1995 LAND ROVER DISCOVERY light

76CHASSIS AND BODY
16
REPAIR ALPINE LIGHT TRIM CASING
Service repair no - 76.13.20
Remove
1.Remove RH 'E' post trim casing.
See 'E' post
trim casing - rh.
2.Remove rear seat belt anchorage retaining bolt
cover.
3.Remove bolt securing rear seat belt anchorage.
4.Remove 2 trim studs securing trim casing.
5.Release trim casing from 2 retaining studs.
6.Remove trim casing.
Refit
7.Fit and align trim casing and secure with studs.
8.Fit 2 trim studs securing trim casing.
9.Position seat belt anchorage, fit bolt and tighten
to
32 Nm (24 lbf ft).
10.Fit cover to seat belt anchorage bolt.
11.Fit 'E' post trim casing.
See 'E' post trim
casing - rh.

CHASSIS AND BODY
17
REPAIR FRONT BODYSIDE TRIM CASING
Service repair no - 76.13.01
Remove
1.Remove the grab handle.
2.Remove the rear compartment lower trim panel.
See rear compartment lower trim panels.
3.Remove the alpine light trim casing.See alpine
light trim casing.
4.Remove the bolts securing the upper and lower
seat belt mountings.
5.Remove the finisher from its location over the
seat belt inertia reel.
6.Remove the front seat belt guide from the upper
aperture in the casing.
7.Open the side window, remove the catch
securing screws and withdraw the catch trim.
8.Remove the side window hinge finishers.
9.Release the casing from the window rubber.
10.Release the rear seat belt from the guide
attached to the casing.
11.Fold down the rear seats and carefully ease the
casing from the fastenings.
12.Pass the front seat belt through the upper
aperture and withdraw the casing from the
vehicle.
Refit
13.Reverse removal procedure.
NOTE: Ensure that the trim material glued
to the door post is not wrinkled when the
door seal is fitted.
14.Tighten upper and lower seat belt fixings to
32
Nm (24 lbf ft)
.

76CHASSIS AND BODY
18
REPAIR HEADLINING
Service repair no - 76.64.01/14
Remove
1.Disconnect battery negative lead.
2.Remove the lower trim panels from the rear
compartment.
See rear compartment lower
trim panels.
3.Remove the alpine light trim casing.See alpine
light trim casing.
4.Remove the front bodyside trim casing.See
front bodyside trim casing.
5.Remove the roof lights from the headlining
pocket and from the headlining.
6.Remove the front grab handles.
7.Remove the sun visors and their retaining clips.
8.Remove the front headlining pocket.9.Remove the finishers from the sun roof
apertures.
10.Release the headlining from the channel above
the rear door and manoeuvre it from the vehicle
through the rear door.
11.If the existing headlining is being replaced, if
fitted, remove the passenger net pockets and fit
them to the new headlining.
Refit
12.Reverse removal procedure.

CHASSIS AND BODY
19
REPAIR 'D' POST TRIM CASING
Service repair no - 76.13.73
Remove
1.Remove the rear compartment lower trim panel.
See rear compartment lower trim panels.
2.Remove the alpine light trim casing.See alpine
light trim casing.
3.Release the rear seat belt from the guide
attached to the casing.
4.Fold down the rear seats.
5.Release the D' post casing from the rear side
window seal and carefully ease the casing from
the fasteners.
Refit
6.Reverse removal procedure.BODY SIDE OPENING WINDOWS
Service repair no - 76.81.18
Remove
1.Remove the screws securing the catch to the
body and detach the catch trim.
2.Remove the hinge finishers from the hinges.
3.Remove the screws securing the glass to the
hinges, withdraw the glass and fixings taking
care not to lose the joint washers.
Refit
4.Reverse removal procedure.

