1995 RENAULT MEGANE SCENIC wiring diagram

Page
COOLING
Specifications
Filling - bleeding
Checking
Radiator
Diagram
Exhaust
General
Catalytic converter
Exhaust pipe assembly
Fuel tank
Fuel tank
Filler neck
Gauge
Pump and sender unit
Engine suspension
Suspended engine mountings
Engine mounting pads19-1
19-2
19-3
19-4
19-6
19-12
19-15
19-16
19-19
19-23
19-25
19-26
19-29
19-32 COOLING - EXHAUST- FUEL TANK -
ENGINE SUSPENSION
1916-1
16-9 STARTING - CHARGING
Alternator
Starter motor
16
IGNITION - INJECTION
IGNITION
Power module
Static ignition
Spark plugs
Injection
General
Location of components
Special notes on semi-sequential
injection
Special notes on sequential injection
Injection fault warning light
Engine immobiliser function
Computer configuration as a
function of the gearbox type
17
14-1
14-9
14-13
14-19
14-21
14-22 ANTIPOLLUTION
Fuel vapour recirculation
Oil vapour rebreathing
Exhaust gas recirculation (EGR)
Catalytic converter
Catalytic converter - oxygen sensor
Test for the presence of lead
14
17-28
17-29
17-32
17-33
17-34
17-36
17-39 IGNITION - INJECTION
(continued)
Injection strategy / automatic
transmission
Injection strategy / air conditioning
Idle speed correction
Idle speed adaptive correction
Richness regulation
Adaptive richness correction
Operating wiring diagram
17
Page
17-1
17-2
17-5
17-6
17-12
17-17
17-19
17-24
17-25
17-26
Contents

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F8Q engine
- the pipes and connectors for the fast idle and
EGR solenoid valves,
- the brake servo pipe,
- the accelerator and clutch cables,
- the diesel fuel filter connector,
- the compressor feed wire (if fitted).
Remove:
- the cooling assembly (see section 19
"Radiator"),
- the alternator belt (see section 16),
- the compressor mounting bolts (if fitted) and
attach it to the front cross member.
NOTE: cut the base of tool Mot. 1159 to 30 mm.
99023R2
99024R2
Remove the oil filter.
Unclip the alternator wiring and move it to one
side.
Diagram for drilling tool Mot. 1159. (For
instructions on use, refer to page 10-40).
99028R
Fit tool Mot. 1159.
10-39

FUEL SUPPLY
Fuel cut-out on impact
13
WIRING DIAGRAM
Key
120Injection computer
199Fuel pump
236Fuel pump relay
246Fuel shut off
927Inertia switch
PRJ99472
13-2

INJECTION
Operating wiring diagram
17
KEY TO OPERATIONAL WIRING DIAGRAMS (E7J, F3R, K7M)
COMPONENT NO DESCRIPTION
109
119
120
146
147
149
193 to 196
218
222
224
225
228
236
238
242
244
247
250
272
310
319
341
371
398
437
565
597
645
649
663
664
679
746
772
777
927
MF
MHOn board computer
Automatic transmission computer
Injection computer
Pinking sensor (located under the inlet manifold for E7J engine)
Absolute pressure sensor
TDC sensor
Injectors
Fuel pump
Throttle position potentiometer
Power assisted steering pressostat
Diagnostic socket
Idle speed regulation micromotor
Fuel pump relay (in engine fuse box)
Injection feed locking relay
Oxygen sensor
Coolant temperature sensor
Instrument panel
Vehicle speed sensor
Air temperature sensor
Ignition power module
Air conditioning control panel
Idle speed regulation solenoid valve
Fuel vapour recirculation solenoid valve
Exhaust gas recirculation solenoid valve (EGR)
Throttle body heater (under throttle body)
Throttle body assembly
Engine fuse box
Passenger compartment connection unit
Idle speed regulation stepping motor
Dual ignition coil n°1 (cylinders 1 and 4)
Dual ignition coil n° 2 (cylinders 2 and 3)
Radio anti-interference condenser
Cylinder reference sensor
Heater relay (in engine fuse box)
Power fuse board (near battery)
Inertia switch
Rear right hand electrical earth
Engine electrical earth (located on the cylinder block between the starter and the al-
ternator for the E7J engine)
17-39

INJECTION
Operating wiring diagram
17
E7J engine
PRJ99528
17-40

INJECTION
Operating wiring diagram
17
E7J engine
COMPUTER TRACK ALLOCATION
TrackALLOCATION
1Power earth
2Electronic earth
3Vehicle speed information
4+ before ignition (permanent) computer memory
5Canister bleed signal (sequential earth period)
6Pump relay control (via track N° 2)
7Locking relay control (via track N° 2)
8Diagnostic line for erasing the memory and power assisted steering pressostat information
9Throttle position potentiometer information (pin N° 4 on 222)
10Heater relay command
11TDC sensor signal (track B)
12Rev counter information at instrument panel
13Connection with injection fault warning light on instrument panel
14Air temperature information
15Coolant temperature information
16+ 5 V feed for absolute pressure sensor and throttle potentiometer
17Common earth for absolute pressure sensor, throttle potentiometer and coolant temperature
sensor
18Emission of diagnostic signal to diagnostic socket
19Main computer feed via injection locking relay
20Air conditioning compressor command
21Injector control via earth
22Not used
23+ or - feed to idle speed micromotor (pin N° 1)
24+ or - feed to idle speed micromotor (pin N° 2)
17-41

INJECTION
Operating wiring diagram
17
E7J engine
TrackALLOCATION
25No load information input
26Not used
27Power module command
28TDC sensor signal input (track A)
29Immobiliser coded line input via decoder unit
30+ 12 V information when ignition turned on
31Pinking sensor noise signal input
32+ 12 V after ignition information
33Voltage information dependent on manifold pressure seen by sensor (on track B)
34Air conditioning compressor operation request input
35Voltage from oxygen sensor input
17-42

INJECTION
Operating wiring diagram
17
K7M engine
PRJ99475
17-43