1995 OLDSMOBILE AURORA light

NOTICE:
Ignoring these steps could result in costly damage
to
your vehicle that wouldn’t be covered by your
warranty.
Trying
to start your Aurora by pushing or pulling
it won’t
work, and it could damage your vehicle.
To Jump Start Your Aurora:
1. Check the other vehicle. It must have a I2-volt
battery
with a negative ground system.
NOTICE:
If the other system isn’t a 12-volt system with a
negative ground, both vehicles can be damaged.
2. Get the vehicles close enough so the jumper cables
can reach, but be s~lre the vehicles aren’t touching
each other. If they are,
it could cause a ground
connection you don’t want. You wouldn’t be able
to
start your Aurora, and the bad grounding could
damage the electrical systems.
You could be injured
if the vehicle rolls. Set the
parking brake firmly on each vehicle. Put an
automatic transaxle in PARK (P) or a manual
transaxle
in NEUTRAL (N).
3. Turn off the ignition on both vehicles. Turn off all
lights that aren’t needed, and radios. This
will avoid
sparks and help
save both batteries. And it could
save your radio!
I NOTICE:
If you leave your radio on, it could be badly
damaged. The repairs wouldn’t be covered by
your warranty.
5-3
ProCarManuals.com

If You’re Stuck: In Sand, Mud, Ice or
Snow I NOTICE:
Spinning your wheels can destroy parts of your
vehicle as well as the tires. If you spin the wheels
too fast while shifting your transaxle back and
forth, you can destroy your transaxle. What you don’t want to do when your vehicle is stuck is
to spin your wheels too fdst. The method known
as
“rocking” can help you get out when you’re stuck, but
you must use caution.
For information about using tire chains on your vehicle,
see “Tire Chains’’
in the Index.
Rocking Your Vehicle to Get It Out:
First, turn your steering wheel left and right. That will
clear the area around your front wheels. You should turn
your traction control system
off. (See ”Traction Control
System”
in the Index.) Then shift back and forth
between REVERSE
(R) and a forward gear, spinning the
wheels
as little as possible. Release the accelerator pedal
while you shift, and press lightly
on the accelerator
pedal when the transaxle
is in gear. If that doesn’t get
you out after
a few tries, you may need to be towed out.
If you do need to be towed out, see “Towing Your
Vehicle”
in the Index.
5-30
ProCarManuals.com

Engine Accessory Belt
The 4.0L Aurora engine uses an engine accessory belt.
This diagram shows the features connected by the belt
routing. See”Maintenance Schedu1e”in the Index for
when to check the belt.
1. Tensioner Arm Pulley
2. Power Steering Pump Pulley
3. Idler Pulley 4.
Alternator Pulley
5. Air Conditioner Compressor Pulley
6. Harmonic Balancer
Engine Oil
If the CHECK 01L LEVEL message or the oil warning
light on the instrument panel comes
on, it means you
need to check your engine oil level right away.
For more
information, see “Check Oil Level Message” or
“Oil
Warning Light” in the Index. You should check your
engine
oil level regularly; this is an added reminder.
It’s a
good idea to check your engine oil every time you
get fuel. In order to get an accurate reading, the oil must
be warm and the vehicle must be on level ground.
Turn off the engine and give the
oil a few minutes to
drain back into the oil pan.
If you don’t, the oil dipstick
might not show the actual level.
6-10
ProCarManuals.com

Engine Coolant
The following explains your cooling system and how to
add coolant when
it is low. If you have a problem with
engine overheating, see “Engine Overheating” in the
Index.
The proper coolant for your Aurora will:
0 Give freezing protection down to -34°F (-37°C)
0 Give boiling protection up to 262°F (128°C).
0 Protect against rust and corrosion.
0 Help keep the proper engine temperature.
0 Let the warning lights work as they should.
What to Use
Use a mixture of one-half c.lt.crr~ wwtor (preferably
distilled) and one-half antifreeze that meets “GM
Specification 182S-M,” which won‘t damage aluminum
parts.
You call also use a recycled coolant conforming to
GM Specification 1825-M
with a complete coolant tlush
and refill. Use GM Engine Coolant Supplement (sealer)
with any cotnplete coolant flush and refill. If you use
this mixture, you don‘t need to add anything else.
A
special procedure is required for adding sealer; see the
ALI~o~~ Service Manual. (To order a service 1nanual. see
”Service Publications“
in the Index.)
ProCarManuals.com

