1995 LAND ROVER DISCOVERY sensor

12ENGINE
8
REPAIR
9.Disconnect multiplug from camshaft sensor.
See FUEL SYSTEM SFI, Repair, Camshaft
Position Sensor (CMP Sensor)
10.Remove 9 bolts securing front cover.
11.Remove 2 bolts securing sump to front cover.
12.Loosen 4 bolts securing sump adjacent to front
cover (2 each side).
13.Release front cover assembly.
14.Remove oil seal.
15.Remove and discard gasket.Refit
16.Clean sealant from threads of cover bolts.
17.Clean old sealant from front cover and block joint
face.
CAUTION: Use a plastic scraper.
18.Apply Hylosil jointing compound to gasket
position on cover and block.
19.Fit new gasket to block face.
20.Ensure oil seal register in cover is clean.
21.Lubricate outer face of NEW oil seal.
22.Using LRT-12-089, fit seal to cover.
23.Lubricate oil pump drive gear and position in
pump with groove away from engine.
24.Locate alignment tool LRT-12-090 on front cover
and oil pump drive gear.
25.Position front cover over crankshaft.
26.Press and rotate tool to engage drive gear until
drive gear keyway aligns with Woodruff key.
27.Fit cover to cylinder block.

4.0 V8
9
REPAIR 28.Remove alignment tool LRT-12-090.
29.Apply a small amount of Loctite 242 to threads
and refit front cover bolts. Tighten to
22 Nm.
30.Fit sump bolts. Tighten to23 Nm.
31.Connect camshaft sensor multiplug.
32.Connect Lucar to oil pressure switch terminal.
33.Remove plugs from oil cooler pipes and cover.
34.Fit new 'O' ring seals, reconnect oil cooler pipes.
Tighten to
15 Nm.
CAUTION: Over tightening of oil cooler
pipe unions can crack front cover.
35.Refit bottom hose to water pump. Tighten clip.
36.Refit water pump pulley.
See COOLING
SYSTEM, Repair, Viscous Coupling, Fan
Blades, Pulley and Fan Cowl
37.Refit radiator assembly.See COOLING
SYSTEM, Repair, Radiator
38.Refill cooling system.See COOLING SYSTEM
V8, Adjustment, Coolant
39.Check/top-up engine oil.
40.Lower ramp.
41.Reconnect battery negative lead.

Mpi
3
DESCRIPTION AND OPERATION Lubrication
Oil is drawn from the pressed steel sump through a
strainer (1) and into the oil pump (2); excess pressure
being relieved by a pressure relief valve (3) integral
with the pump. The low oil pressure sensor (4)
registers the oil pressure in the main oil gallery on the
outflow side of the filter. Pressurised oil passes
through the full flow oil filter (5) to internal drillings in
the crankshaft where it is directed to each main
bearing and to the big end bearings via Nos. 1, 3 and
5 main bearings (6). An internal drilling in the cylinder
block directs oil, via a restrictor (7) to the cylinder
head where it passes through further internal drillings
to the hydraulic tappets and camshaft journals (8).
Gudgeon pin and small-end bush lubrication is by
splash from the big-end bearings.Crankcase ventilation
With the exception of two hoses connected from the
inlet camshaft cover to the inlet manifold and throttle
housing all crankcase ventilation is via internal voids
in the cylinder head and block. The inlet camshaft
cover carries a wire gauze flame trap located over the
breather pipe connections.

12ENGINE
4
DESCRIPTION AND OPERATION CYLINDER BLOCK COMPONENTS
1. Cylinder block
2. Knock sensor
3. Crankshaft sensor
4. Bolt - crankshaft sensor
5. Locating dowel - cylinder head
6. Bolt - connecting rod
7. Piston
8. Piston ring - top compression
9. Piston ring - 2nd compression
10. Piston ring - oil control
11. Gearbox adapter plate
12. Bearing shell - big end - upper
13. Flywheel
14. Bolt - flywheel
15. Torx screw - gearbox adapter plate
16. Blanking plate
17. Bolt - blanking plate
18. Gasket
19. Bolt - crankshaft rear oil seal housing
20. Crankshaft rear oil seal and housing
21. Bolt - coolant pump cover
22. Coolant pump cover
23. Impeller
24. Sealing rings
25. 'O' ring
26. Bolts - coolant pump
27. 'O' ring
28. Coolant pump body
29. Thrust washer halves - upper
30. Bearing shell - main bearing - upper
31. Locating dowel - oil pump
32. Locating dowel - flywheel
33. Gudgeon pin34. Crankshaft
35. Bearing shell - big end - lower
36. Bearing cap - big end
37. Nut - big end bearing cap
38. Locating dowel - main bearing cap
39. Bearing caps - main bearings
40. Bolt - main bearing cap
41. Thrust washer halves - lower
42. Bearing shell - main bearing - lower
43. Woodruff keys
44. Dipstick
45. Bolt - dipstick tube
46. Dipstick tube
47. Bolts - sump
48. Gasket - sump
49. 'O' ring
50. Oil strainer
51. Bolts - oil strainer
52. Sump
53. Washer - drain plug
54. Drain plug
55. Oil filter element
56. Crankshaft front oil seal
57. Bolts - oil pump
58. Gasket - oil pump
59. Oil pump
60. Oil pressure switch
61. Crankshaft spigot bush
62. Crankshaft spigot bearing
63. Locating dowel - coolant pump
64. Connecting rod
65. Bolts belt tensioner mounting plate
66. Belt tensioner mounting plate
67. Bolt - gearbox adapter plate

