1995 LAND ROVER DISCOVERY light

41TRANSFER GEARBOX
2
REPAIR Remove
1.Site vehicle on a ramp [hoist].
2.Disconnect battery negative lead.
3.Remove fan cowl from radiator.
4.Remove transfer gear lever knob and gaiter.
5.Raise vehicle on ramp [hoist].
6.Drain oil and refit plug.
7.Detach heat shield at front exhaust pipe to
manifold.
8.Disconnect electrics to Lambda sensors.
9.Remove catalytic converter assembly.
10.Remove chassis crossmember from under
gearbox.
11.Remove heat shield from speedometer cable at
transfer gearbox.
12.Remove clamp and disconnect speedometer
cable from transfer gearbox. Tie cable to one
side.
13.Mark for reassembly then disconnect propeller
shaft to output flange, tie to one side.
14.Repeat on front propeller shaft to output flange.
15.Remove bolts retaining silencer front and rear
securing brackets and tie silencer to one side.
16.Place four 30mm long spacers between top of
hoist and adaptor plate, at securing points, and
secure adaptor plate to hoist.17.Remove four central bolts from transfer gearbox
bottom cover, move hoist into position and
secure adaptor plate to transfer gearbox.
18.Adjust hoist to take weight of transfer gearbox.
19.Remove tie bar, transfer gearbox to main
gearbox.
20.Remove nuts and bolts securing right transfer
gearbox mounting bracket to chassis.
21.Repeat for left mounting bracket. Removal of
these fixings will also free speedometer
transducer bracket.
22.Remove right side mounting bracket to flexible
mounting rubber.
23.Lower hoist until rear brake drum clears
passenger footwell. Check engine does not
crush any components while lowering.
24.Loosen park brake adjustment nut.
25.Remove park brake drum.
26.Remove park brake assembly complete from
rear output flange.
27.Disconnect leads from transfer gearbox
temperature sensor and differential lock warning
light switch.
28.Remove banjo bolt from breather pipe, retrieve
sealing washers and lay pipe aside.
29.Remove split [cotter] pin and washers securing
differential lock to connecting rod and disconnect
rod from lever.
30.Select low range transfer gearbox position.
31.Remove high/low rod lower lock nut and remove
rod from yoke.
32.Position hoist jack channel under bell housing.
33.Using wooden block support the main gearbox
and bell housing.
34.Remove upper and lower bolts securing transfer
gearbox to main gearbox.
35.Fit guide studs 18G 1425 to main gearbox and
move transfer gearbox rearwards to detach.

ZF
1
FAULT DIAGNOSIS ZF AUTOMATIC GEARBOX
Before referring to fault symptoms, carry out initial
static checks first:
INITIAL STATIC CHECKS
Check start positions 'P' & 'N' only........................................................
Reverse lights 'R' only..................................................................
Gear engagements N-D,N-3,N-2,N-1,N-R..........................................................
Full throttle Engine switched off, check full travel at engine and at.......................................................................
pedal.
Oil level 'N' selected, engine running at normal running............................................................................
temperature.
Pressure test
2000 rev/min 10±0.3 bar, 150±5 lbf/in
2....................................................................
Idle pressure 6.9±0.3 bar, 100±5 lbf/in2at 665 to 735 rev/min. ....................................................................
To fit pressure gauge
Service tools:
See Service tools, Automatic
Gearbox
0 to 20 bar, 0 to 300 lbf/in2Pressure gauge.
Flexible hose adaptor.
1.Site vehicle on a ramp [hoist].
2.From under gearbox, remove socket head plug
(located 10cm from oil pipe) Fit hose adaptor
LST502-1.
3.Fit hose to adaptor.
4.Fit gauge 18G502A to hose and route into
vehicle, ensuring hose is clear of rotating parts
and exhaust pipes.
5.Carry out road test.
See Road Test Procedure
Remove pressure gauge
6.Reverse removal procedure.

