1995 LAND ROVER DISCOVERY belt

V8i
3
REPAIR DRIVE BELT TENSIONER
Service repair no - 86.10.09
Remove
1.Remove drive belt from tensioner.
See Drive
Belt Renew
2.Loosen tensioner centre bolt.
3.Remove bolt and tensioner.
Refit
4.Reverse removal procedure.

12ENGINE
8
REPAIR CRANKSHAFT PULLEY ASSEMBLY
Service repair no - 12.21.01
1.Remove viscous coupling.
See COOLING
SYSTEM, Repair, Viscous Coupling, Fan
Blades, Pulley and Fan Cowl
2.Remove drive belt.See Drive Belt
3.Raise vehicle on ramp [hoist].
4.Remove bell housing bottom cover.
5.Remove engine undertray.
6.With assistance to stop flywheel rotation, remove
crankshaft pulley assembly retaining bolt.
7.Remove crankshaft pulley assembly.
8.If required: Place assembly in vice and remove
pulley.
9.Fit pulley to torsional vibration damper.
10.Lubricate seal face of assembly.
11.Fit pulley assembly.
12.With assistance to stop flywheel rotation, fit
retaining bolt. Tighten to
280 Nm.
13.Reverse removal procedure. 1 to 5.FRONT COVER OIL SEAL - RENEW
Service repair no - 12.21.14
1.Remove crankshaft pulley.
See Crankshaft
Pulley Assembly. Do not remove pulleys.
2.Remove eight screws and remove mud
excluder.
3.Fit button of 18G1328 to crankshaft, fit extractor
to seal.
4.Turn centre bolt of extractor to remove seal.
5.Remove seal from extractor.
6.Clean seal seating.
7.Lubricate outside diameter of seal.
8.Locate seal in front cover.
9.Fit adaptor 18G1291/5 to 18G1291/4.
10.Fit tool to seal.
11.Fit and tighten centre bolt to crankshaft, tighten
centre locknut to seat seal.
12.Slacken locknut and remove tool.
13.Lubricate seal lip.
14.Fit mud excluder and tighten screws.
15.Fit crankshaft pulley assembly.

V8i
9
REPAIR FRONT COVER GASKET
Service repair no - 12.65.04
1.Remove crankshaft pulley.
See Crankshaft
Pulley Assembly. Do not remove pulleys
2.Remove water pump pulley.
3.Release distributor cap clips.
4.Release plug leads from plugs and clips.
5.Place cap and leads to one side.
6.Turn engine until No. 1 piston is at T.D.C.
7.Check position of rotor arm.
8.Remove fixings securing power steering pump
bracket to water pump bracket.
9.Remove power steering pump bracket from
water pump.
10.Remove clips securing wiring to generator
tensioner.
11.Disconnect distributor feed wire.
12.Pivot power steering pump away from front
cover, tighten pivot to retain in position.
13.Disconnect vacuum pipe from distributor.
14.Remove water pump bottom hose.
15.Disconnect oil pressure switch.
16.Disconnect heater hose at water pump.
17.Remove generator tensioner from water pump,
move tensioner aside.
18.Mark distributor position to front cover.
19.Remove distributor clamp, remove distributor.
See ELECTRICAL, Repair, Distributor - V8i
20.Remove fixings sump to front cover.
21.Loosen four adjacent sump fixings.
22.Remove generator support strut from front cover,
move strut aside.
23.Loosen remaining front cover fixings and remove
front cover.
24.Remove front cover gasket.Refit
25.Clean timing cover, clean block face.
26.Lightly grease gasket faces.
27.Fit new gasket to block face.
28.Apply hylosil to sump gasket.
29.Clean threads of cover fixing bolts, apply Loctite
372 to threads.
30.Fit timing cover, fit fixing bolts. Tighten to
28
Nm.
31.Fit generator support strut to front cover.
32.Tighten sump to timing cover fixings to
10 Nm.
33.Tighten sump fixings to10 Nm.
34.Lubricate distributor O ring.
35.Fit distributor in position marked.
36.Align oil pump drive, if distributor does not seat
correctly.
37.Fit distributor clamp. Tighten to
20 Nm.
38.Locate generator tensioner on water pump
bracket.
39.Connect heater hose, tighten clip.
40.Connect oil pressure switch.
41.Connect bottom hose, tighten clip.
42.Connect vacuum pipe to distributor.
43.Loosen power steering pump pivot, lower pump.
44.Connect distributor feed wire.
45.Connect wire ties to generator tensioner.
46.Fit power steering pump bracket to water pump.
Tighten to
28 Nm.
47.Fit power steering pump to bracket.
48.Position distributor cap. Fit plug leads to plugs
and clips.
49.Clip distributor cap in position.
50.Fit water pump pulley. Tighten to
10 Nm.
51.Fit crankshaft pulley.See Crankshaft Pulley
Assembly
52.Tension drive belts correctly.
53.Check ignition timing.
54.Refill cooling system.

