1995 LAND ROVER DISCOVERY oil

FRONT AXLE AND FINAL DRIVE
1
SERVICE TOOLS FRONT HUB
LRT-54-001 Oil seal replacer non ABS
LST550-5
LRT-99-003 Drift
18G134
LRT-54-002 Hub nut wrench
RO606435A
LRT-54-003 Hub oil seal replacer ABS
LST137

57STEERING
6
DESCRIPTION AND OPERATION Demand for assistance (Valve misaligned)
When the steering wheel and input shaft is turned,
steering resistance transmitted to the worm causes
the torsion bar to be twisted and the valve ports to be
misaligned for a right or left turn. The misalignment of
the valve ports directs all fluid pressure A to one side
of the piston only and allows displaced fluid B on the
other side.When demanding maximum assistance, any
excessive fluid output from the pump due to high
pump speed, will circulate through the regulator valve
located in the pump unit, causing the temperature of
the fluid and the pump to rise rapidly.
To avoid excessive fluid temperatures which could
damage the oil seals, the steering must not be held on
full lock for more that 30 seconds in one minute.
Only when the steering wheel and the demand for
assistance is released, will the torsion bar return the
valve to neutral, allowing the fluid to circulate through
the reservoir where it is cooled.
In the unlikely event of mechanical failure of the
torsion bar, a coarse splined connection (7) between
the input shaft and worm, ensures steering control is
maintained sufficient to allow the vehicle to be
recovered.
Rotary valve misaligned

57STEERING
4
FAULT DIAGNOSIS Symptom:-
Fluid leaks from steering box seals.
CAUTION: The steering wheel must not be
held on full lock for more than 30 seconds
in one minute, as this may overheat the
fluid and cause damage to the oil seals.
1.Check fluid level.
See Repair, Power Steering
Fluid Reservoir
Check fluid pressure.See Power Steering
System - Test
2.Is pressure high?
YES - Renew pump.
See Repair, Power
steering Pump
If oil seal leaks persist after renewing the
pump.
See Overhaul, Power Steering
Box
NO -See Overhaul, Power Steering Box
Symptom:-
Insufficient power assistance - castor return
action normal.
1.Are tyres correct type and pressure?
NO -
See GENERAL SPECIFICATION DATA,
Information, Wheels and Tyres
YES - Continue.
2.Is fluid level correct?
NO - Check fluid level
See Repair, Power
Steering Fluid Reservoir
YES - Check system for air locks.See Repair,
Power Steering System - Bleed
3.Is pressure correct?
NO - Check fluid pressure.
See Power
Steering System - Test
If pressure is not correct after bleeding
the system, renew pump.
See Repair,
Power Steering Pump
YES -See Overhaul, Power Steering Box
Symptom:-
Steering heavy - stiff, poor castor return action.
1.Are tyres correct type and pressure?
NO -
See GENERAL SPECIFICATION DATA,
Information, Wheels and Tyres
YES - Check universal joints for seizure and
correct alignment.
See Repair, Lower
Steering Shaft and Universal Joints
Check power steering box adjustments.
See Overhaul, Power Steering Box
2.Is the power assistance satisfactory?
NO - See fault symptomInsufficient
assistance, (castor return action
normal).
YES - Disconnect drag link from drop arm and
check steering column and box for
stiffness.
See Repair, Drag Link and
Drag Link Ends
3.Is the steering stiff with the drag link
disconnected?
NO - Check steering ball joints for seizure and
axle swivels lubrication and resistance.
See Repair, Drag Link and Drag Link
Ends See FRONT AXLE AND FINAL
DRIVE, Overhaul, Front Stub Axle,
Constant Velocity Joint and Swivel Pin
Housing Non ABS See FRONT AXLE
AND FINAL DRIVE, Overhaul, Front
Stub Axle, Constant Velocity Joint and
Swivel Pin Housing ABS
YES - Disconnect the lower steering shaft and
check the column and box for stiffness.
See Repair, Lower Steering Shaft and
Universal Joints
4.Is the steering column stiff to turn when
disconnected from the box?
NO - Remove and overhaul box.
See
Overhaul, Power Steering Box
YES - Adjust steering column.See Stiff
Steering Checklist