ZF
3
FAULT DIAGNOSIS ROADTEST 3 = CHECKS
12-13-14-15-16-17-18-19-20-21-22-23
D SELECTED FROM REST
LIGHT THROTTLE START
CHECK 12
Check 1st 2nd upshift speed and quality.
CHECK 13
Check 2nd 3rd upshift speed and quality.
CHECK 14
Check 3rd 4th upshift speed and quality.
NOTE: This shift is usually very difficult to
detect but can be confirmed by a 200 rpm
drop in engine speed.
CHECK 15
Check speed and quality of shift into direct drive
clutch, confirmed by 300 rpm drop in engine speed.
NOTE: An intermediate throttle position
engagement of 4th and the direct drive
clutch, which is indicated by a fall of
500rpm in engine speed.
CHECK 16
At approximately 88 kph (55 mph) depress throttle to
kickdown - gearbox should change down to 2nd -
release throttle to re-engage 4th direct drive clutch
continue to accelerate gently.
CHECK 17
At approximately 128 kph (80 mph) depress throttle to
kickdown - gearbox should change down to 3rd -
release throttle to re-engage 4th direct drive clutch
and continue to accelerate gently.CHECK 18
At approximately 138 kph (85 mph) select 3rd,
gearbox should change immediately down to 3rd.
Release throttle.
CHECK 19
De-accelerate to approximately 47 kph (30 mph)
depress throttle to kickdown - geabox should
downshift to 1st gear, continue accelerating at full
throttle until 3rd gear is attained. To do this you will
have repeated check 2 of Test 1.
CHECK 20
At 128 kph (80 mph) select 2nd no downshift should
occur. Release throttle.
CHECK 21
At 104 kph (65 mph) an automatic downshift into 2nd
gear should occur. Continue to de-accelerate.
CHECK 22
At 88 kph (55 mph) select 1st. No downshift should
occur. Continue to de-accelerate.
CHECK 23
With 1 selected 2nd gear engaged continue to
de-accelerate and at 45 kph (28 mph) the box should
automatically downshift to 1st gear after which no
upshifts will occur in this selector position.
END OF ROADTEST

ZF
11
FAULT DIAGNOSIS SYMPTOM 10 - None or harsh engagement of
direct drive clutch
NOTE: The direct drive clutch will only
engage if 4th gear is engaged at 40 to 45
mph.
Carry out road test pressure check with gauge
connected to torque converter.
ú Normal pressure
FAULT - Failed direct drive clutch
ú Pressures correct but remains high
FAULTS POSSIBLE -
Direct drive clutch and torque converter
control valve stuck
Hysteresis valve stuck
Direct drive clutch control valve stuck
SYMPTOM 11 - Direct drive clutch shift point
incorrect or at low speed
NOTE: Direct drive clutch engagement at
low speed will cause vibration in the
torque converter
Carry out mainline and torque converter pressure
check
ú Normal pressure
FAULT - Governor valve sticking
ú Low or incorrect pressure
FAULTS POSSIBLE -
Direct drive clutch and torque converter
control valve sticking.
Hysteresis valve stuck.
Direct drive clutch control valve stuck.
SYMPTOM 12 - Drives in 'D' but immediately
upshifts to 3rd
FAULT - 2nd to 3rd shift valve stuck.
SYMPTOM 13 - With 'D' selected vehicle starts in
2nd
FAULTS POSSIBLE -
1st and 2nd shift valve stuck.
Governor sleeve sticking.
SYMPTOM 14 - With 'D' selected vehicle starts in
3rd
FAULTS POSSIBLE -
1st to 2nd and 2nd to 3rd shift valves stuck.
Governor sleeve sticking.SYMPTOM 15 - No kickdown 4th to 3rd
FAULT - 4th to 3rd kickdown valve stuck.
SYMPTOM 16 - Upshifts/downshifts and kickdown
shifts at incorrect road speeds
Check throttle kickdown cable adjustment
Carry out main line pressure check
ú Normal pressure
FAULT - Governor valve sticking
ú Incorrect pressure
FAULTS POSSIBLE -
Incorrect throttle valve adjustment
Primary regulator sticking
SYMPTOM 17 - No upshifts at light throttle
FAULTS POSSIBLE
Governor valve sticking
Shift valves sticking
SYMPTOM 18 - No engine braking '3' selected 3rd
gear
FAULT - Clutch 'C'
SYMPTOM 19 - Delayed or no downshift occurs
when making a manual selection from '3' to '2'
FAULTS POSSIBLE -
2nd and 3rd upshift valve sticking.
Governor valve sticking.
'2' Position interlock valve sticking.
SYMPTOM 20 - At speeds below 28 mph when
making a manual selection from '2' to '1',
downshift is delayed or does not occur
FAULTS POSSIBLE -
Governor sticking.
1st to 2nd shift valve sticking.
'1' Position interlock valve sticking.
SYMPTOM 21 - '1' Selected 1st gear no engine
braking
FAULT - Clutch brake 3
SYMPTOM 22 - '2' Selected 2nd gear no engine
braking
FAULT - Clutch brake 1
SYMPTOM 23 - Vehicle drives forward in 'N'
FAULT - Clutch 'A' stuck

