1995 OLDSMOBILE AURORA light

Rear Window Defogger
LOW
R. DEFOG
@ R. DEFOG: Press to warm the defogger grid on
the rear window.
An indicator light in the button will
rear window defogger
will turn off automatically after
about
10 minutes of use. If you press it again, the
defogger
will operate for about five minutes only. You
can also turn the defogger off by turning off the ignition
or by pressing the
R. DEFOG switch again.
a olow while the rear window defogger is operating. The
Do not attach a temporary vehicle license across the
defogger grid on the rear window.
When you operate the rear window defogger, the outside
rearview mirrors are also heated to help remove ice and
fog.
NOTICE:
Don’t use a razor blade or something else sharp
on the inside
of the rear window. If you do, you
could cut or damage the warming grid, and the
repairs wouldn’t be covered by your warranty.
3-7
ProCarManuals.com

AMEM: Press this button to change between the AM,
FM1 and FM2 bands. The display will show which band
you are on. If you press this button while a tape or CD is
playing, the tape or CD will stop and the radio will
return to the AM or FM band that you were on.
TUNE: Press lightly on this knob to release it from its
recessed position. Turn
it to tune in radio stations. You
may push the knob back in to return it to its recessed
position when not
in use.
To Preset Radio Stations
The five pushbuttons labeled 1-5 can be used to preset up
to 15 radio stations (five AM, five FM 1 and five FM2).
1. Tune
in the station you want to store.
2. Press TONE to select the setting that you prefer.
3. Press and hold one of the five pushbuttons until the
display shows a channel number. The radio will mute
until the channel number is displayed. Whenever you
press that button again, the preset station and tone setting will return. Always check whether you’re in
AM, FMl or FM2.
SEEK A/V: When you press SEEK while playing the
radio,
the radio will search for the next higher or lower
station and stop. The radio will be muted while seeking.
SCAN: When you press SCAN while playing the radio,
the radio will
go through each station, pausing for a few
seconds at each station. Press SCAN again to stop on
a
station. The radio will be muted while scanning and
“SCAN”
will appear on the display.
When you press SCAN and hold
it for about two seconds
until the display shows “PSCAN’ (Preset Scan), the radio
will scan only stations that you’ve preset with your radio
pushbuttons. Press SCAN again to stop
on a station.
RCL (Recall): When the ignition is off, press RCL to
display the time. When the radio is on, press RCL to
switch the display between the radio station and the
time. After
five seconds the display will return to its
normal display.
The radio can be set
so that either the time or radio
station is normally displayed when the radio is playing.
To do this, press RCL to display the time or radio
stations as desired, then hold
RCL down until the
display flashes.
3-10
ProCarManuals.com

This button scrolls through three functions when a CD is
playing:
0 Press to see which track is playing.
0 Press again while the track is displayed (within about
five seconds), and “EL
TM” (Elapsed Time) will
appear in the display together with how much time
has elapsed since
the track started playing.
0 Press again to view the time.
You can select which function is normally displayed
when a
CD is playing. To do this, press RCL until the
display shows the desired function, then hold RCL down
until
the display flashes.
TONE: This button controls the Automatic Tone
Control (ATC) feature which lets
you select an
equalization for the type of music or voice being heard.
For example, JAZZ emphasizes bass and treble while
ROCK emphasizes bass. Press TONE to step through
the
six settings: JAZZ, VOCAL, POP, ROCK,
CLASSIC, and MANUAL. Each setting will appear on
the display. In MANUAL you can adjust tone with the
TREB and BASS controls. Any time TREB or BASS is
turned, TONE will automatically go to the MANUAL
setting. Separate
tone settings can be stored with each
preset station. You can also select separate tone settings
for your cassette tape and compact disc.
BASS: Press this button lightly to release it from its
recessed position. Turn it
to adjust bass response. As
you turn the knob, you will feel the center position. Push
the knob back in to return it to its recessed position.
Turning BASS will change the radio’s Automatic Tone
Control feature to MANUAL.
TREB (Treble): Press this button lightly to release it
from its recessed position, then pull
it out to its fully
extended position. Turn it to adjust treble response. As
you turn the knob you will feel the center position. Push
the knob back in to return
it to its recessed position.
Turning TREB will change the radio’s Automatic Tone
Control feature to MANUAL.
BAL (Balance): Press this button lightly to release it
from its recessed position. Turn
it to adjust the right and
left speaker balance. As you turn
the knob you will feel
the center position. Push the knob back in to return it to
its recessed position.
FADE: Press this button lightly to release it from its
recessed position, then pull
it out to its fully extended
position. Turn it to
the right to increase front speaker
volume. Turn
it to the left to increase rear speaker
volume. As you turn the knob
you will feel the center
position. Push the knob back
in to return it to its
recessed position.
3-11
ProCarManuals.com

