1995 LAND ROVER DISCOVERY sensor

LUBRICANTS, FLUIDS AND CAPACITIES
5
INFORMATION ANTI-FREEZE
ENGINE TYPE MIXTURE STRENGTH PERCENTAGE PROTECTION
CONCENTRATION LOWER
TEMPERATURE
LIMIT
V8i Engine One part anti-freeze
Diesel Engine One part water 50%
Complete protection-33°F
Vehicle may be driven away immediately from cold - 36°C
Safe limit protection-41°C
Coolant in mushy state. Engine may be started and driven away after warm-up
period-42°F
Lower protection-47°C
Prevents frost damage to cylinder head, block and radiator. Thaw out before
starting engine-53°F
CAUTION: Anti-freeze content must never be allowed to fall below 25% otherwise damage to the
engine is liable to occur. Also, anti-freeze content should not exceed 60% as this will greatly
reduce the cooling effect of the coolant.
FUEL REQUIREMENTS
Catalyst vehicles
Vehicles equipped with catalytic converter are designed to use ONLY unleaded fuel. Unleaded fuel must be used
for the emission control system to operate properly. Its use will also reduce spark plug fouling, exhaust system
corrosion and engine oil deterioration.
Using fuel that contains lead will result in damage to the emission control system and could result in loss of
warranty coverage. The effectiveness of the catalysts in the catalytic converters will be seriously impaired if leaded
fuel is used. The vehicle is equipped with an electronic fuel injection system, which includes two oxygen sensors.
Leaded fuel will damage the sensors, and will deteriorate the emission control system.
Regulations require that pumps delivering unleaded fuel be labelledUNLEADED.Only these pumps have nozzles
which fit the filler neck of the vehicle fuel tank.

10MAINTENANCE
18
MAINTENANCE
ABS VEHICLES - CHECK ROAD WHEEL SPEED
SENSOR ELECTRICAL HARNESS FOR DAMAGE
RENEW OXYGEN SENSORS
See EMISSION CONTROL, Repair, Heated
Oxygen Sensor (HO2S)
RENEW CATALYTIC CONVERTERS
See MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust System Complete
REPORT ANY UNUSUAL FEATURES OF VEHICLE
CONDITION AND ADDITIONAL WORK REQUIREDCARRY OUT ROAD TEST
For details of dynamometer testing.See
INTRODUCTION, Information, Dynamometer
Testing - Non Anti-lock brake vehicles See
INTRODUCTION, Information, Dynamometer
Testing - Vehicles with Anti-lock brakes (ABS)
Check following items:
1.Inhibitor switch only operates in P and N.
2.Engine for excessive noise.
3.Clutch for slip, judder or spin.
4.Automatic gear selection/shift speeds.
5.Gear selection/noise - high/low range.
6.Steering for abnormal noise/effort.
7.Steering for free play.
8.All instruments, gauges and warning indicators.
9.Heater and air conditioning systems.
10.Heated rear screen.
11.Shock absorbers - ride irregularities.
12.Foot brake, on emergency stop, pulling to one
side, binding, pedal effort.
13.Parkbrake efficiency.
14.Seat reclining and latching.
15.Fully extend seat belt, check operation of
retraction and latching. Inertia belts lock when
snatched or vehicle on slope.
16.Road wheel balance.
17.Transmission for vibrations.
18.Body noises, squeaks and rattles.
19.Excessive exhaust smoke.
20.Engine idle speed.
21.Endorse service record.
22.Report any unusual features of vehicle condition
and additional work required.
ENDORSE SERVICE RECORD