ZF
3
REPAIR 19.Disconnect rear propeller shaft to output flange,
and tie to one side.
20.Repeat instructions 18 and 19 on front propeller
shaft to main gearbox.
21.Remove bolts retaining silencer front and rear
securing brackets and tie silencer to one side.
22.Disconnect oil cooler feed and return pipes from
bottom and side of main gearbox.
23.Release cooler pipes from clamp at engine sump
and remove distance piece.
24.Blank pipe ends and unions.
25.Move oil cooler pipes clear of transmission and
tie aside.
26.Disconnect selector cable from operating lever.
27.Disconnect inhibitor switch at multiplug.
28.Attach adaptor plate to hoist.
29.Remove two bolts from transfer gearbox rear
cover.
30.Raise hoist to align adaptor plate with transfer
gearbox and transmission. Secure to transfer
gearbox at rear cover with two bolts removed.
31.Adjust hoist to take weight of transmission.
32.Remove nuts and bolts securing right transfer
gearbox mounting bracket to chassis.
33.Repeat for the left mounting bracket. Removal of
these fixings will also free speedometer
transducer bracket
34.Remove right side mounting bracket to flexible
mounting rubber retaining nut.
35.Lower hoist until rear brake drum clears
passenger footwell. Check engine does not
crush any components while lowering.
36.Remove clip and clevis pin from park brake
lever.
37.Remove clip securing outer brake cable
38.The park brake cable is now free.
39.Disconnect leads from transfer gearbox
temperature sensor and differential lock warning
light switch.
40.Remove ties securing breather pipes to harness.
41.Remove bell housing access plate complete with
gasket.
42.Rotate engine, using crankshaft pulley, until two
access holes are visible in drive plate/ring gear
assembly through bell housing bottom cover
opening.
43.Identify an access hole and bolt hole to aid
reassembly.
44.Remove bolts securing drive plate to convertor
through access holes.
45.Rotate crankshaft half turn to access and
remove remaining bolts.
46.Disconnect oil dipstick tube at main gearbox.
47.Remove bolt at bell housing and detach dipstick
tube. Blank pipe end and union.
48.Position hoist jack channel under engine and
support using a wooden block.
49.Remove bell housing to engine securing bolts,
also detach harness bracket from bell housing.
50.Ease transmission rearwards to allow access to
secure torque converter in bell housing.
51.Lower hoist and complete removal of
transmission.
Refit
52.Ensure torque converter is retained in bell
housing.
53.Secure transmission to adaptor plate on lifting
hoist.
54.Raise hoist and locate transmission with engine.
55.Remove torque converter retainer.
56.Complete attachment of transmission to engine
and fit bell housing bolts. Fit the dipstick tube
bracket and harness bracket to their respective
bolts.
57.Complete refitting by reversing removal
procedure. Note the following important points.
58.Drive plate to torque converter bolts are to be
coated with Loctite 290 prior to assembly.
59.Refill transfer and main gearboxes with correct
grade oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids
60.Check operation of parking brake and adjust as
necessary.
See SECTION 10, Maintenance,
Vehicle Interior