PWWVOL (PowerNolume): With the ignition on,
push this knob to turn the system on or off. Turn it
clockwise to increase the volume. Turn it
counterclockwise to decrease the volume.
AMD": Press this button to change between the AM,
FMI and FM2 bands. The display
will show which band
you are on.
If you press this button while a tape is
playing, the tape
will stop and the radio will return to
the AM or FM band that you were on.
TUNE: Press lightly on this knob to release it from its
recessed position. Turn
it to tune in radio stations. You
may push the knob back
in to return it to its recessed
position when not
in use.
To Preset Radio Stations
The five pushbuttons labeled 1-5 can be used to preset LIP
to 15 radio stations (five AM, five FM 1 and five FM2).
1. Tune in the station you want to store.
2. Press and hold one of the five pushbuttons
until the
display shows
a channel number. The radio will mute
until the cl1annel number is displayed. Whenever you
press that button again, the preset station
will return.
Always check whether you're
in AM, FMl or FM2.
SEEK A/V: When you press SEEK while playing the
radio, the radio
will search for the next higher or lower
station and stop. The radio will be muted while seeking.
SCAN: When you press SCAN while playing the radio,
the radio
will go through each station, pausing for a few
seconds at each station. Press SCAN again to stop
on a
station. The radio
will be muted while scanning and
"SCAN"
will appear on the display.
When you press SCAN and hold
it for about two
seconds
until the display shows "PSCAN" (Preset Scan),
the radio
will scan only stations that you've preset with
your radio pushbuttons. Press SCAN again to stop on a
station.
RECALL: When the ignition is off, press RECALL to
display the time. When the radio
is on, press RECALL
to switch the display between the radio station and the
time. After five seconds the display
will return to its
normal display.
The radio can be set
so that either the time or radio
station is normally displayed when the radio is playing.
To
do this. press RECALL to display the time or radio
station
as desired, then hold RECALL down untii the
display flashes.
ProCarManuals.com

BASS: Press this button lightly to release it from its
recessed position. Turn
it to adjust bass response. As
you turn the knob you
will feel the center position. Push
the knob back
in to return it to its recessed position.
TREB (Treble): Press this button lightly to release it
from its recessed position, then pull it out to its fully
ext.ended position. Turn it to adjust treble response. As
you turn the knob you will feel the center position. Push
the knob back
in to return it to its recessed position.
BAL (Balance): Press this button lightly to release it
from its recessed position. Turn it to adjust the right and
left speaker balance. As you turn the knob you will feel
the center position. Push the knob back
in to return it to
its recessed position.
FADE: Press this button lightly to release it from its
recessed position,
then pull it out to its fully extended
position. Turn
it to the right to increase front speaker
volume. Turn it to the left to increase rear speaker
volume.
As you turn the knob you will feel the center
position. Push the knob back
in to return it to its
recessed position.
To Play a Cassette Tape
With the ignition on, insert the tape and it will begin
playing. The audio system will turn on automatically.
Your tape player is designed to work best
with tapes that
are
30 to 45 minutes long on each side. Longer tapes
may not work as well.
Note that when a tape is inserted, “TP” will be
displayed. When the tape is playing,
a box will appear
around “TP”
in the display along with an arrow to show
whether the top or bottom of
the tape is playing. Any
time a tape is inserted, the top side will play first. If
a
high-bias metal or CrO2 tape is played, “HI-BIAS” will
appear
in the display and the equalization will be
adjusted automatically.
If “Cln” (Clean) appears on the display when you insert
your cassette tape, your cassette player needs to be
cleaned. It will still play cassette tapes, but
it should be
cleaned
to prevent damage to your cassette tapes and the
cassette tape player. See “Care of Your Cassette Tape
Player” later
in this section. After you have cleaned the
cassette tape player, press and hold EJECT for five
seconds to reset the Cln indicator. The radio will display
bb---” to show that the clean feature has been reset.
3-16
ProCarManuals.com

AR/VFM Stereo Radio with Automatic Tone
Control and Cassette Tape Player PWRNOL (PowerNolume): With the ignition on,
push this knob to turn the system on
or off. Turn it
clockwise to increase the volume. Turn
it
counterclockwise to decrease the volume.
AMEM: Press this button to change between the AM,
FMl and FM2 bands. The display will show which band
you are on.
If you press this button while a tape is
playing, the tape will stop and
the radio will return to
the
AM or FM band that you were on.
TUNE: Press lightly on this knob to release it from its
recessed position. Turn it to tune in radio stations. You
may push
the knob back in to return it to its recessed
position when
not in use.
To Preset Radio Stations
The five pushbuttons labeled 1-5 can be used to preset up
to
15 radio stations (five AM, five FM1 and five FM2).
1. Tune in the station you want to store.
2. Press TONE to select the setting that you prefer.
This audio
system may have an optional trunk-mounted
CD changer.
If so, also see “Trunk-Mounted CD
Changer” later in this section.
The digital display indicates information on time or radio
3. Press and hold one of the five pushbuttons until the
station frequency, the AM or FM radio band, whether the
display shows a channel number. The radio will mute
station is
in stereo, and other audio system functions. until the channel number is displayed. Whenever you
press that button again, the preset station and tone
setting will return. Always check whether you’re
in
AM, FMl or FM2.
3-18
ProCarManuals.com