MAINTENANCE
19
MAINTENANCE
RESET EMISSION MAINTENANCE REMINDER -
USA
The emission maintenance reminder is designed to
activate at 52,500 and 105,000 miles respectively and
will illuminate a 'Service Engine' red warning light in
instrument binnacle.
The emission maintenance reminder must be reset
after required maintenance has been carried out and
a new tamperproof label fitted by a Land Rover of
North America dealer. This emission maintenance
reminder is part of the Emission Control System
Reset
1.The control unit is located in the passenger
footwell.
2.Identify control unit and remove from plug.
3.Remove tamperproof label to reveal access hole
for resetting.
4.Place a thin metallic probe into access hole and
momentarily electrically short between reset pins
inside unit.RECOMMENDED SERVICE ITEMS
Refer Service Schedule sheets for intervals.
Clean sunroof drain tubes, clean and lubricate guide
rails and slides.
Renew the hydraulic brake fluid.
See BRAKES,
Repair, Brake System Bleed
Renew all hydraulic brake fluid, seals, brake servo
filter and flexible hoses.
All working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.
ABS vehicles only - renew hydraulic brake fluid and
flexible hoses examine the working surfaces of the
caliper cylinders and renew the seals or cylinders
where necessary.
Air cleaner - When the vehicle is used in dusty or field
conditions or deep wading, frequent attention to the
air cleaner may be required.
ABS vehicles used extensively in arduous off-road
conditions - check the rear wheel road speed sensor
for abrasive wear.

12ENGINE
20
REPAIR CYLINDER HEAD GASKET
Service repair no - 12.29.02
Remove
1.Disconnect battery negative lead.
2.Remove bonnet [Hood].
See CHASSIS AND
BODY, Repair, Bonnet [Hood]
3.Drain coolant.
4.Remove air cleaner assembly.
See FUEL
SYSTEM, Repair, Air Cleaner
5.Detach crankcase ventilation valve and side
breather hose from rocker cover and move to
one side.
6.Remove injection pipes.
7.Disconnect spill rail from fuel injectors.
8.Remove fuel injectors and sealing washers.
Identify each injector to the location from which it
is removed.
See FUEL SYSTEM, Repair,
Injectors
9.Remove inter-connecting harness from glow
plugs.
10.Remove glow plugs.
See FUEL SYSTEM,
Repair, Glow Plugs
11.Remove top hose, radiator to thermostat.
12.Disconnect by-pass hose from thermostat.
13.Disconnect hose, thermostat to water pump.
14.Disconnect water temperature sensor lead.
15.Remove hose inter-cooler to induction manifold.
16.Remove induction manifold.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
Manifold - Tdi
17.Remove exhaust manifold and turbocharger
assembly.
See MANIFOLD AND EXHAUST
SYSTEM, Repair, Exhaust Manifold - Tdi
18.Disconnect heater hose from water pump and
move heater rail aside.
19.Disconnect heater hose from rear of cylinder
head.
20.Remove bolt securing air cleaner mounting
bracket to support strut.
21.Remove bolt securing harness bracket to
cylinder head.
22.Remove rear lifting bracket, this will also release
clips securing transmission and engine breather
pipes and multiplug. Note loose spacer under
clip securing engine breather pipe and multiplug.

