1995 LAND ROVER DISCOVERY check engine

57STEERING
12
FAULT DIAGNOSIS Steering column alignment
1.Place vehicle on level ground. Measure the
angle of lower steering shaft using a Pernumeter
placed on the shaft between the universal joints.
The angle should measure a minimum of 12Ê.
2.If necessary, realign the shaft. Release the five
fixings securing the steering column. Position
column as required. Tighten the fixings evenly,
27 Nm.
3.Loosen the three screws securing lower steering
column shroud to upper shroud ensure lower
shroud is clipped to upper shroud. Reposition
shroud, tighten screws.
4.Recheck steering column angle.
Steering box adjustment
1.Check steering box adjustment.
See
Adjustment, Power Steering Box
Steering damper check
1.Check condition of steering damper
See
Steering Damper
VISUAL CHECK AND BASIC ADJUSTMENTS
NOTE: It is important that the following
instructions are carried out in the
sequence shown and the results recorded.
1.Road springs - check that road springs are
correctly seated and are to correct specification
for vehicle. For spring specification.
See
GENERAL SPECIFICATION DATA,
Information, Road Springs Data
2.Ride height - measure trim height from wheel
centre to wheelarch eyebrow. Record results on
data sheet.
3.Check/top up power steering fluid
See Repair,
Power Steering Fluid Reservoir
4.Check tension and condition of drive belt.See
ENGINE, Repair, Drive Belt
5.Track rod/drag link - check condition of track rod,
drag link and ball joints.
See Repair, Drag Link
and Drag Link Ends
If either component is damaged, check operation
of steering damper and steering box for
smoothness. Replace all damaged or worn
components that impair the operation of the
steering system.
6.Suspension bushes - examine all steering and
suspension bushes for signs of wear and
deterioration. Also check all fixings for torque
relaxation. Tighten to correct torque value.
See
FRONT SUSPENSION, Specifications, torque,
Torque Values
7.Oil leaks - check front and rear axle hubs for
leak and repair as necessary.
8.Brake system - check brake system for leaks,
pipe condition, pad wear/contamination, disc
wear/condition and ABS sensors for correct
fitting.
9.Hub end float - check movement in the hubs by
rocking the wheels.
10.Check front wheel alignment. Vehicles displaying
a tendency to veer more than considered
allowable, it is permissible to set the front track
to parallel.
11.Having completed all the above checks and
adjustments, road test vehicle.
See Road Test
Procedure
Attempting to reproduce the symptoms
established earlier. If symptoms still exist refer to
relevant Diagnostic Chart.

STEERING
1
ADJUSTMENT POWER STEERING BOX
Service repair no - 57.10.13
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is stiff or tight and within
warranty, it must be returned to manufacturer. No
attempt must be made to introduce backlash.
1.Apply park brake, select 'P' in automatic
transmission and chock wheels. Support chassis
front on axle stands.
2.Remove engine undertray.
3.Disconnect drag link from steering drop arm.
4.Check torque to turn.
See Fault diagnosis,
Stiff Steering Checklist
5.Centralise steering box.See Centralise
Steering Box
NOTE: Only check for no backlash when
steering box is in central position.
NOTE: If steering wheel is not straight, it
should be repositioned.
See Repair,
Steering Wheel
The adjustment of the steering box ensures
any preload or end float present on centre is
removed.
6.The adjustment is obtained by rocking the drop
arm about centre whilst an assistant slowly
tightens the steering box adjuster screw.
7.Tighten the locknut when all backlash has been
removed.
8.Repeat the check for backlash. If backlash exists
loosen locknut and repeat adjustment
procedure.
9.Turn steering wheel lock to lock and check no
tightness exists.
10.Ensure front wheels are aligned and in straight
ahead position.
See Front Wheel Alignment
11.Adjust drag link 924 mm between ball joint
centres.
12.Connect drag link. Tighten to
40 Nm.
13.Lower vehicle to ground level and remove
chocks.
14.Road test vehicle.
See Fault diagnosis, Road
Test Procedure
NOTE: If steering wheel is not in straight
ahead position when vehicle is travelling
in a straight line, drag link length is
incorrect and is pushing drop arm away from
central position.
Drag link adjust
15.Right hand drive vehicles - if steering wheel is to
right, drag link is too long. If steering wheel is to
left drag link is too short.
Left hand drive vehicles - if steering wheel is to
right, drag link is too short. If steering wheel is to
left drag link is too long.
16.Adjust drag link until steering wheel points
straight ahead when vehicle is travelling in a
straight line.
CENTRALISE STEERING BOX
1.To centralise the box, insert a suitable peg (hole
size 8.06 mm) into the rear of the drop arm and
into the steering box casing to enable rapid and
accurate setting on centre.

