1995 LAND ROVER DISCOVERY lock

STEERING
3
DESCRIPTION AND OPERATION Steering column components
1. Upper shroud
2. Column harness
3. Cruise control switch (if fitted)
4. Steering wheel and nut
5. Rotary coupler
6. Column switch
7. Shear bolts
8. Switch saddle
9. Upper steering column
10. Universal joint
11. Universal joint bolt
12. Steering column lock assembly13. Lower shroud
14. Column lock/ignition
15. Air bag mounting bracket (if fitted)
16. Air bag module
17. Steering pad (non-airbag)
18. Lower shaft
19. Rubber coupling
20. Compression joint
21. Universal joint
22. Universal joint bolt

57STEERING
4
DESCRIPTION AND OPERATION
Power steering box components
1. Housing complete with sector shaft bearings
2. Cover plate complete with bearing
3. Sector shaft
4. Hydraulic piston/rack
5. Worm/valve and torsion bar assembly
6. Shims for centralizing worm/valve
7. Ball race (2)
8. 'Teflon' seals for valve sleeve (3)
9. Bearing adjuster, locknut and seal
10. Worm shaft pressure seal, circlip and dirt
excluder11. 'Teflon' and rubber seal for piston
12. End cover seal and snap ring
13. Adjustment components for piston/rack
14. Hydraulic pipe
15. Bleed screw
16. Sector shaft adjustment lock nut with seal
17. Cover plate bolts (4)
18. Cover plate seal
19. Seal, washer and backup seal
20. Circlip and dust cover

57STEERING
6
DESCRIPTION AND OPERATION Demand for assistance (Valve misaligned)
When the steering wheel and input shaft is turned,
steering resistance transmitted to the worm causes
the torsion bar to be twisted and the valve ports to be
misaligned for a right or left turn. The misalignment of
the valve ports directs all fluid pressure A to one side
of the piston only and allows displaced fluid B on the
other side.When demanding maximum assistance, any
excessive fluid output from the pump due to high
pump speed, will circulate through the regulator valve
located in the pump unit, causing the temperature of
the fluid and the pump to rise rapidly.
To avoid excessive fluid temperatures which could
damage the oil seals, the steering must not be held on
full lock for more that 30 seconds in one minute.
Only when the steering wheel and the demand for
assistance is released, will the torsion bar return the
valve to neutral, allowing the fluid to circulate through
the reservoir where it is cooled.
In the unlikely event of mechanical failure of the
torsion bar, a coarse splined connection (7) between
the input shaft and worm, ensures steering control is
maintained sufficient to allow the vehicle to be
recovered.
Rotary valve misaligned

STEERING
1
FAULT DIAGNOSIS INSUFFICIENT POWER ASSISTANCE
1.Is fluid level correct?
YES - go to 3.
NO - Fill/bleed sytem
2.Is problem a leak?
YES - Diagnose.
See Power Steering Fluid
Leaks
NO - continue
3.Is drive belt tension correct?
YES - go to 5.
NO - retension.
See ENGINE, Repair, Drive
Belt
4.Is problem resolved?
YES - end
NO - continue
5.Carry out pressure test at idle and 1000 rev/min.
See Power Steering System - Test
6.Is correct pressure achieved?
YES - steering box defective
Not at any speed go to 9.
Not at idle go to 7.
7.Is idle speed correct?
YES- Goto8.
NO - Correct idle speed -
If 3.9
See ENGINE TUNING DATA,
Information, Engine 3.9 V8i
If TdiSee ENGINE TUNING DATA,
Information, 300 Tdi Engine
If MpiSee ENGINE TUNING DATA,
Information, Engine - Mpi - 2.0 Litre
8.Is problem resolved?
YES - end
NO - go to 9.
9.Bypass steering box using adaptor tap
LRT-57-001
10.Is correct pressure obtained?
YES - defective steering box
NO - defective steering pump
CAUTION: Do not hold steering wheel on
full lock for more than 30 seconds in any
one minute to avoid overheating fluid and
possibly damaging seals.
NOTE: 1. Excessive pressure in the
system is almost always caused by a
faulty relief valve in the PAS pump.
NOTE: 2. Insufficient pressure in the
system is usually caused by low fluid level
or PAS pump drive belt slip, or one of the
following: PAS system leaks, faulty PAS pump
relief valve, fault in steering box valve and worm
assembly, leak at piston in steering box, worn
components in PAS pump or box.

