Tool for checking belt tension
Mot. 1289-03 Fork for centring suspended
mounting limiter
EQUIPMENT REQUIRED
11-4

TOP AND FRONT OF ENGINE
Timing belt
11 F3R ENGINE
Remove:
- the plastic protector from the suspended en-
gine mounting cover,
- the suspended mounting and cover,
- bolts (1) from the fuel pipe mounting,
- the two timing covers (2) and (3),
98897R
98982R
Note : the timing belt is captive on its mounting.
Remove the TDC plug.
Turn the crankshaft to the timing adjustment po-
sition (see diagram below) and insert the TDC pin
Mot. 1054. - the crankshaft pulley bolt,
- the tie bar between the shock absorber turrets.
Fit the engine support tool
DESVIL M300 for
example.
- the suspended mounting support (4) on the cy-
linder head.
99501-4R
11-5

TOP AND FRONT OF ENGINE
Timing belt
11 F3R ENGINE
Slacken the tensioner (T) and remove the belt.
Note : if the tensioner nut is slackened by more
than one turn, it may disengage.
REFITTING
Check that pin Mot. 1054 is in position.
Position the belt, ensuring :
- the fitting direction arrow (C) is located bet-
ween the intermediate shaft sprocket and the
tensioner,
- the reference marks on the belt are aligned
with the marks on the sprockets (engine remo-
ved or crankshaft output pulley removed) bet-
ween (A) and (B) 61 teeth.
Pretension the timing belt by tightening one bolt
(D) on the inner timing cover.
98901R
99501R
For the method for tensioning the belt (see sec-
tion 07 Timing belt).
Lock the tensioner at 4 daN.m.
Refitting is then the reverse of removal.
Fit the limiter assembly with the suspended moun-
ting cover.
ADJUSTING THE LONGITUDINAL MOVEMENT
LIMITER
Slacken limiter bolts (E).
Insert the limiter centring fork Mot. 1289-03 into
the openings in the suspended mounting cover.
99166-1R
Tighten the 2 bolts (E) to a torque of 5 to
6.5 daN.m.
11-6

TOP AND FRONT OF ENGINE
Timing belt
11F8Q ENGINE
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Remove:
- the front right hand wheel,
- the protection at the end of the wheel arch,
SPECIAL TOOLING REQUIRED
Mot. 1054TDC pin
Mot. 1202 Hose clip pliers
Mot. 1273 Tool for checking belt tension
Mot. 1289-03 Fork for centring suspended
mounting limiter
TIGHTENING TORQUES(en daN.m)
Wheel bolt 9
Crankshaft pulley bolt 12
Suspended mounting limiter bolt 6
Suspended mounting cover bolt 4
Tensioner nut 5
EQUIPMENT REQUIRED
Star socket ST X 14 FACOM for example
Engine support tool DESVIL M300 for example
98710R
- the acoustic tie bar between the shock absor-
ber turrets,
- the right hand suspended mounting cap.
Position the engine support tool
DESVIL M300
for example.
98982R
11-7

TOP AND FRONT OF ENGINE
Timing belt
11F8Q ENGINE
99309R2
Remove:
- the suspended mounting cover and the move-
ment limiter,- the lower timing casing (1),
- the alternator drive belt (see section 16
"Removing the alternator"),
Turn the crankshaft to position the camshaft ti-
ming reference mark in the timing window.
99176G
89120-2S
11-8

TOP AND FRONT OF ENGINE
Timing belt
11F8Q ENGINE
99183R
Fit the TDC pin , Mot.1054.
Remove:
- the fuel pipe mounting bolts (A),
- the timing covers (2) and (3).
99176R
11-9

TOP AND FRONT OF ENGINE
Timing belt
11F8Q ENGINE
92600R1
Slacken the tensioner and remove the belt.
Note : if the tensioner nut is slackened by more than one turn, it may disengage.
REFITTING (special notes)
Check that tool Mot. 1054 is in position.
Fit the belt, aligning the reference marks on the pulleys and belt.
Injection pump reference mark: B
(BOSCH), R (LUCAS DIESEL)
11-10

TOP AND FRONT OF ENGINE
Timing belt
11F8Q ENGINE
99175-1R
Tighten the timing belt by tightening one bolt (B)
on the inner timing cover.
99174-2R1
Fit tool Mot. 1273 and tension the belt until the
fitting tension is obtained (see section 07, Timing
belt tension ).
Tighten the tensioner nut to 5 daN.m.
It is vital to tighten the tensioner nut to 5 daN. m
to avoid any loosening of the tensioner which
could damage the engine.
Refit the crankshaft pulley and ensure the bolt is
tightened to a torque of 12 daN.m.
Refitting is then the reverse of removal.
Fit the suspended mounting cover assembly and
the movement limiter.
ADJUSTING THE LONGITUDINAL MOVEMENT
LIMITER
Slacken limiter bolts (4).
Insert the limiter centring fork Mot. 1289-03 into
the openings in the suspended mounting cover.
Tighten the limiter bolts (4) to a torque of
5.5 daN.m.
Check the injection pump timing (see section 13,
injection pump).
11-11