12ENGINE
6
DESCRIPTION AND OPERATION CYLINDER HEAD COMPONENTS
1. Engine oil filler cap
2. Filler cap seal
3. Screw - spark plug cover
4. Spark plug cover
5. h.t. lead plate
6. Screw - h.t. lead plate
7. Inlet camshaft cover
8. Exhaust camshaft cover
9. Bolt - exhaust camshaft cover
10. Exhaust camshaft cover gasket/baffle plate
11. Bolt - exhaust camshaft carrier
12. Exhaust camshaft carrier
13. Exhaust camshaft
14. Cylinder head bolt
15. Blanking plate
16. Bolt - blanking plate
17. Locating dowel - camshaft carrier
18. Coolant outlet elbow
19. Gasket
20. Bolt - coolant outlet elbow
21. Stud - exhaust manifold
22. Cylinder head gasket
23. Guide - exhaust valve24. Insert - exhaust valve seat
25. Exhaust valves
26. Inlet valves
27. Insert - inlet valve seat
28. Guide - inlet valve
29. Cylinder head
30. Stud - inlet manifold
31. Valve stem oil seal
32. Valve spring
33. Valve spring cap
34. Collets
35. Tappet
36. Camshaft oil seals
37. Drive pins - camshaft timing gears
38. Inlet camshaft
39. Inlet camshaft carrier
40. Bolt - inlet camshaft carrier
41. Inlet camshaft cover gasket/baffle plate
42. Bolt - inlet camshaft cover
43. Spark plug
44. Coolant temperature sensor
NOTE: Items 15,16 & 36 on current engines
replaced by an oil plug.
See Repair, Inlet -
Exhaust Camshaft Rear Oil Plug

Mpi
7
REPAIR
NOTE: On current models the generator
cover is omitted.
9.Remove 3 nuts securing generator rear cover.
10.Remove rear cover.
11.Remove 3 nuts securing harness to generator.
12.Remove harness.
13.Disconnect oxygen sensor multiplug.
14.Release multiplug from bracket.
15.Release harness from cable tie.
16.Disconnect 2 coolant temperature sensor
multiplugs.
17.Release clips and disconnect the bypass and
top hose.
18.Release harness lead from cable tie.
19.Release clip and disconnect breather hose from
inlet manifold.
20.Feed harness between inlet manifold and cam
cover.

12ENGINE
8
REPAIR 21.Release clip and disconnect inlet hose from
power steering pump.
22.Disconnect outlet pipe union at power steering
pump, discard 'O' ring.
CAUTION: Plug the connections
23.Release throttle cable from abutment bracket.
24.Release throttle cable from cam. Also remove
coolant bypass hose from throttle housing.
25.Disconnect stepper motor and throttle
potentiometer multiplugs.
26.Release clip and disconnect hose, air cleaner to
throttle housing.
27.Release clip and disconnect brake servo hose
from manifold.
28.Disconnect fuel temperature sensor multiplug.

Mpi
9
REPAIR 29.Disconnect oil pressure switch multiplug.
30.Disconnect air conditioning compressor
multiplug.
31.Remove 3 bolts securing engine harness to
manifold and fuel pipe.
32.Disconnect knock sensor multiplug.
33.Remove 2 nuts securing harness to starter motor
solenoid, remove harness.
34.Disconnect crankshaft sensor multiplug.
35.Disconnect fuel injection harness multiplug.
36.Disconnect inlet manifold air temperature sensor
multiplug.
37.Release clip and disconnect fuel hose from
pressure regulator.
CAUTION: Plug the connections.