12ENGINE
2
SPECIFICATIONS, TORQUECylinder head
Cylinder head to cylinder block See repair section......................................................
Stub pipe heater feed 22.................................................................................
Water temperature sensor 14.........................................................................
Blanking plug cylinder head 14.......................................................................
Engine lifting brackets 25................................................................................
Electrical harness clip bracket 25...................................................................
Exhaust manifold stud 10................................................................................
Exhaust manifold nut 45.................................................................................
Inlet manifold stud 8.......................................................................................
Inlet manifold nut and bolt 25..........................................................................
Air temperature sensor, inlet manifold 14.......................................................
Blanking plug, inlet manifold 14......................................................................
Heatshield to inlet manifold 6.........................................................................
Glow plug 20...................................................................................................
Glow plug terminal nut 2................................................................................
Injector clamp (stud) 8...................................................................................
Injector clamp (nut) 25....................................................................................
Thermostat housing 25...................................................................................
Water outlet elbow to thermostat housing 25..................................................
Water temperature switch, thermostat housing 11..........................................
Plug thermostat housing 6.............................................................................
Rocker shaft pedestal bolt 5 + 50° .....................................................................
Rocker cover (stud) 8.....................................................................................
Rocker cover (fixing nut) 10............................................................................
Breather cyclone to rocker cover 9................................................................
Tappet adjusting nut 16..................................................................................
Front cover to cylinder block 25......................................................................
Front cover plate to front cover 25..................................................................
Static idler - timing belt (stud) 10.....................................................................
Static idler - timing belt (nut) 45......................................................................
Tensioner (timing belt) 45...............................................................................
Camshaft hub bolt 80......................................................................................
Timing pulley to camshaft hub 25...................................................................
Fuel injection pump (stud) 8...........................................................................
Fuel injection pump (nut) 25...........................................................................
Abutment bracket to injection pump 25...........................................................
Support bracket injection pump to cylinder block 25.......................................
Fuel injection pump access plte to front cover plate 25..................................
Timing pulley to injection pump hub 25...........................................................
TV Damper pulley bolt to crankshaft 80 + 90° .....................................................
Fan pulley to hub 25.......................................................................................
Fan and viscous coupling to hub 45...............................................................
Auto tensioner, auxiliary drive (stud) 14..........................................................
Auto tensioner, auxiliary drive (nut) 45...........................................................
Auxiliary mounting bracket to cylinder block (stud) 8.....................................
Auxiliary mounting bracket to cylinder block (bolt and nut) 25........................
Water pump to block and mounting plate 25..................................................
Water pump pulley to hub 25..........................................................................

Tdi
3
SPECIFICATIONS, TORQUE Turbo charger oil drain adaptor to block 42....................................................
Oil drain pipe to turbocharger 25....................................................................
Turbocharger oil drain pipe to adaptor 38.......................................................
Turbocharger oil feed pipe adaptor to block 25...............................................
Turbocharger oil feed pipe to adaptor 25........................................................
Oil feed pipe to turbocharger 19.....................................................................
Turbocharger to cylinder head (stud) 10.........................................................
Turbocharger to cylinder head (nut) 45...........................................................
Turbocharger to blanking plate 25..................................................................
Turbocharger to EGR valve 25.......................................................................
EGR delivery tube to valve 25........................................................................
EGR delivery tube to mixing tube 25..............................................................
Fuel lift pump to filter (union) 15.....................................................................
Fuel filter from lift pump (banjo bolt) 33...........................................................
Fuel filter to fuel injection pump (banjo bolt) 33..............................................
Fuel injection pump from fuel filter (banjo bolt) 25..........................................
Injector pipes to injectors and fuel injection pump 29.....................................
Spill rail to injectors (banjo bolt) 10.................................................................
Spill rail to injection pump (banjo bolt) 25.......................................................
Boost pipe injection pump (banjo bolt) 10.......................................................
Plug, rear of injection pump 29.......................................................................
PAS pump to mounting plate 25.....................................................................
PAS pump mounting plate to auxiliaries mounting bracket 25........................
PAS pump pulley to hub 25............................................................................
Generator to auxiliaries mounting bracket 25.................................................
Starter motor (bolt and nut) 45........................................................................
Tachometer electrical connection 4...............................................................
Air conditioning compressor
Compressor mounting bracket to front cover 45.............................................
Compressor to mounting bracket (stud) 8......................................................
Compressor to mounting bracket (nut) 25......................................................
Belt tensioner pulley to tensioner arm 45........................................................
Belt tensioner assembly to front cover plate 25..............................................
Idler pulley to front cover plate 45...................................................................
Compressor belt guard (nut) 25......................................................................
Sensors to water outlet elbow (air/con) 25......................................................
Blanking plug, water outlet elbow (air/con) 25................................................
Generator mounting bracket to front cover 45................................................
Generator to mounting bracket 85..................................................................
Generator pulley to hub 95.............................................................................
Generator belt guard 25..................................................................................