4.0 V8
1
REPAIR CRANKSHAFT PULLEY
Service repair no - 12.21.01 - Crankshaft Pulley
Remove
1.Disconnect battery negative lead.
2.Remove cooling fan.
See COOLING SYSTEM,
Repair, Viscous Coupling, Fan Blades,
Pulley and Fan Cowl
3.Slacken 3 water pump pulley securing bolts.
4.Remove drive belt.
See ENGINE 3.9 V8,
Repair, Drive Belt Renew
5.Remove water pump pulley bolts. Remove water
pump pulley.
6.Raise and support front of vehicle.
7.Remove 9 bolts securing bell housing access
cover (2 dowel bolts).
8.Remove access plate.
NOTE: It will be necessary to have an
assistant position a large flat ended
screwdriver between ring gear and adaptor
plate to prevent ring gear rotating.
9.Remove crankshaft pulley bolt. Collect pulley
and tool.
Refit
10.Clean seal running surface on pulley.
11.Clean key and keyway.
12.Fit crankshaft pulley.
NOTE: It will be necessary to have an
assistant position a large flat ended
screwdriver between ring gear and adaptor
plate to prevent ring gear rotating.
13.Refit crankshaft pulley bolt. Tighten to
270 Nm.
14.Ensure mating faces between bell housing
access cover and mating face are clean.
15.Fit access cover.
16.Fit cover bolts. Tighten to
10 Nm.
17.Remove supports and lower vehicle.
18.Ensure mating faces between water pump pulley
and pump are clean.
19.Refit water pump pulley. Fit bolts finger tight.
20.Fit drive belt.
See ENGINE 3.9 V8, Repair,
Drive Belt Renew
21.Tighten water pump pulley bolts to Tighten to24
Nm.
22.Refit cooling fan.See COOLING SYSTEM,
Repair, Viscous Coupling, Fan Blades,
Pulley and Fan Cowl
23.Reconnect battery negative lead.

12ENGINE
4
REPAIR 39.Release battery positive lead terminal cover.
40.Remove terminal nut
41.Release terminal from battery.
42.Release fusebox main feed lead.
43.Position battery cable over engine.
44.Pivot jockey pulley downwards to release drive
belt tension.
45.Release belt from pulleys.
46.Remove drive belt.
47.Disconnect compressor multiplug
48.Remove 4 bolts securing compressor.
49.Remove heatshield.
50.Release compressor from bracket and tie aside.
51.Slacken clip securing PAS hose to pump.
52.Disconnect hose.
53.Plug hose and pump.
54.Disconnect PAS hose connection at pump and
steering box.
55.Release unions and remove hose.
56.Remove and discard 'O' rings.
57.Plug pump and steering box.
58.Remove LH and RH engine mounting nuts.
59.Position lifting chains and attach hooks to engine
lifting eyes.
60.Raise engine sufficiently to release engine
mountings.
61.Release engine mountings and remove.
62.Lower engine until it just rests on engine
mounting brackets.
63.Disconnect chains.
64.Raise ramp.
65.Remove catalytic converter/front pipe assembly.
See EMISSION CONTROL, Repair, Catalytic
Converter/Front Pipe - 4.0 V8
66.Remove 9 bolts securing bell housing bottom
cover. Note position of 2 dowel bolts.
67.Remove cover.
68.Remove locknut securing transfer box tie bar.
69.Remove 2 bolts securing tie bar to tranmission.
70.Remove tie bar.
71.Remove 2 and slacken 1 bolt, securing bell
housing access plate and position aside.
72.Mark drive plate to torque converter relationship.
73.With assistance, rotate crankshaft for access to
first bolt (torque converter to drive plate).
74.Remove first bolt.
75.Repeat steps for the remaining 3 bolts.
76.Remove 2 bolts securing crankshaft sensor
shield to engine backplate.
See FUEL SYSTEM
SFI, Repair, Crankshaft Position Sensor
(CKP Sensor)

