1995 LAND ROVER DISCOVERY oil

ZF
15
REPAIR GOVERNOR ASSEMBLY
Service repair no - 44.22.01
Remove
1.Remove transfer gearbox.
See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
2.Drain oil from automatic gearbox.
3.Remove bolts securing left hand mounting
bracket to extension housing and withdraw
bracket.
4.Remove transfer gear lever housing securing
bolts and move housing aside.
5.Remove extension housing ensuring seal is not
damaged, remove and discard gasket.
6.Remove extension shaft retaining bolt, withdraw
shaft and discard 'O' ring seal. If Tdi vehicle
remove spacer.
7.Remove governor assembly.
8.Remove park gear from governor assembly.
9.Detach governor housing.
10.Remove security clip and counter weight.
11.Remove and discard 'O' ring seal from output
shaft and three seal rings from 'F' clutch
housing.
12.Clean all components.
13.If necessary detach parking pawl by removing
guide plates and withdrawing mechanism.Refit
14.Refit parking pawl mechanism if removed.
15.Fit and lubricate new seal rings to 'F' clutch
housing shaft, ensure they are correctly seated.
16.Apply petroleum jelly to a new 'O' ring seal. Fit to
output shaft
17.Fit park gear to governor assembly tightening
screws to correct torque.
18.Fit governor assembly to output shaft.
19.Fit extension shaft with spacer if Tdi. Fit new 'O'
ring under bolt head.
20.Fit extension housing, avoid damaging seal.
Tighten to
23 Nm.
21.Refit transfer gear lever housing to extension
housing.
22.Refit mounting bracket to extension housing.
Tighten to
52 Nm.
23.Refit transfer gearbox.See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
24.Refill automatic gearbox with correct grade of oil.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids

44AUTOMATIC GEARBOX
18
REPAIR REPLACING TORQUE CONVERTER
1.Remove gearbox and transfer box assembly.
See LT230T Transfer Gearbox
2.Place gearbox on bench. Remove torque
converter using torque converter handles
18G1501, taking care not to damage torque
converter/oil pump housing oil seal.
3.Fit new torque converter using torque converter
handles 18G1501. Check dimension from
converter fixing boss to converter housing face is
50 mm. This shows converter is correctly seated
in housing.
4.Refit gearbox and transfer box assembly.
See
LT230T Transfer Gearbox
ELIMINATING LEAKS ON PUMP HOUSING
1.Remove gearbox and transfer box assembly.
See LT230T Transfer Gearbox
2.Place gearbox on bench. Remove torque
converter using torque converter handles
18G1501, taking care not to damage torque
converter/oil pump housing oil seal.
3.Remove twelve hexagonal bolts (inner ring
pattern).
4.Remove bell housing and pump assembly,
discard gasket.
5.Remove eight hexagonal bolts on rear of pump.

ZF
19
REPAIR 6.Screw in two bolts, diagonally opposite each
other. Tap lightly using a soft headed mallet to
remove pump assembly from intermediate plate.
7.Remove shaft sealing ring and 'O' ring from
pump housing and discard.
8.Using oil seal replacer LST108 fit shaft seal ring
into pump housing.
9.Fit 'O' ring onto circumference of pump housing.
10.Align dowel with hole in intermediate plate and
press pump housing home.11.Fit pump housing to intermediate plate, tighten
eight bolts to
10 Nm.
12.Place bell housing and intermediate plate
assembly on bench, front face up. Using oil
pump rotation sleeve LST111, check that pump
gears rotate freely.
13.Before fitting intermediate plate and bell housing
assembly,check that thrust washer and axial
cage are seated on A clutch housing.
14.Place gasket and disc washer onto bell housing
and intermediate plate assembly using
Petroleum Jelly.
15.Fit bell housing and intermediate plate assembly
to gearcase. Tighten twelve bolts to
46 Nm.
16.Place end float gauge LST111 onto pump
housing and check that axial play is between
0.2-0.4 mm. Replace existing washer, situated at
rear of intermediate plate, with a suitable washer
to give required end float.
17.Refit torque converter into housing using torque
converter handles 18G1501, checking that
dimension from converter fixing bolt boss to
converter housing face is 50 mm. This shows
converter is properly seated in housing.
18.Refit gearbox/transfer box assembly.
See
LT230T Transfer Gearbox