STEERING
3
ADJUSTMENT FRONT WHEEL ALIGNMENT
Service repair no - 57.65.01
Checking Toe-out dimensions
NOTE: No Adjustment is provided for
castor, camber or swivel pin inclinations.
1.Set vehicle on level ground with road wheels
positioned straight ahead.
2.Push vehicle back and forwards to settle linkage.
3.Measure toe-out at horizontal centre-line of
wheels.
4.Check tightness of clamp bolt fixings. Tighten to
14 Nm.
Adjust
5.Loosen adjuster sleeve clamp.
6.Rotate adjuster to lengthen or shorten track rod.
7.Check toe-out setting as instructions 1 to 4.
When toe-out is correct, tap steering linkage ball
joint, in directions of arrows shown, to maximum
of their travel. This ensures full unrestricted
working travel.
8.Tighten clamp bolts to
14 Nm.
POWER STEERING PUMP DRIVE BELT
Service repair no - 57.20.01
Adjust
NOTE: For details of drive belt adjust
procedure
See ENGINE, Repair, Drive
Belt

57STEERING
4
REPAIR
Refit
15.Position steering box to chassis side member,
ensuring locating peg is engaged. Tighten bolts
to
81 Nm.
16.Fit pinch bolt and nut securing universal joint to
power steering box. Tighten to
25 Nm.
17.Position tie bar, tighten bolts and nut to81 Nm,
starting with tie bar to mounting nut, then
loosen nut and bolts by one complete turn.
18.Check steering box, adjust if necessary.See
Adjustment, Power Steering Box
19.Refit drag link to drop arm tighten nut to40 Nm.
20.Fit undertray.
21.Lower vehicle to ground.
22.Remove plugs and refit pipes to steering box.
Tighten 16mm thread to
20 Nm.
14mm thread to15 Nm.
23.Remove filler cap. Fill reservoir to oil level mark
on dipstick. Use recommended fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids
and bleed power steering system.See
Power Steering System - Bleed
24.Recheck fluid level and replace cap.
25.With engine running, test steering system for
leaks by holding steering in both full lock
directions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute, to avoid oil overheating and
possible seal damage.
26.Test drive vehicle: using both full lock directions,
to settle steering components. If possible, drive
vehicle over speed bumps and include harsh
braking.
WARNING: Do not test drive vehicle on
public highway.
27.Drive vehicle in a straight line on level ground
and stop.
28.Tighten tie bar to mounting nut to
110 Nm.
29.Tighten bolts securing tie bar to81 Nm.
30.Ensure steering wheel is correctly aligned when
wheels are positioned straight ahead.
31.If necessary reposition steering wheel.
See
Steering Wheel
32.Road test vehicle.

STEERING
5
REPAIR POWER STEERING SYSTEM - BLEED
Service repair no - 57.15.02
1.Ensure fluid in reservoir reaches dipstick
maximum.
2.Run engine to normal operating temperature.
3.Recheck and correct reservoir fluid level.
NOTE: During instructions 4 to 6, maintain
maximum fluid level in reservoir. Do not
increase engine speed or move steering
wheel.
4.With engine at idle speed, loosen bleed screw.
When fluid seeps past bleed screw retighten
screw.
5.Check fluid level.
6.Clean away fluid around bleed screw.
7.Check hose connections, pump and steering box
for fluid leaks by holding steering on full lock in
both directions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute to avoid overheating fluid and
possibly damaging seals.
8.Carry out road test.POWER STEERING FLUID RESERVOIR
Service repair no - 57.15.08
Remove
1.Remove undertray.
2.Position drain tin beneath reservoir.
3.Loosen mounting bracket clamp bolt, raise
reservoir to gain access to pipe clamps.
4.Loosen clamps, disconnect feed and return
hoses from reservoir, allow fluid to drain.
CAUTION: Plug the connections.
5.Remove reservoir.
CAUTION: Discard fluid drained from
system. Do not allow fluid to contact
paintwork, if spilled, remove fluid and
clean area with warm water.