STEERING
5
FAULT DIAGNOSIS Symptom :-
Steering excessively light/sensitive. Excessive
freeplay at steering wheel.
1.Are steering box adjustments correct?
NO -
See Adjustment, Power Steering Box
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is within warranty, it must be
returned to manufacturer. No attempt must be
made to introduce backlash.
YES - Suspect worn panhard rod or radius arm
bushes Check condition of ball joints and
the lower steering column shaft universal
joints for wear.
See Repair, Lower
Steering Shaft and Universal Joints
Symptom :-
Steering vibration, road wheel shimmy - wobble.
Vibration through the steering linkage powerful
enough to induce high frequency oscillation of the
steering wheel, is generally caused by out of balance
road wheels. However there are a number of other
possible causes of this symptom which if severe, may
be described as shimmy or wobble. Regardless of the
terminology used by the owner/driver to describe the
symptoms, the following diagnostic checks should be
carried out in the order presented.
1.Check the tyres and balance of the road wheels.
See GENERAL SPECIFICATION DATA,
Information, Wheels and Tyres See
WHEELS AND TYRES, Fault diagnosis, Fault
- Symptoms See WHEELS AND TYRES,
Repair, Wheel Balancing
2.Check the steering hydraulic damper function.
See Steering Damper
3.Check steering column universal joints for wear
and correct alignment.
See Repair, Lower
Steering Shaft and Universal Joints
4.Check steering linkage ball joints for wear,
correct alignment and security, including steering
box and tie rod.
See Steering Linkage Inspect
5.Check all front suspension rubbers for wear.
Check all fixing torques, including radius arm
bushes, panhard rod and anti-roll [sway] bar.
See FRONT SUSPENSION, Repair, Panhard
Rod See FRONT SUSPENSION, Repair,
Radius Arm See FRONT SUSPENSION,
Repair, Anti-Roll[Sway] Bar Assembly See
FRONT SUSPENSION, Repair, Front Shock
Absorber
6.Fit new radius arm bushes using NTC 6860. Fit
harmonic damper if vehicle has air suspension.
Fit new nuts, bolts and washers.
7. Coil spring vehicles only- If problem persists
fit damper kit STC 241 (2 off front) and STC
1474 (2 off rear). Road test vehicle.
8.Check the power steering box adjustments and
operation.
See Overhaul, Power Steering Box
9.Check the hub bearing end floats and determine
the condition of the hub bearings. As applicable.
See FRONT AXLE AND FINAL DRIVE, Repair,
Front Hub Assembly
10.Check the resistance and condition of the
swivels.
See FRONT AXLE AND FINAL
DRIVE, Description and operation,
Description
If problem is not diagnosed: Repeat
checks starting at 1.
11.Carry out a full steering geometry check.
See
INTRODUCTION, Information, Steering

57STEERING
8
FAULT DIAGNOSIS 4. DIRECTIONAL STABILITY
From 1. GENERAL STEERING:
1.Is directional stability concern when vehicle is
towing?
YES - Check towing/vehicle loading parameters
in Owner's Handbook.
NO - go to 3.
2.Is problem resolved?
YES - end
NO - continue.
3.Check condition of rear trailing link/chassis
bushes.
4.Is problem resolved?
YES - end
NO - continue.
5.Check condition of front and rear shock
absorbers. If in doubt change units in pairs, side
to side.
6.Is problem resolved?
YES - end
NO - continue.
7.Check steering damper.
See Steering Damper
8.Is problem resolved?
YES - end
NO - continue.
9.Check wheel balance
10.Is problem resolved?
YES - end
NO - contact local technical office.POWER STEERING FLUID LEAKS
1.Is fluid level correct?
YES - go to 3.
NO - Refill or drain to correct level. Bleed
system, check for leaks.
See Repair,
Power Steering System - Bleed
2.Is problem resolved?
YES - end
NO - continue.
3.Are hoses or joints leaking? Check on full lock
with engine at 2000 rev/min.
YES - loosen and retorque joints.
NO - go to 6.
4.Does leak remain?
YES - change PAS pipe.
NO - end.
5.Does leak remain?
YES - suspect seal in component. Check and
replace as necessary.
NO - end.
6.Is oil escaping from filler cap?
YES - bleed system.
See Repair, Power
Steering System - Bleed
NO - go to 8.
7.Is oil still escaping from filler cap?
YES - go back to 1.
NO - end.
8.Is oil leaking from PAS pump?
YES - go to 10.
NO - continue.
9.Is oil leaking from PAS box?
YES - go to 10.
NO - end.
10.Clean unit, add tracer dye to system. Retest
11.Is oil still leaking?
YES - establish leak point. Repair or replace
unit as necessary.
NO - end.

