1995 LAND ROVER DISCOVERY oil

26COOLING SYSTEM
2
REPAIR WATER PUMP
Service repair no - 26.50.01
Remove
WARNING: Disconnect battery negative
terminal to prevent engine being started
before removing drive belts.
1.Drain engine cooling system.
See Adjustment,
Coolant
2.Remove top hose radiator to thermostat.
3.Remove top hose intercooler to induction
manifold.
4.Slacken water pump and power steering pump
pully retaining bolts.
5.Remove drive belt.
6.Remove centre nut from belt tensioner.
7.Manoeuvre pulley upwards and withdraw
tensioner from retaining stud.
8.Disconnect hose thermostat to bottom hose,
release hose from clip on water pump and move
aside.
9.Remove water pump pulley.
10.Remove power steering pump pulley.
11.Remove 8 bolts securing water pump, noting
location of 3 through bolts.
12.Withdraw pump and gasket, clean all gasket
material from mating surfaces.
Refit
13.Refit water pump in reverse order to removal
using new gasket.RADIATOR
Service repair no - 26.40.01
Remove
1.Drain cooling system.
See Adjustment,
Coolant
2.Disconnect radiator top hose.
3.Remove fan blade assembly.
4.Remove cowl.
5.Disconnect engine oil cooler connections and
turbo intercooler connections from radiator ends.
NOTE: Oil spillage will occur when
connections are loosened. Blank off
exposed oil connections.
6.Disconnect expansion tank bleed hose from
radiator.
7.Remove radiator securing brackets from each
side.
8.Remove radiator unit by lifting from its location.
Check condition of rubber mounting pads.
Refit
9.Check radiator sealing strips are securely
located.
10.Transfer oil cooler adaptors if fitting new radiator.
11.Reverse removal procedure. Tighten oil cooler
connections to
30 Nmbefore fitting fan blades
and cowl.
12.Check all connections for leaks.

V8i
1
DESCRIPTION AND OPERATION ENGINE COOLING
Description
The V8i engine uses a pressurised cooling system
and cross flow radiator which is supplied from a
separate header tank. The coolant radiator also
incorporates a section at the left hand end for cooling
the transmission oil and a section at the other end for
cooling the engine oil.The belt driven viscous fan and centrifugal water
pump is located in the engine front cover with ports for
circulation of coolant to both banks of cylinders and
cylinder heads. Coolant returns to the top of the
radiator via ports in the inlet manifold where the
thermostat is mounted horizontally.
Coolant also circulates through the vehicle heating
system and is used to heat air entering the inlet
manifold plenum chamber.
Coolant circulation (engine hot)
1. Cross flow radiator
2. Header tank
3. Viscous fan and water pump
4. Heater pipes
5. Plenum chamber connection
6. Thermostat

V8i
1
FAULT DIAGNOSIS ENGINE OVERHEATING
Before conducting any cooling system diagnosis:
See
Description and operation, Engine Cooling
1.Is coolant level correct?
NO - Allow engine to cool, top up level to
expansion tank seam.
YES - Continue.
2.Is drive belt tension correct?
NO -
See ENGINE, Repair, Drive Belt -
Check Tension
YES - Continue.
3.Is ignition timing correct?
NO -
See ELECTRICAL, Adjustment,
Ignition Timing
YES - Continue.
4.Is coolant in radiator frozen?
YES - Slowly thaw and drain system.
See
Adjustment, Coolant Requirements
NO - Continue.
5.Is air flow through radiator restricted or blocked?
YES - Apply air pressure from engine side of
radiator to clear obstruction.
NO - Continue.
6.Are there any external leaks, from water pump,
engine gaskets or the heater unit?
YES - Investigate and rectify.
See Adjustment,
Coolant Requirements
NO - Continue.
7.Are fan blades fitted correct way round, concave
side towards engine?
NO - Rectify.
YES - Continue.8.Is viscous unit operating correctly?
See
Description and operation, Viscous Fan
NO - Renew.See Repair, Viscous
Coupling, Fan Blades, Pulley and Fan
Cowl
YES - Carry out a pressure test on radiator cap
and system. Check thermostat type,
operation and correct fitting
See Repair,
Thermostat
If pressure test leads you to suspect coolant
leakage across gaskets, go to check 11,
otherwise: Continue.
9.Are the air conditioning fans operating correctly?
See Electrical Trouble Shooting Manual.K5
NO - Rectify.
YES - Continue.
10.Is temperature sender and gauge giving
accurate readings?
NO - Substitute parts and compare readings.
YES - Continue.
11.Carry out cylinder pressure test to determine if
pressure is leaking into cooling system causing
over pressurising and loss of coolant.
If problem is not diagnosed, check the coolant system
for engine oil contamination and engine lubrication
system for coolant contamination.
If the coolant only, or both systems are contaminated,
suspect cylinder head gaskets or radiator.
If only the lubrication stystem is contaminated with
coolant, suspect inlet manifold or front cover gaskets.