12ENGINE
6
REPAIR
106.Remove top starter bolt securing engine earth
cable.
107.Remove nut securing kick-down cable clip to LH
cylinder head.
108.With assistance, raise engine, move aside all
pipes and wires. Move engine clear of vehicle.
109.Lower engine onto bench.
Refit
110.Clean engine and gearbox mating faces.
111.Clean dowel and dowel holes.
112.With assistance raise engine off bench. Lower
and guide engine into engine compartment
ensuring no wires or pipes become trapped.
113.Position clip securing kick-down cable to LH
cylinder head.
114.Fit and tighten nut.
115.Position engine earth cable and secure to starter
with top bolt. Tighten to
45 Nm.
116.Lower engine.
117.With assistance, engage engine with gearbox.
118.Fit 3 bottom bell housing bolts. Tighten to
46
Nm.
119.Lower jack supporting gearbox.
120.Lower engine onto mounting brackets.
121.Fit centre RH bell housing bolt.
122.Fit centre LH bell housing bolt.
123.Fit harness brackets to 2 top bell housing bolts.
124.Fit bolts. Tighten to
46 Nm.
125.Remove plugs from tranmission and oil cooler
pipe.
126.Clean pipe, lubricate NEW 'O' ring and fit to
pipe.
127.Connect pipe to transmission and secure with
union. Tighten to
30 Nm.
128.Align pipe bracket to sump, position spacer and
fit bolt. Tighten to
18 Nm.
129.Fit heatshield and secure with nut.
130.Secure transducer lead to clip on heatshield.131.Slacken bell housing access plate bolt.
132.Move plate aside.
133.Remove block.
134.Align drive plate and torque converter.
135.Fit 2 torque converter bolts.
136.Rotate engine and fit second 2 bolts. Tighten to
45 Nm.
137.Rotate engine and tighten first 2 bolts to Tighten
to
45 Nm.
138.Clean cover plate and mating face.
139.Position cover plate and fit bolts. Tighten to
45
Nm.
140.Position access plate.
141.Fit 2 remaining bolts and tighten all bolts to
Tighten to
9 Nm.
142.Position engine harness around engine.
143.Connect knock sensor multiplug.
144.Connect starter solenoid Lucar.
145.Position starter motor heatshield and secure clip
to solenoid.
146.Align shield bracket to engine mounting bracket
and fit bolt. Tighten to
9 Nm.
147.Clean crankshaft sensor mating faces.
148.Position sensor and connect multiplug.
149.Position/align sensor and shield to backplate. Fit
bolts. Tighten to
6 Nm.
150.Fit tie bar, align to transmission and fit bolts.
Tighten to
25 Nm.
151.Fit tie bar securing nut. Tighten to45 Nm.
152.Fit catalytic converter/front pipe assembly.See
EMISSION CONTROL, Repair, Catalytic
Converter/Front Pipe - 4.0 V8
153.Raise engine.
154.Fit RH mounting rubber.
155.Move engine over.
156.Fit LH mounting rubber.
157.Lower engine.
158.Disconnect hoist.
159.Fit engine mounting nuts. Tighten to
55 Nm.
160.Remove plugs from steering pump and steering
box.
161.Clean PAS hose unions.
162.Lubricate 'O' rings and fit to hose unions.
163.Position hose.
164.Align unions to pump and steering box. Tighten
14mm thread to
15 Nm, 16mm thread to
Tighten to
20 Nm.
165.Remove plugs from feed hose and PAS pump.
166.Connect hose to pump and tighten clip.
167.Untie compressor and position to engine
bracket.
168.Position heatshield and fit bolts. Tighten to
25
Nm.
169.Connect compressor multiplug.
170.Position drive belt.