57STEERING
12
FAULT DIAGNOSIS Steering column alignment
1.Place vehicle on level ground. Measure the
angle of lower steering shaft using a Pernumeter
placed on the shaft between the universal joints.
The angle should measure a minimum of 12Ê.
2.If necessary, realign the shaft. Release the five
fixings securing the steering column. Position
column as required. Tighten the fixings evenly,
27 Nm.
3.Loosen the three screws securing lower steering
column shroud to upper shroud ensure lower
shroud is clipped to upper shroud. Reposition
shroud, tighten screws.
4.Recheck steering column angle.
Steering box adjustment
1.Check steering box adjustment.
See
Adjustment, Power Steering Box
Steering damper check
1.Check condition of steering damper
See
Steering Damper
VISUAL CHECK AND BASIC ADJUSTMENTS
NOTE: It is important that the following
instructions are carried out in the
sequence shown and the results recorded.
1.Road springs - check that road springs are
correctly seated and are to correct specification
for vehicle. For spring specification.
See
GENERAL SPECIFICATION DATA,
Information, Road Springs Data
2.Ride height - measure trim height from wheel
centre to wheelarch eyebrow. Record results on
data sheet.
3.Check/top up power steering fluid
See Repair,
Power Steering Fluid Reservoir
4.Check tension and condition of drive belt.See
ENGINE, Repair, Drive Belt
5.Track rod/drag link - check condition of track rod,
drag link and ball joints.
See Repair, Drag Link
and Drag Link Ends
If either component is damaged, check operation
of steering damper and steering box for
smoothness. Replace all damaged or worn
components that impair the operation of the
steering system.
6.Suspension bushes - examine all steering and
suspension bushes for signs of wear and
deterioration. Also check all fixings for torque
relaxation. Tighten to correct torque value.
See
FRONT SUSPENSION, Specifications, torque,
Torque Values
7.Oil leaks - check front and rear axle hubs for
leak and repair as necessary.
8.Brake system - check brake system for leaks,
pipe condition, pad wear/contamination, disc
wear/condition and ABS sensors for correct
fitting.
9.Hub end float - check movement in the hubs by
rocking the wheels.
10.Check front wheel alignment. Vehicles displaying
a tendency to veer more than considered
allowable, it is permissible to set the front track
to parallel.
11.Having completed all the above checks and
adjustments, road test vehicle.
See Road Test
Procedure
Attempting to reproduce the symptoms
established earlier. If symptoms still exist refer to
relevant Diagnostic Chart.

57STEERING
4
REPAIR
Refit
15.Position steering box to chassis side member,
ensuring locating peg is engaged. Tighten bolts
to
81 Nm.
16.Fit pinch bolt and nut securing universal joint to
power steering box. Tighten to
25 Nm.
17.Position tie bar, tighten bolts and nut to81 Nm,
starting with tie bar to mounting nut, then
loosen nut and bolts by one complete turn.
18.Check steering box, adjust if necessary.See
Adjustment, Power Steering Box
19.Refit drag link to drop arm tighten nut to40 Nm.
20.Fit undertray.
21.Lower vehicle to ground.
22.Remove plugs and refit pipes to steering box.
Tighten 16mm thread to
20 Nm.
14mm thread to15 Nm.
23.Remove filler cap. Fill reservoir to oil level mark
on dipstick. Use recommended fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids
and bleed power steering system.See
Power Steering System - Bleed
24.Recheck fluid level and replace cap.
25.With engine running, test steering system for
leaks by holding steering in both full lock
directions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute, to avoid oil overheating and
possible seal damage.
26.Test drive vehicle: using both full lock directions,
to settle steering components. If possible, drive
vehicle over speed bumps and include harsh
braking.
WARNING: Do not test drive vehicle on
public highway.
27.Drive vehicle in a straight line on level ground
and stop.
28.Tighten tie bar to mounting nut to
110 Nm.
29.Tighten bolts securing tie bar to81 Nm.
30.Ensure steering wheel is correctly aligned when
wheels are positioned straight ahead.
31.If necessary reposition steering wheel.
See
Steering Wheel
32.Road test vehicle.

STEERING
1
OVERHAUL POWER STEERING BOX
Service repair no - 57.10.07
Overhaul
NOTE: Overhaul of steering box should
not be carried out during the warranty
period.
WARNING: Wear safety glasses while
removing and refitting circlips and
retaining ring.
CAUTION: Absolute cleanliness is
essential when overhauling power steering
box.
1.Remove steering box from vehicle.See Repair,
Power Steering Box
Remove drop arm using extractor LRT-57-012.
Loosen drop arm securing nut, but do not
remove before using extractor. Remove dirt
excluder from output shaft.
2.Drain oil, remove blanking plugs and bleed
screw. Hold steering box over suitable container,
turn input shaft from lock to lock, until oil is
drained. Refit bleed screw.
3.Rotate retainer ring until one end is 12 mm from
extractor hole. Using a drift through hole in
cylinder, lift retaining ring from groove in cylinder
bore.
4.Remove retainer ring, using a screwdriver.
5.Turn input shaft (left lock on left hand drive, right
lock on right hand drive) until piston pushes out
cover. Turn input shaft fully in opposite direction,
applying pressure to piston.
6.Remove set screw retaining rack pad adjuster.
7.Remove rack adjuster and pad.
8.Remove sector shaft adjuster locknut.
9.Remove four bolts from sector shaft cover.
10.Screw in sector shaft adjuster until cover is
removed.
NOTE: Sealant is applied to hexagon
socket to 'tamperproof' sector shaft
adjuster
11.Slide out sector shaft.