44AUTOMATIC GEARBOX
20
REPAIR ELIMINATING LEAKS BETWEEN GEARBOX
HOUSING AND INTERMEDIATE PLATE
1.Remove gearbox and transfer box assembly.
See LT230T Transfer Gearbox
2.Place gearbox on bench. Remove torque
converter using torque converter handles
18G1501, taking care not to damage torque
converter/oil pump housing oil seal.
3.Remove twelve hexagonal bolts (inner ring
pattern).
4.Remove bell housing/intermediate plate
assembly from gearbox case and discard
gasket.
5.Place new gasket onto intermediate plate using
Petroleum Jelly.
6.Before fitting bell housing assembly check that
thrust washer and axial cage are seated on A
clutch housing.
7.Fit bell housing assembly with disc washer to
gearcase. Tighten twelve bolts to
46Nm.
8.Place end-float gauge LST111 onto pump
housing and check that axial play is between
0.2-0.4 mm. Replace existing washer, situated at
rear of intermediate plate, with a suitable washer
to give required end-float.
9.Refit torque converter using torque converter
handles 18G1501. Checking that dimension
from converter fixing boss to converter housing
case is 50mm. This dimension shows converter
is properly seated.
10.Refit gearbox/transfer box assembly.
See
LT230T Transfer Gearbox

ZF
21
REPAIR REPLACING PUMP
Service repair no - 44.32.01
1.Remove gearbox and transfer box assembly.
See LT230T Transfer Gearbox
2.Place gearbox on bench. Remove torque
converter using torque converter handles
18G1501, taking care not to damage torque
converter/oil pump housing oil seal.
3.Remove twelve bolts (inner ring pattern).
4.Remove bell housing and pump assembly from
gearbox case, discard gasket.
5.Remove eight bolts on rear of pump.
6.Screw in two bolts,diagonally opposite each
other, tap lightly using a soft headed mallet to
free pump assembly from intermediate plate.
7.Fit new pump assembly, aligning dowel with hole
in intermediate plate, press pump housing home.
8.Secure pump housing to intermediate plate
using eight hexagonal bolts. Tighten to
10 Nm.
9.Place bell housing and intermediate plate
assembly on bench, front face up. Using oil
pump rotation sleeve LST111, check that pump
gears rotate freely.
10.Before replacing intermediate plate/bell housing
assembly check that thrust washer and axial
cage are seated on A clutch housing.
11.Place new gasket and disc washer onto bell
housing and intermediate plate assembly using
a Petroleum Jelly.
12.Fit bell housing and intermediate plate assembly,
tighten twelve bolts to
46 Nm.

ZF
3
SERVICE TOOLS AUTOMATIC GEARBOX
LRT-44-001 Front and rear oil seal replacer.
LST 108
LRT-44-002 Selector linkage setting gauge.
LST 109
LRT-44-003 Oil pump rotation sleeve and end float
LST 111 gauge.
LRT-44-004 Kickdown cable remover.
LST 112

44AUTOMATIC GEARBOX
4
SERVICE TOOLS
LRT-44-005 Control unit oil seal remover/replacer.
LST 113
LRT-44-006 Selector shaft oil seal replacer.
LST 114
LRT-44-007 Line pressure test gauge.
18G.502A
LRT-44-008 Hose and adaptor.
18G.502K

PROPELLER SHAFTS
1
FAULT DIAGNOSIS VIBRATION HARSHNESS
1.Check that the propeller shaft universal joints
and sliding splines are not siezed or worn and
that the shafts are correctly aligned.
NOTE: In the event that both shafts are
satisfactory, but the vibration/harshness is
still present, the transfer box operation
and balance of the road wheels should be
checked.
For transfer box operation.
See TRANSFER
GEARBOX, Fault diagnosis, LT230T Transfer Box
- Oil Leaks
For balance of road wheels.See WHEELS AND
TYRES, Repair, Wheel Balancing