26COOLING SYSTEM
4
REPAIR RADIATOR
Service repair no - 26.40.01
Remove
1.Drain cooling system.
See Adjustment,
Coolant
2.Remove viscous coupling and fan assembly.
See Viscous Coupling, Fan Blades, Pulley
and Fan Cowl
3.Release 2 clips and remove fan cowl.
4.Disconnect radiator top hoses.
5.Disconnect four transmission and engine oil
cooler connections to radiator end tanks. Note oil
spillage will occur when connections are
loosened. Blank off exposed oil connections.
6.Disconnect transmission oil temperature sensor.
7.Remove radiator securing brackets from each
side.
8.Remove radiator unit by lifting from its location.
Check condition of rubber mounting pads.Refit
9.Reverse removal procedure.
10.Clean unions and apply sealant.
11.Lubricate new 'O' rings before fitting.
12.Check radiator sealing strips are securely
located.
13.Transfer oil cooler adaptors if fitting new radiator.
14.Ensure that oil cooler connections are tightened
to
30 Nm.before fitting fan blades and cowl.
15.Clean coolant/oil spillage from vehicle.
16.Check all connections for coolant/oil leaks.

V8i
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Oil cooler pipes 30..........................................................................................
Radiator filler plug (plastic) 6.........................................................................

30MANIFOLD AND EXHAUST SYSTEM
4
REPAIR EXHAUST MANIFOLD - Tdi
Service repair no - 30.15.10
Remove
1.Disconnect battery negative lead.
2.Remove heat shield from rear of air intake
manifold.
3.Release dip stick tube from cylinder block.
4.Disconnect the intake hose from the manifold.
5.Remove the two bolts and two nuts securing the
intake manifold to the cylinder head and
withdraw the inlet manifold.
6.Remove air filter inlet pipe to turbo unit.
7.Remove intercooler pipe from turbo to
intercooler.
8.Disconnect the EGR pipe from the inlet manifold
hose.
9.Remove the three fixings at the exhaust pipe
flange.
10.Release the turbo charger oil pipes from the
cylinder block.
11.Remove the turbo boost pipes.
12.Remove seven bolts securing the exhaust
manifold, release the heater rail and remove the
manifold gasket, complete with turbo unit.
13.Remove four bolts and disconnect diaphragm
rod from manifold, and remove turbo charger if
necessary.
Refit
14.Reverse removal procedure. 1 to 12. Use a new
manifold and exhaust flange gaskets.
15.Reconnect battery negative lead. Start engine
and check for leaks.