SEEK A/V: When you press SEEK while playing the
radio, the radio will search for the
next higher or lower
station and stop. The radio will be muted while seeking.
SCAN: When you press SCAN while playing the radio,
the radio
will go through each station, pausing for a few
seconds at each station. Press SCAN again to stop on a
station. The radio will be muted while scanning and
“SCAN” will appear on the display.
When you press SCAN and hold
it for about two
seconds
until the display shows “PSCAN” (Preset Scan),
the radio will scan only stations that you’ve preset with
your radio pushbuttons. Press SCAN again to stop on a
station.
RCL (Recall): When the ignition is off, press RCL to
display the time. When the radio is on, press RCL to
switch the display between the radio station and the
time. After
five seconds the display will return to its
normal display.
The radio can be set
so that either the time or radio
station is normally displayed when the radio is playing.
To
do this, press RCL to display the time or radio station
as desired. Then hold RCL down
until the display
flashes.
TONE: This button controls the Automatic Tone
Control (ATC) feature which lets you select an
equalization for the type of music
or voice being heard.
For example, JAZZ emphasizes bass and treble while
ROCK emphasizes bass. Press TONE to step through
the six settings: JAZZ, VOCAL, POP, ROCK,
CLASSIC, and MANUAL. Each setting will appear on
the display. In MANUAL you can adjust tone with the
TREB and BASS controls. Any time TREB
or BASS is
turned, TONE will automatically go to the MANUAL
setting. Separate tone settings can be stored
with each
preset station. You can also select a separate tone setting
for
your cassette tape.
BASS: Press this button lightly to release it from its
recessed position. Turn
it to adjust bass response. As
you turn the knob you
will feel the center position. Push
the knob back
in to return it to its recessed position.
Turning BASS will change the radio’s Automatic Tone
Control feature to MANUAL.
TREB (Treble): Press this button lightly to release it
from its recessed position, then pull
it out to its fully
extended position. Turn it to adjust treble response. As
you
turn the knob you will feel the center position. Push
the knob back in to return
it to its recessed position.
Turning TREB will change the radio‘s Automatic Tone
Control feature to MANUAL.
3-19
ProCarManuals.com

BAL (Balance): Press this button lightly to release it
from its recessed position. Turn it to adjust the right and
left speaker balance.
As you turn the knob you will feel
the center position. Push the knob back in to return
it to
its recessed position.
FADE: Press this button lightly to release it from its
recessed position, then pull
it out to its fully extended
position. Turn it to the right to increase front speaker
volume. Turn it to
the left to increase rear speaker
volume.
As you turn the knob you will feel the center
position. Push the knob back
in to return it to its
recessed position.
To Play a Cassette Tape
With the ignition on, insert the tape and it will begin
playing. The audio system will turn on automatically.
Your tape player is designed to work best
with tapes that
are
30 to 45 minutes long on each side. Longer tapes
may not work as well.
Note that when a tape is inserted, “TP? will be
displayed. When the tape is playing, a box
will appear
around
“TP’ in the display along with an arrow to show
whether the
top or bottom of the tape is playing. Any
time a tape is inserted, the top side will play first. If LI
high-bias metal or CrO2 tape is played, “HI-BIAS” will
appear in the display and the equalization
will be
adjusted automatically. If you select a tone setting, it
will be activated each time
you play a tape.
If “Cln” (Clean) appears on
the display when you insert
your cassette tape, your cassette player needs to be
cleaned. It will still play cassette tapes, but
it should be
cleaned to prevent damage to your cassette tapes and the
cassette tape player. See “Care
of Your Cassette Tape
Player” later
in this section. After you have cleaned the
cassette tape player, press and hold EJECT for five
seconds to reset the Cln indicator. The radio will display
&‘---’? to show that the clean feature has been reset.
If “Err” or
“E” and a number appear on the display at
any time, an error has occurred. See “Cassette Tape and
CD Errors” later in this section.
NR (Noise Reduction): This radio has Dolby@B Noise
Reduction to reduce background noise on Dolby@B
encoded tapes. Press this button to reduce background
noise on your tape. The Dolby symbol
00 will appear
in the display. Dolby@ Noise Reduction is manufactured
under license from Dolby Laboratories Licensing
Corporation. Dolby@ and
the 00 symbol are
trademarks
of Dolby Laboratories Licensing
Corporation.
3-20
ProCarManuals.com