57STEERING
2
FAULT DIAGNOSIS POWER STEERING SYSTEM - TEST
NOTE: If steering lacks power assistance.
Check pressure of hydraulic pump before
fitting new components. Use fault
diagnosis chart to assist in tracing faults.
A. Steering box.
B. Steering pump.
C. Existing hose, steering box to pump.
D. Hose LRT-57-030.
E. Test adaptor LRT-57-001.
F. Pressure gauge LRT-57-005.
G. Thread adaptor LRT-57-004.
H. Thread adaptor LRT-57-022.Procedure
1.A hydraulic pressure gauge and test adaptor is
used to test power steering system. This gauge
is able to measure 140 kgf/cm
2. The maximum
power steering system pressure is 77 kgf/cm2.
2.Some fault conditions of hydraulic pump may
obtain pressures up to 105 kgf/cm
2. Pressure on
gauge is same pressure being exerted upon
steering wheel. When testing, turn steering
wheel gradually while reading pressure gauge.
3.Check and maintain maximum fluid level of
reservoir.
4.Examine power steering units and connections
for leaks. All leaks must be rectified before
attempting to test the system.
5.Check steering pump drive belt tension.
See
ENGINE, Repair, Drive Belt
6.Assemble test equipment and fit to vehicle, as
shown in RR3959M.
7.Open tap of adaptor.
8.Bleed system, take care not to overload
pressure gauge.
9.With system in good condition, pressures should
be:
(A) Steering wheel held on full lock and engine
running at 1,000 rev/min, 70 to 77 kgf/cm
2.
(B) Steering wheel held on full lock and engine
idling, 28 kgf/cm
2.
Checks should be carried out on both full lock
positions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute to avoid overheating fluid and
possibly damaging seals.
10.Release steering wheel and with engine idling.
Pressure should read below 7 kgf/cm
2.
11.If pressures differ to those given a fault exists.
12.To determine if fault is steering box or pump.
Close adaptor tap for a maximum five seconds.
13.If gauge does not register specified pressure,
pump is faulty.
14.Fit a new pump, bleed system and repeat test. If
low pressure or a substantial imbalance exists,
fault is in steering box valve and worm
assembly.

57STEERING
4
FAULT DIAGNOSIS Symptom:-
Fluid leaks from steering box seals.
CAUTION: The steering wheel must not be
held on full lock for more than 30 seconds
in one minute, as this may overheat the
fluid and cause damage to the oil seals.
1.Check fluid level.
See Repair, Power Steering
Fluid Reservoir
Check fluid pressure.See Power Steering
System - Test
2.Is pressure high?
YES - Renew pump.
See Repair, Power
steering Pump
If oil seal leaks persist after renewing the
pump.
See Overhaul, Power Steering
Box
NO -See Overhaul, Power Steering Box
Symptom:-
Insufficient power assistance - castor return
action normal.
1.Are tyres correct type and pressure?
NO -
See GENERAL SPECIFICATION DATA,
Information, Wheels and Tyres
YES - Continue.
2.Is fluid level correct?
NO - Check fluid level
See Repair, Power
Steering Fluid Reservoir
YES - Check system for air locks.See Repair,
Power Steering System - Bleed
3.Is pressure correct?
NO - Check fluid pressure.
See Power
Steering System - Test
If pressure is not correct after bleeding
the system, renew pump.
See Repair,
Power Steering Pump
YES -See Overhaul, Power Steering Box
Symptom:-
Steering heavy - stiff, poor castor return action.
1.Are tyres correct type and pressure?
NO -
See GENERAL SPECIFICATION DATA,
Information, Wheels and Tyres
YES - Check universal joints for seizure and
correct alignment.
See Repair, Lower
Steering Shaft and Universal Joints
Check power steering box adjustments.
See Overhaul, Power Steering Box
2.Is the power assistance satisfactory?
NO - See fault symptomInsufficient
assistance, (castor return action
normal).
YES - Disconnect drag link from drop arm and
check steering column and box for
stiffness.
See Repair, Drag Link and
Drag Link Ends
3.Is the steering stiff with the drag link
disconnected?
NO - Check steering ball joints for seizure and
axle swivels lubrication and resistance.
See Repair, Drag Link and Drag Link
Ends See FRONT AXLE AND FINAL
DRIVE, Overhaul, Front Stub Axle,
Constant Velocity Joint and Swivel Pin
Housing Non ABS See FRONT AXLE
AND FINAL DRIVE, Overhaul, Front
Stub Axle, Constant Velocity Joint and
Swivel Pin Housing ABS
YES - Disconnect the lower steering shaft and
check the column and box for stiffness.
See Repair, Lower Steering Shaft and
Universal Joints
4.Is the steering column stiff to turn when
disconnected from the box?
NO - Remove and overhaul box.
See
Overhaul, Power Steering Box
YES - Adjust steering column.See Stiff
Steering Checklist