44AUTOMATIC GEARBOX
10
REPAIR OIL SCREEN
Service repair no - 44.24.07
Renew
1.Site vehicle on a four post ramp [hoist].
2.Disconnect battery negative lead.
3.Raise vehicle.
4.Drain oil and refit plug with new seal.
5.Detach heat shield at front exhaust pipe to
manifold.
6.Disconnect electrics from Lambda sensors.
7.Remove catalytic converter assembly.
8.Remove chassis cross-member from under
gearbox.
9.Disconnect dipstick tube at oil sump. Loosen
securing bolt at bell housing and move dipstick
aside.
10.Remove clamps securing oil sump. Note their
locations for refit and withdraw sump.
11.Remove gasket and clean gasket mating faces.
12.Remove securing screws and detach oil screen
and suction pipe, taking care to retain suction
pipe spacer, discard 'O' ring seal.13.Detach suction pipe from oil screen, discard 'O'
ring seal.
14.Clean oil screen and blow out with airline.
15.Clean suction pipe.
16.Fit new 'O' ring seals to oil screen using light
grease to aid assembly.
17.Fit oil screen and suction pipe with spacer and
secure with three bolts.
18.Refit oil sump using a new gasket.
19.Connect dipstick tube to oil sump and tighten
bolt at bell housing.
20.Refit chassis cross-member.
21.Refit catalytic converter assembly
22.Connect electrics to Lambda sensors.
23.Connect heat shield front pipe to manifold.
24.Connect battery.
25.Refill gearbox oil system using correct grade of
oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids

44AUTOMATIC GEARBOX
12
REPAIR Oil seal replacement
14.Remove circlips and springs from control unit.
Note locations of long and short springs.
15.Using seal replacer/remover LST113 remove
and discard seals.
16.Clean control unit, springs and circlips and check
that they are satisfactory for further use.
17.Fit new seals to control unit using LST113,
ensure seals are fully seated.
18.Fit springs to locations noted during removal and
secure with circlips.
Refit
19.Fit control unit to gearbox, locating throttle valve
behind cam and engaging selector quadrant with
manual valve.
20.Loosely fit securing screws.21.Manually open throttle linkage to full throttle
position.
22.Engage special tool LST 109 between control
unit and throttle valve pin.
23.Set correct distance between control unit and
cam.
24.Remove special tool and close throttle.
25.Fit new 'O' ring seals to oil screen using light
grease to aid assembly.
26.Fit oil screen and suction pipe with spacer and
secure with three bolts.
27.Refit oil pan using a new gasket.
28.Connect dipstick tube to oil sump and tighten
bolt at bell housing.
29.Refit chassis cross member.
30.Refit catalytic converter assembly
31.Connect electrics to Lambda sensors.
32.Connect heat shield front pipe to manifold.
33.Connect battery.
34.Refill gearbox oil system using correct grade of
oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids

ZF
19
REPAIR 6.Screw in two bolts, diagonally opposite each
other. Tap lightly using a soft headed mallet to
remove pump assembly from intermediate plate.
7.Remove shaft sealing ring and 'O' ring from
pump housing and discard.
8.Using oil seal replacer LST108 fit shaft seal ring
into pump housing.
9.Fit 'O' ring onto circumference of pump housing.
10.Align dowel with hole in intermediate plate and
press pump housing home.11.Fit pump housing to intermediate plate, tighten
eight bolts to
10 Nm.
12.Place bell housing and intermediate plate
assembly on bench, front face up. Using oil
pump rotation sleeve LST111, check that pump
gears rotate freely.
13.Before fitting intermediate plate and bell housing
assembly,check that thrust washer and axial
cage are seated on A clutch housing.
14.Place gasket and disc washer onto bell housing
and intermediate plate assembly using
Petroleum Jelly.
15.Fit bell housing and intermediate plate assembly
to gearcase. Tighten twelve bolts to
46 Nm.
16.Place end float gauge LST111 onto pump
housing and check that axial play is between
0.2-0.4 mm. Replace existing washer, situated at
rear of intermediate plate, with a suitable washer
to give required end float.
17.Refit torque converter into housing using torque
converter handles 18G1501, checking that
dimension from converter fixing bolt boss to
converter housing face is 50 mm. This shows
converter is properly seated in housing.
18.Refit gearbox/transfer box assembly.
See
LT230T Transfer Gearbox