4.0 V8
7
REPAIR 171.Route drive belt around pulleys.
172.Pivot tensioner downwards.
173.Align belt to tensioner and release tensioner.
174.Connect battery positive lead and tighten.
175.Secure terminal cover.
176.Align gearbox breather pipe, clip to engine lifting
eye and fit bolt. Tighten to
9 Nm.
177.Align and secure engine harness brackets to
inlet manifold and fit nuts. Tighten to
9 Nm.
178.Connect injector multiplugs.
179.Connect air intake temperature sensor multiplug.
180.Connect fuel temperature sensor multiplug.
181.Connect coolant temperature multiplug.
182.Connect temperature gauge connector.
183.Connect oil pressure switch Lucar.
184.Connect camshaft sensor multiplug and secure
to bracket.
185.Fit ignition coil bracket.
See FUEL SYSTEM
SFI, Repair, Ignition Coils
186.Position heater hose/pipe assembly.
187.Connect hose to inlet manifold.
188.Align pipe to bracket and fit bolt. Tighten to
9
Nm.
189.Tighten hose clip.
190.Connect heater return hose and tighten clip.
191.Remove plugs from fuel feed and return hose
connections.
192.Clean feed unions.
193.Connect return hose and tighten clip.
194.Connect feed hose union and tighten.
195.Remove cloth.
196.Connect purge hose.
197.Connect leads to generator, tighten terminal nuts
and fit cover.
198.Connect sensing Lucar.
199.Connect servo vacuum hose.
200.Position expansion tank and secure with fixings.
201.Connect hose and tighten clip.
202.Lower ramp.
203.Fit mass air flow sensor.
See FUEL SYSTEM
SFI, Repair, Mass Air Flow Sensor (MAF
Sensor)
204.Fit plenum chamber.See FUEL SYSTEM SFI,
Repair, Plenum Chamber
205.Fit radiator.See COOLING SYSTEM, Repair,
Radiator
206.Fit bonnet.See CHASSIS AND BODY, Repair,
Bonnet [Hood]
207.Reconnect battery negative lead.
208.Bleed power steering system.
See STEERING,
Repair, Power Steering System - Bleed
209.Drain engine oil and refill.See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended Lubricants and Fluids - USA
Vehicles
210.Start engine. Check for fuel, coolant and oil
leaks.FRONT COVER GASKET
Service repair no - 12.65.04 - Front Cover Gasket
Remove
1.Disconnect battery negative lead.
2.Drain cooling system.
See COOLING SYSTEM
V8, Adjustment, Coolant
3.Remove radiatorSee COOLING SYSTEM,
Repair, Radiator
4.Remove water pump pulley.See COOLING
SYSTEM, Repair, Viscous Coupling, Fan
Blades, Pulley and Fan Cowl
5.Slacken bottom hose clip. Remove hose from
water pump.
6.Raise vehicle on ramp.
7.Disconnect oil cooler hoses from front cover and
position aside. Plug hoses and connections.
8.Disconnect Lucar from oil pressure switch.

Mpi
1
DESCRIPTION AND OPERATION DESCRIPTION
The 'T' Series engine is a four cylinder, water cooled
unit comprising a cast iron cylinder block, aluminium
alloy cylinder head and twin aluminium alloy camshaft
carriers.
The cylinder block incorporates direct bored,
siamesed cylinder bores which provide good structural
rigidity. The crankshaft is carried in five main
bearings, end-float being controlled by thrust washers
positioned each side of the centre main bearing.The main bearing caps are located to the cylinder
block by dowels; the bearing shells fitted to Nos. 1, 3
and 5 bearings are fully grooved whilst those fitted to
Nos. 2 and 4 bearings are plain.
The cylinder head carries twin camshafts operating
four valves per cylinder via hydraulic tappets. Both
camshafts are driven by the timing belt and run
directly in journals line bored in the cylinder head and
camshaft carriers. The plastic camshaft covers are
bolted to the camshaft carriers.