57STEERING
6
FAULT DIAGNOSIS STEERING STABILITY AND VEER UNDER
BRAKING
Possible cause:
Incorrectly set, swivel pin bearing preload. There are
three different settings for these bearings dependant
on model year and if fitted with ABS brakes.
Remedy.
1.Establish model year of vehicle.
2.If fitted with or without antilock brakes.
3.Follow instructions to overhaul front stub axle,
constant velocity joint and swivel pin non ABS,
or with ABS as appropriate.
See FRONT AXLE AND FINAL DRIVE,
Overhaul, Front Stub Axle, Constant Velocity
Joint and Swivel Pin Housing Non ABS See
FRONT AXLE AND FINAL DRIVE, Overhaul,
Front Stub Axle, Constant Velocity Joint and
Swivel Pin Housing ABS
1. GENERAL STEERING
1.Carry out visual and safety checks.
See Visual
and Safety Checks
2.Road test vehicle.See Road Test Procedure
3.Is problem resolved?
YES - end
NO - continue
4.Is problem stiff steering?
YES -
See Stiff Steering Checklist
NO- Goto6.
5.Is problem resolved?
YES - end
NO - go to 8.
6.Is problem steering niggle ?
YES - Replace radius arm bushes, arm and
axle.
See FRONT SUSPENSION,
Repair, Radius Arm
NO - go to 8.
7.Is problem resolved?
YES - end
NO - continue.
8.Centralise steering box.
See Adjustment,
Centralise Steering Box
9.Is problem resolved?
YES - end
NO - continue.
10.Check, adjust if necessary, steering geometry.
11.Is problem resolved?
YES - end
NO - continue.
12.Categorise the remaining problems into one or
more of the following descriptions:
See 2. Steering Veer
See 3. Veer Under Braking
See 4. Directional Stability

57STEERING
8
FAULT DIAGNOSIS 4. DIRECTIONAL STABILITY
From 1. GENERAL STEERING:
1.Is directional stability concern when vehicle is
towing?
YES - Check towing/vehicle loading parameters
in Owner's Handbook.
NO - go to 3.
2.Is problem resolved?
YES - end
NO - continue.
3.Check condition of rear trailing link/chassis
bushes.
4.Is problem resolved?
YES - end
NO - continue.
5.Check condition of front and rear shock
absorbers. If in doubt change units in pairs, side
to side.
6.Is problem resolved?
YES - end
NO - continue.
7.Check steering damper.
See Steering Damper
8.Is problem resolved?
YES - end
NO - continue.
9.Check wheel balance
10.Is problem resolved?
YES - end
NO - contact local technical office.POWER STEERING FLUID LEAKS
1.Is fluid level correct?
YES - go to 3.
NO - Refill or drain to correct level. Bleed
system, check for leaks.
See Repair,
Power Steering System - Bleed
2.Is problem resolved?
YES - end
NO - continue.
3.Are hoses or joints leaking? Check on full lock
with engine at 2000 rev/min.
YES - loosen and retorque joints.
NO - go to 6.
4.Does leak remain?
YES - change PAS pipe.
NO - end.
5.Does leak remain?
YES - suspect seal in component. Check and
replace as necessary.
NO - end.
6.Is oil escaping from filler cap?
YES - bleed system.
See Repair, Power
Steering System - Bleed
NO - go to 8.
7.Is oil still escaping from filler cap?
YES - go back to 1.
NO - end.
8.Is oil leaking from PAS pump?
YES - go to 10.
NO - continue.
9.Is oil leaking from PAS box?
YES - go to 10.
NO - end.
10.Clean unit, add tracer dye to system. Retest
11.Is oil still leaking?
YES - establish leak point. Repair or replace
unit as necessary.
NO - end.