BRAKES
1
FAULT DIAGNOSIS ABS FAULT DIAGNOSIS
If a fault has occurred, or has been identified by ECU
self diagnostic function and ABS warning light is
illuminated. The system and components must be
checked to locate and rectify fault, using Testbook
diagnostics.
NOTE: If warning lamp has indicated a
fault in system, and no fault code has been
stored in memory, cause of fault is:
a) Failure in electrical supply
b) Bad ECU ground
c) Faulty warning light relay
d) ECU not connected
Before commencing fault diagnosis procedure
following items must be checked:
1.Inspect all exposed cables for damage or
abrasion.
2.Check ground on ABS system.
3.Battery - state of charge.
4.Check hub end-float.
5.All ABS fuses and electrical connections.
Fault rectification
1.Complete harness should be replaced if faults
are found in wiring harness.
2.DO NOT use unspecified cables or connectors,
as this could jeopardise safe function of ABS.
3.DO NOT attempt to open sealed 35 way
connector to ECU.FAULT DIAGNOSIS PROCEDURE
NOTE: If ABS warning light illuminates due
to large sensor air gap, fault will be
retained by the ECU memory. Where wheel
sensors have been pushed fully home prior to
test, The ECU will indicate a fault that has been
rectified.
NOTE: After any steering adjustment,
bearing replacement/adjustment, brake
disc replacement: Check hub end-float and
sensor clearance.
RELAYS AND FUSES ABS
The location and identification of ABS electrical relays
are given in the Electrical Troubleshooting Manual
For location and identification of ABS electrical fuses.
See ELECTRICAL, Repair, Fuse Box - Interioror.
See ELECTRICAL, Repair, Fuse Box - Engine
Compartment

BRAKES
1
REPAIR GENERAL BRAKE SERVICE PRACTICE
Brake fluid precautions
WARNING: Do not allow brake fluid to
come into contact with eyes or skin.
CAUTION: Brake fluid can damage
paintwork, if spilled wash off immediately
with plenty of clean water.
CAUTION: Use only correct grade of brake
fluid. If an assembly fluid is required use
ONLY brake fluid. Do NOT use mineral oil,
i.e. engine oil etc.
CAUTION: Thoroughly clean all brake
calipers, pipes and fittings before
commencing work on any part of the brake
system. Failure to do so could cause foreign
matter to enter the system and cause damage to
seals and pistons which will seriously impair the
efficiency of the brake system.
·To ensure the brake system efficiency is not
impaired the following warnings must be
adhered to :-
·DO NOT use any petroleum based cleaning
fluids or any proprietary fluids containing
petrol.
·DO NOT use brake fluid previously bled from
the system.
·DO NOT flush the brake system with any fluid
other than the recommended brake fluid.
The brake system should be drained and flushed
at the recommended service intervals.
Cover all electrical terminals carefully to make
absolutely certain that no fluid enters the
terminals and plugs.FLUID LEVEL CHECK / TOP UP
WARNING: Clean reservoir body and filler
cap before removing cap. Use only fluid
from a sealed container.
1.Park vehicle on level ground.
2.Check level is between 'MIN' and 'MAX' marks.
3.If level is below 'MIN' mark top up fluid level to
'MAX' mark on reservoir, using correct fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids
Do not fill reservoir above maximum line

HEATING AND VENTILATION
1
FAULT DIAGNOSIS HEATER OUTPUT
Symptom:-
Heater emits cold air.
1.Engine running: Check coolant valve opens as a
temperature control is moved from COLD.
2.Check for engine running cold.
See COOLING
SYSTEM, Fault diagnosis, Engine Runs Cold
3.Check heater pipes and hoses for blockage or
restriction.
4.Check heater matrix for blockage or restriction,
flush system.
Heater emits warm air.
5. Engine running:Check coolant valve closes
when both temperature controls are moved to
COLD.