1995 RENAULT MEGANE SCENIC brake pads

MANUAL GEARBOX
Gearbox (Removal - Refitting)
21
Position the driveshaft with respect to the sun-
wheel, pivot the stub-axle carrier and engage the
driveshaft into the sunwheel using the shouldered
pin B.Vi. 31-01 in order to align the holes.IMPORTANT
Fit the bolt (V) and the starter motor centring do-
wel (D) correctly :
E and K engines
A chamfer on the leading edge of the sunwheel
makes it easier to fit new roll pins.
Seal the ends
(RHODORSEAL 5661).
Fill with fluids.
Fit the caliper mounting bolts with Loctite
FRENBLOC and tighten to the correct torque.
Press the brake pedal several times to bring the
pistons back into contact with the brake pads. E and K
engines
86070R3
Reconnect the speedo cable, ensuring that the clip
is the correct way round.
92108-1S
74937-4S
Tighten all nuts and bolts to the recommended
torques.
Fill the gearbox with oil.
21-12

MANUAL GEARBOX
Gearbox (Removal - Refitting)
21
Position the driveshaft with respect to the sun-
wheel, pivot the stub-axle carrier, engaging the
driveshaft into the sunwheel using the shouldered
pin B.Vi. 31-01 in order to align the holes. F engine
A chamfer on the leading edge of the sunwheel
facilitates makes it easier to fit new roll pins.
Seal the ends
(RHODORSEAL 5661).
Fill with fluids.
Fit the caliper mounting bolts with Loctite
FRENBLOC and tighten to the correct torque.
Press the brake pedal several times to bring the
pistons back into contact with the brake pads. F
engine
86070-1R1
Check the adjustments of the upper mountings
(refer to chapter 10).
Ensure that the movement limiter is mounted the
correct way round: the nuts should be fitted on
the exhaust pipe side.
92661S
74937-4S
Tighten all nuts and bolts to the recommended
torques.
Fill the gearbox with oil.
21-18

AUTOMATIC TRANSMISSION
Automatic transmission (Removal - Refitting)
23
K7M
ENGINE
Separate the gearbox from the engine by :
- removing the starter motor,
- removing the bolts from the automatic trans-
mission sump.
Remove:
- the hoses on the exchanger, Lift the engine from the sub-frame.
91131S
- the converter bolts
- the bolts around the gearbox and the TDC sen-
sor.
Separate the automatic transmission from the en-
gine.
REFITTING (special notes)
Refit the converter by positioning it with respect
to the mounting bolts.
Tighten the bolts around the automatic transmis-
sion.
Refitting is the reverse of removal.
Aligning the engine sub-frame with the body will
be made easier by positioning two approximately
100 mmlong threaded rods in the two front sub-
frame-body mountings.
Tighten the sub-frame front mounting bolts to a
torque of 6 daN.m. and to a torque of 11 daN.m at
the rear.
Tighten all nuts and bolts to the re-
commended torque.
Fit the caliper mounting bolts using Loctite
FRENBLOC and tighten them to the correct tor-
que.
Press the brake pedal several times to bring the
pistons back into contact with the brake pads.
Fill:
- the cooling circuit and purge it (see chapter 19),
- the engine with oil if necessary.
NOTE : check that the steering shaft yoke spacer is
in place when refitting.
99586R2
23-19

31
FRONT AXLE
Brake padsLUCAS
(Girling)

31
FRONT AXLE
Brake padsLUCAS
(Girling)