CHASSIS AND BODY
33
REPAIR WINGS [FENDERS]
Service repair no - 76.10.24
Remove
1.Disconnect battery negative lead.
2.Remove the headlamp surround.
3.Remove the front bumper assembly.
4.Remove the indicator repeater light.
5.Remove the four screws securing the wing
[fender] at the 'A' post.
6.Remove the bolts securing the bottom of the
wing [fender] at the bumper retaining bracket
and at the sill finisher.
7.If removing the RH wing [fender] loosen the
radio aerial securing nut.
8.Remove the seven bolts from the drain channel
in the top of the wing [fender].
9.Break the sealed joints at the valance and 'A'
post; then complete the removal of the wing
[fender]. If removing a RH wing withdraw the
wing [fender] sufficiently to allow removal of the
aerial before completing the removal.Cleaning/painting
10.Thoroughly clean all traces of existing sealant
from the sealing faces of the valance and 'A'
post.
11.Paint the cleaned surfaces with etch primer.
12.If the existing wing [fender] is to be refitted
repeat the cleaning and painting procedure on
the wing [fender] sealing surfaces.
Refit
13.Apply 3M 8572 Bolted Panel Sealer to the joint
faces on the valance and 'A' post and to the
bracket face.
14.Refit the wing [fender], on RH wings [fenders] fit
the radio aerial, and secure with the bolts and
screws ensuring that the wing [fender] correctly
aligns with the bonnet [hood].

76CHASSIS AND BODY
44
REPAIR
7.Remove centre console switch pack cover.
8.Remove 4 screws securing switch pack to
console.
9.Release switch pack from console and
disconnect 7 multiplugs.
NOTE: If the 'Cold Pack' option is not fitted
there will only be 5 switches in pack.
10.Remove switch pack.
Models fitted with electric front seats
11.Release electric front seat switches from centre
console.
12.Disconnect 2 multiplugs from each switch.
13.Remove switches.All models
14.Release hand brake lever gaiter from centre
console.
15.Remove clip and clevis pin securing cable to
hand brake lever.
16.Remove 4 screws securing centre console to
body.
17.Raise hand brake lever, pull centre console
rearwards to gain access to cigar lighter
multiplug and illumination bulb Lucar.
18.Disconnect cigar lighter multiplug and
illumination bulb Lucar.
19.Remove centre console assembly.

CHASSIS AND BODY
45
REPAIR Refit
20.Position centre console assembly, ensuring
harnesses and connectors are not trapped and
are routed to their correct locations.
21.Connect cigar lighter multiplug and illumination
bulb Lucar.
22.Align centre console to body fixings and fascia.
23.Fit and tighten screws securing centre console to
body.
24.Lubricate hand brake lever to cable clevis pin.
25.Align hand brake cable to lever, fit clevis pin and
secure with clip.
26.Secure hand brake lever gaiter to centre
console.
Models fitted with electric front seats
27.Position electric front seat switches,connect
multiplugs and secure to centre console.
All models
28.Position centre console switch pack and connect
multiplugs to switches.
29.Align switch pack to centre console and secure
with screws.
30.Fit centre console switch pack cover.
31.Fit centre console rubber mat.
32.Fit gear selector lever knob and secure gaiter.
33.Fit transfer gear lever knob and secure gaiter.
34.Reconnect battery earth lead.DRINKS TRAY
Service repair no - 76.46.41
Remove
1.Disconnect battery negative lead.
2.Remove ash tray.
See ash tray - dash panel
central louvre panel.
3.Remove switch pack.See switch pack - dash
panel central louvre panel.
4.Remove 6 screws securing drinks tray to dash
panel central louvre panel.
5.Remove drinks tray.
Refit
6.Position drinks tray to dash panel central louvre
panel and secure with screws.
7.Fit switch pack.
See switch pack - dash panel
central louvre panel.
8.Fit ash tray.See ash tray - dash panel central
louvre panel.
9.Connect battery negative lead.

CHASSIS AND BODY
59
REPAIR
9.Remove 5 trim studs securing trim panel.
10.Remove trim panel.
Refit
11.Fit and align trim panel.
12.Fit trim panel retaining studs.
13.Position load space cover mounting bracket and
secure with screws.
14.Fold rear seat squab back and secure to latch.
15.Position load space cover to mounting brackets
and secure.
16.Fit 'E' post trim casing.
See 'E' post trim
casing - lh - with rear air conditioning fitted.
17.Fit fold down rear seat belts.See rear fold
down seat belts - lh - with rear air
conditioning fitted.
18.Fit rear fold down seat.See rear fold down
seats.
'E' POST TRIM CASING - RH
Service repair no - 76.13.13/03
Remove
1.Remove rear speaker.
See ELECTRICAL,
Repair, rear speaker.
2.Release 2 'E' post finisher retaining studs from
alpine light trim.
3.Release 2 'E' post finisher retaining clips from
lower trim panel.
4.Remove 'E' post finisher.
Refit
5.Position 'E' post finisher clips to lower trim panel.
6.Secure 'E' post finisher studs to alpine light trim.
7.Fit rear speaker.
See ELECTRICAL, Repair,
rear speaker.