12ENGINE
4
REPAIR CYLINDER HEAD GASKETS - RENEW
Service repair no - 12.29.01
1.Drain cooling system.
See COOLING SYSTEM,
Adjustment, Coolant
2.Remove inlet manifold.See FUEL SYSTEM,
Repair, Intake Manifold
3.Remove generator.
4.If fitted, remove compressor.
See AIR
CONDITIONING, Repair, Compressor
5.Remove rocker shafts.See Rocker Shaft
Renew
6.Remove push rods.
7.Remove both exhaust manifolds.
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust Manifold - V8i
8.Remove air cleaner assembly.See FUEL
SYSTEM, Repair, Air Cleaner Assembly
9.Remove air flow sensor.See FUEL SYSTEM,
Repair, Air Flow Sensor
10.Remove ground leads from rear of left hand
cylinder head
11.Right hand cylinder head - remove breather pipe
from lifting bracket.
12.Loosen cylinder head bolts, reversing tightening
sequence.
13.Remove cylinder heads.
14.Remove cylinder head gaskets.
15.Clean exhaust mating faces.
16.Clean head and block faces.
17.Fit new cylinder head gaskets, word TOP
uppermost. DO NOT use sealant.
18.Oil cylinder bores.
19.Clean threads of head bolts and lightly oil.
20.Locate cylinder heads on block.
21.Locate cylinder head bolts in position illustrated.
96 mm long bolts - 2, 4, 6, 7, 8, 9, 10
66 mm long bolts - 1, 3, 5
NOTE: There are no bolts fitted in the four
lower holes in each cylinder head.
NOTE: Left hand cylinder head illustrated,
arrow points to front of vehicle.
22.Tighten bolts progressively in sequence, shown
to
20 Nmthen a further 180°±5°
23.Reverse removal procedure. 1 to 11.

12ENGINE
6
REPAIR 11.Place one end of gasket into cover recess with
edge firmly against recess wall, holding
remainder of gasket clear. Work around cover,
pressing gasket into place ensuring edge firmly
contacts recess wall.
12.Allow cover to stand for thirty minutes before
fitting.
13.Fit rocker cover to cylinder head with four
screws, short screws inboard, tighten to
9 Nm.
14.Position fuel pipes.
15.Fit breather pipe to rocker cover, tighten clip.
16.Fit coolant pipes to inlet manifold, tighten bolts.
17.Fit spark plug leads to plugs and retaining clips.
18.Connect purge pipe from charcoal canister at
plenum, tighten clip.
ROCKER COVER - LEFT HAND - RENEW
Service repair no - 12.29.40
1.Remove air flow sensor.
See FUEL SYSTEM,
Repair, Air Flow Sensor
2.Remove plenum chamber.See FUEL SYSTEM,
Repair, Plenum Chamber
3.Remove dipstick.
4.Remove spark plug leads from plugs and
retaining clips.
5.Disconnect HT lead from coil.
6.Remove generator heat shield securing nut from
rocker cover.
7.Remove air flow meter harness clip.
8.Remove bolt securing dipstick tube clip.
9.Remove four rocker cover bolts, remove rocker
cover.
10.Discard gasket
11.Remove plug lead retaining clips from rocker
cover, fit to new rocker cover.
12.Clean and dry rocker cover and cylinder head
mating faces, using Bostik cleaner 6001.
NOTE: Gasket fits one way round only. It
must be fitted accurately, first time.
Subsequent movement will destroy
bonding.
13.Apply Bostik 1775 impact adhesive to rocker
cover seal face and gasket, using a brush to
ensure an even film. Allow adhesive to become
touch dry, approximately fifteen minutes.
14.Place one end of gasket into cover recess with
edge firmly against recess wall, holding
remainder of gasket clear. Work around cover,
pressing gasket into place ensuring edge firmly
contacts recess wall.
15.Allow cover to stand for thirty minutes before
fitting.
16.Fit rocker cover to cylinder head with four
screws, short screws inboard. Tighten to
9 Nm.
17.Position dipstick tube clip. Fit and tighten bolts.
18.Fit and tighten air flow meter harness clip.
19.Fit generator heat shield to rocker cover.
20.Connect HT lead to coil.
21.Connect spark plug leads to plugs and retaining
clips.
22.Fit dipstick.
23.Fit plenum chamber.
24.Fit air flow meter.