CLUTCH
1
FAULT DIAGNOSIS CLUTCH ASSEMBLY CONDITIONS
For the clutch to operate correctly as described and
illustrated in the "Description and Operation", it is
important the following conditions are satisfied:-
A. The primary shaft 15 must be free in the
crankshaft spigot bush 17.
B. The friction plate 2 must be able to slide easily
on the splines on the primary shaft 15, to a
position where it does not contact either the
flywheel or the pressure plate.
C. The friction plate must not be distorted or the
linings contaminated with oil, which may cause it
to stick or continue to run in contact with the
flywheel or pressure plate.
A number of faults can develop in the operation of the
clutch for a variety of reasons and although most
faults are due to normal wear at high mileage,
problems can also occur if the unit has been renewed
by an unskilled operator.
Recognising and diagnosing a particular clutch fault is
therefore of paramount importance in ensuring, that
the problem is rectified at the first attempt.
Problems which develop in the clutch are as follows:-
A. Clutch spin/drag
B. Clutch slip
C. Clutch judder/fierceCLUTCH SPIN - DRAG
Symptoms
Clutch spin is that, with engine running and clutch
pedal depressed, the gears cannot be immediately
engaged without making a grinding noise. This
indicates the clutch is not making a clean break.
However, if the clutch pedal is held depressed for
several seconds the friction plate will eventually break
free from the engine and the gear will engage silently.
Clutch spin as it becomes more severe develops into
clutch drag, making the silent engagement of a gear
impossible, regardless of how long the pedal is held
depressed.
CLUTCH SLIP
Symptoms
Clutch slip is most evident climbing a hill or when the
vehicle is moving off from stationary with a heavy
load. As the clutch is released slip occurs between the
engine and the transmission, allowing the engine
speed to increase without a corresponding increase in
vehicle speed.
Clutch slip can develop to the stage where no power
is transmitted through the clutch as the pedal is
released.
CLUTCH JUDDER - FIERCE
Symptoms
Clutch judder or fierce engagement, like slip, is most
likely to occur when the vehicle is moving off from
stationary. As the clutch pedal is released the vehicle
will move rapidly or in a series of jerks, which can not
be controlled even by careful operation of the clutch
by the driver.
It should be noted that a vehicle may display all the
symptoms or any combination of the symptoms
described, depending on the driving conditions vehicle
load and operating temperatures.

33CLUTCH
2
FAULT DIAGNOSIS FAULT/SYMPTOM CHART
Symptoms
Slip Spin/Drag Judder/Fierce Fault Item
* * * Worn or oil on clutch linings 2
* * * Mechanical damage45678
* * Distorted clutch plate 2
* Failed or air in hydraulic system 12 13
* * Primary shaft tight fit in crankshaft bush 15 17
* Clutch splines sticking 2 15
* Weak clutch plate springs or insecure/worn
engine/gearbox mountings6
* Insecure/worn propeller shafts
* Insecure/worn suspension components/rubber
bushes
For items refered to in this chart.See Description and operation, Description
CLUTCH NOISE - MECHANICAL FAULTS
Noise from clutch or gearbox in neutral, which
disappears when clutch is depressed.
Suspect gearbox input/primary shaft bearings.
See MANUAL GEARBOX, Fault diagnosis,
Manual Gearbox
- Noise from gearbox in neutral, which
disappears when clutch is depressed
Noise from clutch or gearbox in neutral, which
changes tone or becomes worse when the clutch
is depressed.
Suspect worn release bearing.
Knocking/rattling from clutch or gearbox in
neutral, which is reduced or disappears when the
clutch is depressed.
Suspect worn/weak release lever retainer or
clutch unit.
Noise from clutch or gearbox in neutral, which
disappears when clutch is depressed.
Suspect gearbox fault.
See MANUAL GEARBOX, Fault diagnosis,
Manual Gearbox
- Noise from gearbox in neutral, which
disappears when clutch is depressed.HYDRAULIC FAULTS
Unable to dis-engage clutch, little or no pedal
resistance.
1.Check condition, specification and level of fluid.
2.Check pipes and cylinders for leaks.
3.Check that air vent in reservoir lid is clear.
Suspect faulty master cylinder if no fluid leaks
present.
See Repair, Master Cylinder
Spongy pedal operation
1.Check condition, specification and level of fluid.
2.Check that air vent in reservoir lid is clear.
Suspect air in fluid.
See Repair, Bleed Hydraulic System
Clutch is difficult to dis-engage and/or does not
immediately re-engage when pedal is released.
1.Check condition, specification and level of fluid.
2.Check that air vent in reservoir lid is clear.
Suspect pedal pivot, master cylinder or slave
cylinder seizure.
See Repair, Master Cylinder