should have your brake system fixed, since a leak means
that sooner or later your brakes won’t work well, or
won’t work at all.
So, it isn’t a good idea to “top off’
your brake fluid. Adding brake fluid won’t correct
a
leak. If you add fluid when your linings are worn, then
you’ll have too much fluid when you get new brake
linings.
You should add (or remove) brake fluid, as
necessary, only when work is done on the brake
hydraulic system.
When your brake fluid falls
to a low level, your brake
warning light
will come on. A chime will sound if you
try to drive
with this warning light on. See “Brake
System Warning Light”
in the Index. What to
Add
When
you do need brake fluid, use only DOT-3 brake
fluid
-- such as Delco Supreme 11 @ (GM Part
No. 1052535). Use new brake fluid from a sealed
container only, and always clean the brake fluid
reservoir cap before removing it.
I NOTICE:
Don’t let someone put in the wrong kind of
fluid. For example, just a few drops
of
mineral-based oil, such as engine oil, in
your brake system can damage brake
system parts
so badly that they’ll have to be
replaced.
Brake fluid can damage paint, so be careful
not
to spill brake fluid on your vehicle. If
you do, wash it off immediately. See
“Appearance Care” in the Index.
6-24
ProCarManuals.com

Brake Wear
Your Aurora has four-wheel disc brakes.
Disc brake pads have built-in wear indicators that make
a high-pitched warning sound when the brake pads are
worn and new pads are needed. The sound may come
and
go or be heard all the time your vehicle is moving
(except when
you are pushing on the brake pedal
firmly).
I NOTICE:
Continuing to drive with worn-out brake pads
could result in costly brake repair.
Some driving conditions or climates may cause a brake
squeal when the brakes are first applied or lightly
applied. This does not mean something is wrong
with
your brakes.
Brake linings should always
be replaced as complete
axle sets.
Brake Pedal Travel
See your retailer if the brake pedal does not return to
normal height, or
if there is a rapid increase in pedal
travel. This could be
a sign of brake trouble.
Brake Adjustment
Every time YOLI apply the brakes, with or without the
vehicle moving, your brakes adjust for wear.
6-25
ProCarManuals.com

Headlamp Aiming
Your vehicle has the composite headlamp system. These
headlamps have horizontal and vertical aim indicators.
The
aim has been pre-set at the hctory and should need
no further adjustment.
If your vehicle is damaged in an accident and the
headlamp aim seems to be affected, see your Aurora
retailer. Headlamps
on damaged vehicles may require
recalibration
of the horizontal aim by your Aurora
retailer.
To check the aim, the vehicle should be properly
prepared as follows:
The vehicle must have all four tires on a perfectly
level surface.
The vehicle should not have any snow, ice, or mud
attached
to it.
0 There should not be any cargo or loading of vehicle,
except
it should have a full tank of gas and one
person or
160 Ibs. (75 kg) on the driver's seat.
Tires should be properly inflated.
I NOTICE:
To make sure your headlamps are aimed
properly, read all the instructions before
beginning. Failure to
follow these instructions
could cause damage to headlamp parts.
State inspection stations will allow a vertical reading of
plus
0.76 degrees or minus 0.76 degrees from the center
of the bubble.
It is recolnmended that the upper limit not exceed plus
0.4 degrees from the center of the bubble. Other drivers
may flash their bright lights at you
if your adjustment is
much above plus 0.4 degrees.
If you find that the headlamp aiming needs adjustment,
follow these steps:
Start with the vertical headlamp aim. Don't try to adjust
the horizontal aim first. Adjustment screws can be
turned
with an E8 Torx@socket or T1S TorxB
screwdriver.
6-28
ProCarManuals.com

0 If a ring forms after spot cleaning, clean the entire
area immediately or
it will set.
Using Foarn-']lSrpe Cleaner on Fabric
0
0
0
0
0
0
Vxuum and brush the area to remove any loose dirt.
Always clean a whole trim panel or section. Mask
surrounding trim along stitch or welt lines.
Mix Multi-Purpose Powdered Cleaner following the
directions
011 the container label.
Use suds only and apply with a clean sponge.
Don't saturate the material.
Don't rub
it roughly.
As soon as you've cleaned the section, use a sponge
to remove the suds.
Rinse the section with
a clean, wet sponge.
Wipe off what's left
with a slightly damp paper towel
or cloth.
Then dry
it immediately with a blow dryer or a heat
lamp.
NOTICE:
I Be careful. A blow dryer may scorch the fabric. I
0 Wipe with a clean cloth.
Using Solvent-Type Cleaner on Fabric
First, see if you have to use solvent-type cleaner at all.
Some spots and stains
will clean off better with just
water and mild soap.
If you need to use a solvent:
0 Gently scrape excess soil from the trim material with
a clean, dl111 knife or scraper. Use very little cleaner,
light pressure and clean cloths (preferably
cheesecloth), Cleaning should start at the outside
of
the stain, "feathering" toward the center. Keep
changing to
a clean section of the cloth.
0 When you clean a stain from fabric, immediately dry
the area
with a blow dryer to help prevent a cleaning
ring. (See the previous NOTICE.)
6-44
ProCarManuals.com